Page 1
DLP TV Chassis : L64C(N_ATSC)_Hurricane-2 Basic Model : HLR4266WX/XAA (HL-R4266W) Model : SP42L6HNX/XAX (SP-42L6HN) SERVICE Manual DLP TV FEATURES ■ ■ HD Built in TV ■ NTSC/ATSC Tuner Embedded ■ ■ AV network system (Anynet) ■ Digital Audio output (OPTICAL) jack ■...
Never change the part. space between the part and the printed circuit board. Check the AC power cord for possible damages. Keep the part or the lead away from any heat-emitting materials. Samsung Electronics...
Page 5
11. Pay additional attention to the current leakage as the voltage between the power board and the ballast is 220 to 440v, i.e. very high. And also beware of possible electric shock from the primary power source. Samsung Electronics...
5. Check for insulation between the blade of the AC plug 10. The sharp edges of the metal material may cause and that of any conductive materials (i.e. the metal physical damage, so ensure wearing protective gloves panel, input terminal, earphone jack, etc). during the repair. Samsung Electronics...
These servicing instructions are for use by qualified service personnel only. To reduce the risk of electric shock do not perform any servicing other than that contained in the operating instructions unless you are qualified to do so. Samsung Electronics...
4. Bend the external antenna cable when connecting it to the product. This is a measure to protect it from being exposed to moisture. Otherwise, it may cause a fire or electric shock. Samsung Electronics...
High definition. All RGB graphics signals are output as 30-bit 4:4:4 RGB or 20-bit 4:2:2 YCrCb. - MSP4440 : The MSP 44x0G family of single-chip Multistandard Sound Processors covers the sound processing of all analog TV-Standards worldwide, as well as the NICAM digital sound standards. Samsung Electronics...
- Side : 1 CVBS In, 1 S-VHS In - Rear : 2 RF In, 2 CVBS In, 2 S-VHS In, 2 Component In, 1 HDMI In(DVI Comportable With Adaptive Jack Only), 1 Anynet port, 1 Optical audio Samsung Electronics...
4. Actuator Gain adjustment : See page 3-15. 5. Vertical / Horizontal Position adjustment : See page 3-13. 6. CCA : See page 3-14. 7. Board LED check : Check all the LED are turned on. 8. Tilt/Focus adjustment : See page 3-17. Samsung Electronics...
Full Menu Display / Move to Parent Menu Item Selection by Moving the Cursor Direction keys ▲ / ▼ Data Increase/Decrease for the Selected Item Direction keys ◀ / ▶ Source Cycles through the active input source that are connected to the unit Samsung Electronics...
Lamp Boost 0~63 Lamp Boost value selection Lamp Sync Delay 0~4095 Lamp Sync delay value selection Engine Select SAMSUNG SAMSUNG and ZEISS Selection Lamp Watt 120W 120W/132W Selection Lamp Select Philips Philips/Osram/Ushio This displays the built-in pattern of the DDP1011 chip.
Page 19
Gain adjustment of the brightness for the Green signal BLU_B_COEFF Gain adjustment of the brightness for the Blue signal Sub Contrast 0~150 Brightness adjustment for the high-light parts of the screen Sub Brightness Brightness adjustment for the low-light parts of the screen ALPMAU/L 0~255 Samsung Electronics...
Page 20
Luma Automatic Gain Control LAGT Luma Automatic Gain Timing 1144 Luma Manual Gain CAGC Chroma Automatic Gain Control CAGT Chroma Automatic Gain Timing 2458 Chroma Manual Gain ON,OFF Chroma Transient Improvement Alpha Blend CTI_AB_EN Enable CTI_AB Chroma Transient Improvement Alpha Blend Samsung Electronics...
Page 24
0 ~ 3 C signal output delay YPFT YPFT adjustment YPFG YPFG adjustment 6. MSP4440 Item Range Default Remark MDB Effect 0~127 Micronas Dynamic Bass SRS Dialog 0~127 SRS Dialog clarity adjustment Pilot low adjustment Pilot high adjustment Samsung Electronics...
