Page 1
CDP-XE800 SERVICE MANUAL AEP Model Model Name Using Similar Mechanism CD Mechanism Type CDM36-14 Base Unit Type BU-14 Optical Pick-up Type KSS-213B/S-N SPECIFICATIONS COMPACT DISC PLAYER MICROFILM — 1 —...
COMPONENTS IDENTIFIED BY MARK ! OR DOTTED LINE WITH MARK ! ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS LIST ARE CRITICAL TO SAFE OPERA- TION. REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY.
SECTION 1 SERVICING NOTE HOW TO OPEN THE DISC TRAY WHEN POWER SWITCH NOTES ON HANDLING THE OPTICAL PICK-UP BLOCK TURNS OFF OR BASE UNIT The laser diode in the optical pick-up block may suffer Insert a screwdriver into the aperture of the unit bottom, and electrostatic breakdown because of the potential difference move it in the direction of arrow.
SECTION 3 DISASSEMBLY Note : Follow the disassembly procedure in the numerical order given. 3-1. FRONT PANEL ASSEMBLY 1 Push the part A in the direction of arrow to remove the loading panel upward. A part 5 Two screws (BVTP2.6x8) 7 Panel bracket 3 Connector Claw...
SECTION 4 TEST MODE 4-1. AF MODE Button No. Button No. Button Button The following checks can be performed in the AF mode, which is Displayed Displayed set by connecting the TP2 (AFADJ : JW76) terminal on MAIN TIME ENTER board to the Ground and turning on the power.
Page 7
4-2. ADJ MODE [ MAIN BOARD ] — Component Side — The following operations are performed in the ADJ mode, which is set by connecting the TP1 (ADJ : JW75) terminal to the Ground and turning on the power. • During playback, there is no problem even if the GFS is continu- CN302 ously LOW.
SECTION 5 ELECTRICAL BLOCK CHECKING Note: A clear RF signal waveform means that the shape “◊” can be Note: clearly distinguished at the center of the waveform. 1. CD Block is basically designed to operate without adjustment. Therefore, check each item in order given. RF signal waveform 2.
Page 9
6. Check the level B of the oscilliscope's waveform and the A (DC RF PLL Free-run Frequency Check voltage) of the center of the Traverse waveform. Procedure : Confirm the following : 1. Connect frequency counter to test point (XPLCK) with lead wire. A/B x 100 = less than ±...
6-2. IC PIN FUNCTION • IC801 SYSTEM CONTROL, FLUORESCENT INDICATOR TUBE DRIVE (CXP82316-060Q) Pin No. Pin Name Function TIMER – Connected to +5V. RM (BUSIN) Audio bus input. – Connected to +5V. OPEN – OPEN – Not used. (open) (BUS-OUT) –...
7-2. CHASSIS SECTION CD MECHANISM (CDM36-14) CNP901 T901 not supplied The components identified by mark ! or dotted line with mark not supplied ! are critical for safety. Replace only with part number specified. Ref. No. Part No. Description Remark Ref.
7-3. CD MECHANISM SECTION (CDM36-14) BASE UNIT (BU-14) not supplied not supplied not supplied not supplied M151 not supplied not supplied not supplied not supplied Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 1-452-820-11 MAGNET (ASSY) 4-968-905-01 BELT (CDM) * 102 4-977-902-01 PANEL (DRAWER)
7-4. BASE UNIT SECTION (BU-14) M101 not supplied M102 The components identified by mark ! or dotted line with mark ! are critical for safety. Replace only with part number specified. Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 4-977-925-01 SPRING(SLIDE BASE),COMPRESSION...
http://getMANUAL.com SECTION 8 ELECTRICAL PARTS LIST Note: • Due to standardization, replacements in the parts list • SEMICONDUCTORS The components identified by may be different from the parts specified in the dia- In each case, u: µ , for example: mark ! or dotted line with mark grams or the components used on the set.
Page 21
DISPLAY Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R114 1-216-073-00 METAL CHIP 1/10W < SWITCH > R117 1-216-073-00 METAL CHIP 1/10W R118 1-216-073-00 METAL CHIP 1/10W S152 1-762-010-11 SWITCH, LEVER (LOAD IN SW) S153 1-762-010-11 SWITCH, LEVER (LOAD OUT SW) R121 1-216-073-00 METAL CHIP 1/10W...