Table of Contents
Advertisement
Messages
The following messages or service numbers appear on the television or unit's display when something unusual is detected during startup and use.
On the television
Authorisation Error.
This unit is not authorised to
play this title.
Cannot play.
Cannot play on this unit.
No disc is inserted.
Rental Expired.
$ This operation is not
available.
$ This operation is
prohibited by this disc.
Cannot connect.
Please check the connection
of the LAN cable.
IP address is not set.
Cannot obtain IP address.
Please check the connection
or setting of the router.
This IP address is already in
use.
Please check the setting.
Connection test could not be
conducted.
IP address is not set correctly.
Connection test was
unsuccessful. No reply from
Gateway. Please check the
connection or setting of the
router.
Network connection was
rejected.
Please confirm Setup
"BD-Live Internet Access".
Could not check for latest
firmware version.
Please try again later.
High Clarity Sound is effective.
Analog video output is turned off
when playback starts.
No Video
On the unit's display
F99
HDMI ONLY
NET
No PLAY
No READ
PLEASE WAIT
REMOVE
SET
("
" stands for a number.)
UNFORMAT
RQT9464
50
≥ [DivX] You are trying to play the DivX VOD content that was purchased with a different
registration code. You cannot play the content on this unit.
≥You inserted an incompatible disc.
≥You tried to play a non-compatible image.
≥The disc may be upside down.
≥ [DivX] The DivX VOD content has zero remaining plays. You cannot play it.
≥Some operations are unsupported by the unit. For example;
– [BD-V] : During play back, reverse slow-motion or reverse frame-by-frame is not possible.
≥Depending on the disc, you may not be able to perform search or skip when film
previews and warning screens are being played back.
≥When a hub is used but its Link lamp does not light up, check the cable connection,
LAN terminal connection, cable itself (a cross cable may be used by mistake), etc.
≥The "IP Address" in "IP Address / DNS Settings" is "---. ---. ---. ---". Set the "IP
Address", "Subnet Mask", and "Gateway Address". (Select the automatic address
acquisition if necessary.)
≥If you use a hub, then check the connection between the hub and the router.
– Use the UPLINK port of the hub to connect to a router.
– Check whether or not the hub's Link lamp lights up. If it does not light up, then check
the cable connection, LAN terminal connection, cable itself (a cross cable may be
used by mistake), etc.
≥If the above conditions are OK, then the router may not operate in DHCP mode. Check
the router settings and operation. You may reset the router to restore it to normal.
≥This unit's IP address is used by another device. Check the IP addresses of this unit,
personal computers, and routers, etc. If necessary, reconfigure them to avoid IP
addresses from being duplicated.
≥Turn the unit off. Remove the AC mains lead and reconnect it and try again. If the
same symptom persists, then consult your dealer.
≥If you use a hub, then check the connection between the hub and the router.
– Use the UPLINK port of the hub to connect to a router.
– If the hub's Link lamp does not light up, then check the cable connection, LAN
terminal connection, cable itself (a cross cable may be used by mistake), etc.
≥Check the "IP Address", "Subnet Mask", and "Gateway Address" in the "IP Address /
DNS Settings".
≥If the MAC address information is required, then press [SETUP] to display the
"Network Settings" menu.
≥When you set "BD-Live Internet Access" to "Limit" and play BD-Live contents which do
not have a content owner certificate, the Internet access of the content is not allowed.
If you allow the content to connect to Internet, set "BD-Live Internet Access" to
"Permit".
≥The firmware download server is currently unavailable. Please try again later.
≥"High Clarity Sound" in setup menu is set to "Enable", and "High Clarity Sound" in
on-screen menu is set to "On".
≥Depending on the connected iPod, video menu may not be available on the TV. Select
the iPod menu (iPod LCD) mode and operate video playback from your iPod menu.
≥The unit fails to operate properly. Press [Í/I] on the main unit to switch the unit to
standby for 3 seconds. Now press [Í/I] on the main unit again to turn the unit on.
≥Some BD-Video discs can only be output with HDMI.
≥Displays while VIERA CAST is starting up.
≥There is a viewing restriction on a BD-Video or DVD-Video.
≥The media is dirty or badly scratched. The unit cannot play.
≥The unit is carrying out internal process.This is not a malfunction. You cannot operate
the unit while "PLEASE WAIT" is displayed.
≥When connected to TV (VIERA) with HDAVI Control 4, and power supply is turned off
by the "Intelligent Auto Standby" function on the TV side.
≥The USB device is drawing too much power. Remove the USB device.
≥The remote control and main unit are using different codes. Change the code on the
remote control.
Press and hold [OK] and the indicated number button at the same
time for more than 5 seconds.
≥You inserted an unformatted DVD-RAM, DVD-RW, +RW, an unused +R, +R DL or
DVD-RW (DVD-Video format).
Page
20
42 – 45
42 – 45
—
20
—
—
11
31
11
11
—
—
11
31
31
35
—
34, 36
29
—
—
30
35
3
—
27
16
49
—
Advertisement
Table of Contents