Page 25
Target Magenta X value for CCA DMagentaY Target Magenta Y value for CCA DYellowX Target Yellow X value for CCA DYellowY Target Yellow Y value for CCA D_White_X Target White X value for CCA D_White_Y Target White Y value for CCA ATV/AV/SV 3-10 Samsung Electronics...
Page 26
Dynamic Saturation On/Off Dynamic Sat Gain 0~255 Dynamic Saturation Gain Adjustment Sharp Picture Sharp Picture On/Off Sharp Filter HD Low HD High/HD Low/SD Image Sharp Picture Gain 0~255 Sharp Picture Gain Adjustment 11. CHECKSUM 0000 Excute Checksum calcuation Samsung Electronics 3-11...
Page 27
Auto Color function execution CCA menu Lamp Clear Initialize Lamp usage time User Reset All setting is back to the default Engine Select SAMSUNG SAMSUNG and ZEISS Selection Lamp Watt 120W 120W/132W Selection Lamp Select Philips Philips/Osram/Ushio 3-12 Samsung Electronics...
6. Press the ◀▶ (Left of Right) button to check the red color at the bottom of the screen at its minimum and maximum values of changing from red to magenta, then adjust to the mean value. Samsung Electronics 3-13...
Page 29
Measuring color coordinates data requires specific equipment not possessed by service per sonnel, that makes performing manual adjustment impossible. Adjusting CCA is applied to all the signal mode. Don't change Desired value because it will be hamful to the color of the SET. 3-14 Samsung Electronics...
Page 30
1) As shown in the picture above, change the actuator values to eliminate saw tooth shapes. - To fine tune, increase the data value ensuring that you get the center between the starting and ending points of the disappearing saw tooth shape. Samsung Electronics 3-15...
2) In order to enter the Service Mode, Press "Mute" → "1” → "8" → "2" → "POWER" buttons on the Remote Control. 3) In case entry into SERVICE MODE is unsuccessful, repeat steps 1 and 2 directly above. T_HUR3AUS0_XXXX 4) You can check the firmware version at the bottom of the Factory menu. 200X_XX_XX T-HURUCOM5-XXXX T-HUR3AUS1_XXXX 3-16 Samsung Electronics...
First, tighten the two screws on the left of the DMD board and then slowly tighten the one screw on the bottom right. Be careful not to touch the board while tightening the screws. (When using an electric-powered screwdriver, be careful that the torque is not too high.) Samsung Electronics 3-17...
Page 33
You put your hand in set below diagram. Move the focus alignment dial of Projection lens to the clockwise or counter clockwise until the picture is clear displayed. You are easy to work toghter another service man. 3-18 Samsung Electronics...
< Blinking Lamp and Temp LEDs > Is lamp cover installed? Install lamp cover CN101 Make sure lamp cover switch is activating Short CN101 on Check boss on Lamp Cover Sub-Detect Board Replace the Sub-Detect Board Replace the Digital Board Samsung Electronics...
Page 38
Replace Power Board Re-install lamp assy' Check pin 1 on CN503 Check 5Vpp at CN503 on DMD Board for 5V DC pin 3 on DMD Board Replace lamp assy' or ballast Replace DMD Board Replace ballast or lamp assy' Samsung Electronics...
Page 39
However, you can avoid outside light by changing the position of the TV or the installation angle. Decreasing the illumination or changing the indoor lighting may work. 9. Screen Flip-over: Enter Factory mode in DDP1011 and perform H-Flip (flip horizontally) and V-Flip (flip vertically). The screen will flip over horizontally or vertically. Samsung Electronics...
Page 40
Error in Rambus Dram(IC 403) or the soldering → Replace the DMD board ▶ Beehive mosaic patterns all over the screen: Error in the LVDS Receiver (IC 601) or the soldering The H sync signals are not transferred to DDP1011. → Replace the DMD board. Samsung Electronics...
Page 41
If "Pattern" does not appear, it may be from a DMD board or ATI error or there is an analog board malfunction. 4. Check if there is an error in the analog board. Check for a power signal from the analog to the digital boards. (See the circuit diagram below). CN105 Samsung Electronics...
Page 42
If necessary, Analog Board. 3) DMD Fan Check Cables connected to Check Cables connected to BALLAST. If necessary, Power Board. If necessary, replace BALLAST. replace Power Board. Check Cables connected to DMD Board. If necessary, replace DMD Board. Samsung Electronics...
◑ * It takes about 30 seconds for the TV to warm up, so normal brightness may not appear immediately. * The TV has a fan to keep the inside lamp from overheating. You'll occasionally hear it working. Samsung Electronics...
Page 44
The following is required: Factory Mode → Checksum → right button → checksum calculation → checksum output (ex: 0xab2b) ■ Examples T_ROBOAKR1_1010 : Checksum = 0xab2b T_ROBOAKR1_1014 : Checksum = 0x4faa Samsung Electronics...
Check to see if a blue flame starts igniting in the arc gap inside the ballast momentarily during start-up. There is no problem with the ballast if there is a flame. When the ballast has no error, replace the lamp. A blue flame occurs momentarily during start- Samsung Electronics...
Page 46
Check if the color wheel is running. + Check the DMD board and the ballast for the signals. Check the second CN503 pin for input signals. When 3.5V, 180Hz is output, the color wheel is operating normally. 3.5V, 180Hz From Color Wheel ※ DMD Board Check Diagram LAMP ENABLE 6-10 Samsung Electronics...
Page 47
2. Check if LAMPLITZ is Low Is the picture displayed? 3. Check if SYNCVALID is High 4. Check if DMD is properly connected 5. Check if VSYNCZ, HSYNCZ, ACTDATA and CLKIN are ready to be input Is a good image displayed? Samsung Electronics 6-11...
Page 48
1) OLCAT is flexible or always close to High 1) Check if DMD is properly connected 2) Check DMD Unclear or reverse image 3) Check DDP1011 4) Check the DMD drive voltage (VBIAS, VCC2, VRESET) Contact a DLP™ service person. 6-12 Samsung Electronics...
Block Diagram 7. Block Diagram 7-1 Overall Block Diagram Signal Power Light Signal c i t Anynet r r i USB Service Jack c i t a l l Samsung Electronics...
9-1-2 Names & Roles of Key Parts * CN801 : Supplies power (DC330V± 10%) to the ballast. * GT801 : Anti-lightning wire connected to the digital board. The anti-lightning wire should be installed for safety purposes. * PD801S : Connecting with power cable. Samsung Electronics...
Page 58
PCB Diagram 9-1-3 Power Board Connector Pin CN804 Connecting Power to Analog Board Pin Name PIN No. Pin Name STD 5V S-MUTE S14.5V S14.5V POWER-SW 5.5VB 5.5VB 12VB 12VB 12VB 12VB 80VB Samsung Electronics...
9-2 Digital Board 9-2-1 Assy Digital Board CN21 CN16 CN17 Reset Switch DVI to Board HDMI Anynet Digital ■ Microprocessor (Generates turn-on signal to power board) Optical ■ All Digital Video Processing Sound ■ OSD / Menu ■ Reset Switch Samsung Electronics...
* CN105 : Sends the power source from the analog to the digital board. * CN104 : This is a control signal terminal that connects between the analog and digital boards. * CN103 : This is an AV signal terminal that connects between the analog and digital boards. Samsung Electronics...
Page 63
Pin Name PIN No. Pin Name Connecting the IR signal 3.3V-ATI 3.3V-ATI Pin No. Pin Name 3.3VB-D 3.3V-ATI 3.3VB-D 6.5VA-D 5.7VB CN101 5.7VB Connecting front LED indicators 30VA Pin No. Pin Name 12VB KEY-PWR LED1 33VB LED2 LED3 Samsung Electronics...
* CN601 : The DVD cable terminal. This receives the image data from the digital board. * DMD PANEL : This is protected with a heat sink and fixtures. * DDP1011 : This processes the DMD drive and the signals. Samsung Electronics...
Schematic Diagram 10. Schematic Diagram 10-1 Analog Board 10-1-1 PowerSignal This Document can not be used without Samsung’s authorization. Samsung Electronics 10-1...
Page 68
Schematic Diagram 10-1-2 DCDC This Document can not be used without Samsung’s authorization. & 10-2 Samsung Electronics...
Page 69
Schematic Diagram 10-1-3 AV_Input This Document can not be used without Samsung’s authorization..P " " P " " Samsung Electronics 10-3...
Page 70
Schematic Diagram 10-1-4 A/V Switching This Document can not be used without Samsung’s authorization. c t i c t i c t i 10-4 Samsung Electronics...
Page 71
Schematic Diagram 10-1-5 AV_Comp_Buffer This Document can not be used without Samsung’s authorization. Samsung Electronics 10-5...
Page 72
Schematic Diagram 10-1-6 3D-Comb This Document can not be used without Samsung’s authorization. 10-6 Samsung Electronics...
Page 73
Schematic Diagram 10-1-7 Sound Processor/Amp This Document can not be used without Samsung’s authorization. s ’ Samsung Electronics 10-7...
Page 74
Schematic Diagram 10-1-8 S3F84BB_Micom This Document can not be used without Samsung’s authorization. 10-8 Samsung Electronics...
Page 75
Schematic Diagram 10-1-9 Signal Connection This Document can not be used without Samsung’s authorization. n i l > - o l l . . . Samsung Electronics 10-9...
Schematic Diagram 10-2 Digital Board 10-2-1 DTV Module-1 This Document can not be used without Samsung’s authorization. 10-10 Samsung Electronics...
Page 77
Schematic Diagram 10-2-2 DTV Module-2 This Document can not be used without Samsung’s authorization. o i t t e l c t i t i b c t i t i b Samsung Electronics 10-11...
Page 78
Schematic Diagram 10-2-3 DTV Module-3 This Document can not be used without Samsung’s authorization. Sound Video t e l c i t / 1 1 8 t e l / 1 9 7 t e l o i t t e l...
Page 79
Schematic Diagram 10-2-4 DTV Module-4 This Document can not be used without Samsung’s authorization. t l u Samsung Electronics 10-13...
Page 80
Schematic Diagram 10-2-5 DTV Module-5 This Document can not be used without Samsung’s authorization. Sound Video t l u 10-14 Samsung Electronics...
Page 81
Schematic Diagram 10-2-6 DTV Module-6 This Document can not be used without Samsung’s authorization. i t p i t p t l u Samsung Electronics 10-15...
Page 82
Schematic Diagram 10-2-7 DTV Module-7 This Document can not be used without Samsung’s authorization. Sound Video & 10-16 Samsung Electronics...
Page 83
Schematic Diagram 10-2-8 DTV Module-8 This Document can not be used without Samsung’s authorization. t l u t l u e r i i t c Samsung Electronics 10-17...
Page 84
Schematic Diagram 10-2-9 DTV Module-9 This Document can not be used without Samsung’s authorization. 10-18 Samsung Electronics...
Page 85
Schematic Diagram 10-2-10 DTV Module-10 This Document can not be used without Samsung’s authorization. Sound Video t i t t t i l Samsung Electronics 10-19...
Page 86
Schematic Diagram 10-2-11 DTV Module-11 This Document can not be used without Samsung’s authorization. t e l t e l 10-20 Samsung Electronics...
Page 87
Schematic Diagram 10-2-12 DTV Module-12 This Document can not be used without Samsung’s authorization. Sound Video n i t h t i Samsung Electronics 10-21...
Page 88
Schematic Diagram 10-2-13 DTV Module-13 This Document can not be used without Samsung’s authorization. Sound Video t e l i t p t e l 10-22 Samsung Electronics...
Page 89
Schematic Diagram 10-2-14 DTV Module-14 This Document can not be used without Samsung’s authorization. Sound Video : t l & : t l : t l Samsung Electronics 10-23...
Page 90
Schematic Diagram 10-2-15 DTV Module-15 This Document can not be used without Samsung’s authorization. Sound Video t e l 10-24 Samsung Electronics...
Page 91
Schematic Diagram 10-2-16 DTV Module-16 This Document can not be used without Samsung’s authorization. Samsung Electronics 10-25...
Page 92
Schematic Diagram 10-2-17 DTV Module-17 This Document can not be used without Samsung’s authorization. 10-26 Samsung Electronics...
Page 93
Schematic Diagram 10-2-18 DTV Module-18 This Document can not be used without Samsung’s authorization. Sound Video Samsung Electronics 10-27...
Schematic Diagram 10-9 Side-AV 10-11 RMC-LED This Document can not be used without Samsung’s authorization. This Document can not be used without Samsung’s authorization. 10-10 Key Control This Document can not be used without Samsung’s authorization. Sub-Front Circuit V0.4 : Connection Change Key-Control Schematic Diagram V0.4 : PCB Board Spec, Resister Value &...
Page 107
9-1-2 Names & Roles of Key Parts * CN801 : Supplies power (DC330V± 10%) to the ballast. * GT801 : Anti-lightning wire connected to the digital board. The anti-lightning wire should be installed for safety purposes. * PD801S : Connecting with power cable. Samsung Electronics...
Page 108
PCB Diagram 9-1-3 Power Board Connector Pin CN804 Connecting Power to Analog Board Pin Name PIN No. Pin Name STD 5V S-MUTE S14.5V S14.5V POWER-SW 5.5VB 5.5VB 12VB 12VB 12VB 12VB 80VB Samsung Electronics...
Page 109
9-2 Digital Board 9-2-1 Assy Digital Board CN21 CN16 CN17 Reset Switch DVI to Board HDMI Anynet Digital ■ Microprocessor (Generates turn-on signal to power board) Optical ■ All Digital Video Processing Sound ■ OSD / Menu ■ Reset Switch Samsung Electronics...
Page 111
PCB Diagram CN21 Connecting the Aduio/Video signal from the rear input terminal Pin Name PIN No. Pin Name MAIN_Y MAIN_C SUB_Y SUB_C DTV_CVBS COMP1_Y COMP1_Pb COMP1_Pr COMP2_Y COMP2_Pb COMP2_Pr M-CVBS M-SIF S-CVBS S-SIF Samsung Electronics...
Page 112
* CN105 : Sends the power source from the analog to the digital board. * CN104 : This is a control signal terminal that connects between the analog and digital boards. * CN103 : This is an AV signal terminal that connects between the analog and digital boards. Samsung Electronics...
Page 113
Pin Name PIN No. Pin Name Connecting the IR signal 3.3V-ATI 3.3V-ATI Pin No. Pin Name 3.3VB-D 3.3V-ATI 3.3VB-D 6.5VA-D 5.7VB CN101 5.7VB Connecting front LED indicators 30VA Pin No. Pin Name 12VB KEY-PWR LED1 33VB LED2 LED3 Samsung Electronics...
Page 115
* CN601 : The DVD cable terminal. This receives the image data from the digital board. * DMD PANEL : This is protected with a heat sink and fixtures. * DDP1011 : This processes the DMD drive and the signals. Samsung Electronics...
The mirror returns to a blank state so that no stains or after-images are left. The SAMSUNG SKY500N model has both an ANYNET port and a SERVICE jack port. Because the shape of the ANYNET port on the DLP TV is the same as that of the SERVICE jack port of the SKY500N, it fails to turn the TV off after a connection has been reported.
Page 118
Ex: For LCD 15:9 devices, "Wide" is displayed on the OSD instead of "16:9". 4. The picture size can be changed even in the blue screen. However, the picture size should be controlled by the product specifications if the change is impossible due to hardware restrictions. 14-2 Samsung Electronics...
Anynet An AV networking system of Samsung's various AV devices, English Captions (Subtitle) which enables the user to conveniently control AV devices A feature to provide English captions or character information using the TV.
Page 120
Reference Information S-video Terminal This is, called "Super-video", divided into video and color sig- nals for sharper image display. VHF/UHF VHF refers to the 2 - 13 channel system; UHF indicates the 14 - 69 channel system. 14-4 Samsung Electronics...
Page 123
① Separate the DVI cable. Chassis Notice: The DVI screw is made of soft plastic and may easily break when applying excessive force through a screw driver. Ensure that extreme caution is taken when loosening the screw. Samsung Electronics 12-1...
Page 124
Disassembly & Reassembly Part Name Description Description Photo Holder ① Seperate the Gt-wires. Chassis ② Seperate the cables. 12-2 Samsung Electronics...
Page 125
① Remove the 6 screws. : PWH,B,M3,L10,ZPC(YEL),SWRCH18A Analog ① Analog, Digital Board and Fan. Board/ Digital Board/ Digital ① Use the long-nosed pliers to remove the hex nuts. Board Nut-Hexagon : -,M3/8X32,ZPC(WHT),MBSBD Samsung Electronics 12-3...
Page 126
① After Removing the Top Shield Case. Notice: Use the two lock holes on either side of the shield case when removing it. ① Remove the 5 screws before removing the shield case at the bottom. : PWH,B,M3,L10,ZPC(YEL),SWRCH18A 12-4 Samsung Electronics...
Page 127
Disassembly & Reassembly Part Name Description Description Photo Digital ① Digital Board. Board Samsung Electronics 12-5...
Page 128
① Remove the screw and Remove the engine by pulling it out of the cabinet. : TH,B,M4.L15,BLK,SWRCH18A Notice: Be careful when removing the Light Engine as it may get caught up by the upper cable of the case. 12-6 Samsung Electronics...
Page 129
Notice: Wear gloves when handling the power board as there may be some remaining electrical charge in the capacitors. Specifically, avoid touching any part of the capacitors. ① After removing the 3 screws, separate the bottom power braket. : PWH,B,M3,L10,ZPC(YEL),SWRCH18A Samsung Electronics 12-7...
Description Description Photo Lamp ① Unplug the TV, then use a screwdriver to remove the 4 screws. : WSP,PH,+,M4,L12,ZPC(YEL),SM10C ① Remove the Lamp cover. ① Remove the screw securing the Lamp by using a screwdriver. : WSP,PH,+,M4,L12,ZPC(YEL),SM10C 12-8 Samsung Electronics...
Page 131
Disassembly & Reassembly Part Name Description Description Photo Lamp ① Separate the Lamp from the engine by holding the handle and pulling it out. ② To reinstall the Lamp, follow these steps in reverse order. Samsung Electronics 12-9...
Page 132
① Remove the Ballast SCI cable. ① Remove the two screws at the Holder Ballast. : PWH,+,B,M3,L10,ZPC(YEL),SWRCH18A,- ① Pull out the Ballast assembly. ② Replace it with a new one and re-assemble it in the reverse order. 12-10 Samsung Electronics...
Page 133
① Remove 2 screws to remove the color wheel cover. Wheel (L620 doesn't have the cover color wheel.) : WSP,PH,+,M3,L8,ZPC(YEL),SW ① Remove two cables at the DMD Board. ① Remove 2 screws. : PWH,+,B,M3,L10,ZPC(YEL),SWRCH18A,- ① Disassemble the color wheel assembly. Samsung Electronics 12-11...
Page 134
Disassembly & Reassembly Part Name Description Description Photo Color ① Replace it with a new color wheel and rubber assembly. Wheel Notice : Never touch the color wheel. Touch only the cover assembly. 12-12 Samsung Electronics...
Page 135
Disassembly & Reassembly 12-1-8 Actuator(Smooth Picture) Replacement Part Name Description Description Photo Actuator ① Remove the cable at the Actuator. ① Push the steel spring wire to bottom of the Actuator Assy. ① Replace it with a new actuator. Samsung Electronics 12-13...