Panasonic WV-CW244F Operating Instructions page 2

● Heater unit installation
See OPTIONAL HEATER UNIT for details.
Supplied screw Supplied screw
Adhesive tape Adhesive tape
Fold Fold
Point "A" Point "A"
(inside the wall) (inside the wall)
● Mounting the camera
1. Fix the camera to the installation surface.
WV-CW244F
• Fix the camera on the junction box using four screws (locally procured).
WV-CW244S
• Fix the supplied bracket on the wall/ceiling using four screws (locally procured).
• Fix the camera on the bracket using four screws (supplied).
2. Perform connections referring to ■ Connections.
3. Reinstall the camera to the bracket or junction box referring to step 1 above.
4. Adjust the image referring to ■ Image Adjustment.
5. Apply waterproof means referring to ● Waterproof Process.
■ Connections
● Video Output Connection
● Cable Length and Wire Gauge
Connect the video output connector to the mon- 24 V AC
The recommended cable length and thick-
itor or other system device with the procured
ness are shown in the table for reference.
coaxial cable. The maximum extensible length
is shown in the table. The voltage supplied to the power terminals
of the camera should be within 19.5 V AC
and 28 V AC.
Type of RG-59/U RG-6/U RG-11/U RG-15/U
coaxial cable (3C-2V) (5C-2V) (7C-2V) (10C-2V)
Recommended (m) 250 500 600 800 Recommended wire gauge for 24 V AC line.
maximum
Copper wire #24 #22
cable length (ft) 825 1 650 1 980 2 640
size (AWG) (0.22 mm 2 ) (0.33 mm 2 ) (0.52 mm
Length of (m) 95 150
Cable
(Approx.) (ft)
314 495
● Power Connection
12 V DC
● Wire Colors & Functions
Use the formula below to calculate the
Camera power cable
power cable and power supply. The voltage
supplied to the power terminals of the cam-
era should be within 10.5 V DC and 16 V
DC.
Resistance of copper wire [at 20 °C (68 °F)]
Copper wire #24 #22
size (AWG) (0.22 mm 2 ) (0.33 mm 2 ) (0.52 mm
Resistance
0.078 0.050
Ω/m
Resistance
Wire Color 24 V AC 12 V DC 0.026 0.017
Ω/ft
Black 24 V AC (L) Positive
White 24 V AC (N) Negative
10.5 V DC ≤ V − 2(R x I x L) ≤ 16 V DC
A
Green/Yellow Ground Not Used
L : Cable length (m) (ft)
R : Resistance of copper wire (Ω/m) (Ω/ft)
Heater power cable
V : DC output voltage of power supply unit
A
I : DC current consumption (A). See spec-
ifications.
Wire Color 24 V AC
Red 24 V AC (L)
White 24 V AC (N)
Caution:
• Be sure to connect the GND (grounding)
lead of the camera and grounding terminal
of the power supply when using a 24 V AC
power source.
■ Image Adjustment
You can manually adjust the pan/tilt/azimuth
angles, focus, and zoom while observing the
Harness Harness
connected monitor.
Pan lock screw (stainless)
Notes:
• Do not hold the camera by lens unit to
adjust panning, tilting, or azimuth.
• The video output to the BNC will be inter-
rupted while an LCD monitor is connected
to the video jack.
1. Connect an LCD monitor to the video jack.
2. Pan/tilt/azimuth adjustment
• Loosen the two screws locking the pan and
tilt tables.
• Pan and tilt the table to aim the camera at
what you need to watch.
• Turn the azimuth adjuster to obtain a level
image.
• Tighten the two screws after adjusting.
3. Zoom
• Unlock the zoom lever.
• Move the lever to adjust the zoom.
• Lock the lever.
FAR
TELE
WIDE
4. Focus
• Unlock the focus lever.
• Move the lever to adjust the focus.
• Lock the lever.
#20 #18
5. Reinstalling the dome cover
2 ) (0.83 mm 2 )
• Attach the dome cover to the camera.
255 425
• Tighten the three tamper-proof screws.
842 1 403
● Waterproof Process
When necessary, apply waterproof process to protect the camera from water soak.
1. Power cord
First, tape the individual wires, finally all of them as a whole.
#20 #18
2 ) (0.83 mm 2 )
Power cord
0.03 0.018
0.010 0.006
2. Connector junctions
Tape the BNC-BNC junction point.
Video output cable
3. Gaps and holes
Apply such a waterproof material as silicone clay (rubber) to the gaps, screws, holes, and other
relevant portions.
4. Camera Fixing Screws
WV-CW244F
Be sure to apply silicone rubber to the camera fixing screws in case of outdoor installation.
WV-CW244S
If you use camera fixing screws that are locally procured, be sure to apply silicone rubber to
the screws.
SPECIFICATIONS
Variable angles
plus or minus 75 °
Pick-up device:
(max.)
Scanning area:
Scanning:
Horizontal:
Vertical:
Synchronization:
Video output:
Horizontal resolution:
Signal-to-noise ratio:
Minimum illumination:
Detail:
Tilting lock screw
White balance:
(stainless)
Panning table
Lens Mount:
Lens
Focal length:
Maximum aperture ratio:
Angular field of view:
Focusing range:
Ambient operating temperature:
Ambient operating humidity:
Power source and
Power consumption:
Dimensions:
Azimuth adjuster
Weights:
Weights and dimensions indicated are approximate.
Specifications are subject to change without notice.
STANDARD ACCESSORIES
Operating Instructions (this document) ............................................. 1 pc.
NEAR The following are for installation.
Tamperproof screw bit ...................................................................... 1 pc.
Camera mounting bracket (supplied only to WV-CW244S) ............... 1 pc.
Camera fixing screw (with a plastic washer) ..................................... 4 pcs.
(supplied only to WV-CW244S)
Zoom lock lever
Focus lock lever
OPTIONAL ACCESSORIES
Heater unit ......................................................................................... WV-CW3H
Clear dome cover .............................................................................. WV-CW2C
Camera mounting bracket (for WV-CW244F) .................................... WV-Q112
OPTIONAL HEATER UNIT
■ Optional Heater Unit WV-CW3H
768 (H) x 494 (V) pixels, Interline transfer CCD
4.8 (H) x 3.6 (V) mm (Equivalent to 1/3" pick-up tube)
● Introduction
525 lines/60 fields/30 frames
15.734 kHz
Installing this heater unit enables the camera to operate under in a low-temperature environment of
59.94 Hz –30°C (–22°F). The heater turns on automatically when the temperature inside the camera drops
Internal, Line-lock (only 24 V AC), or Multiplexed vertical drive
below +10°C (50°F) and turns off when it rises.
(VD2)
A small fan inside the unit will minimize condensation on the surface of the dome cover caused by
1.0 V [P-P] NTSC composite 75 Ω/BNC connector
changes in ambient temperature unless temperatures change too rapidly. The fan will stop when
480 lines
there is no possibility of condensation.
50 dB (Equivalent to AGC Off, weight On)
2.4 lx (0.24 footcandle) (WIDE),
When the optional WV-CW2C dome cover is installed. ● Precautions
1.0 lx (0.1 footcandle) (WIDE),
• This product should be installed and connected by qualified service personnel or system
SHARP or SOFT, selectable
installers.
ATW
• Do not use the same 24 V AC power source supplying the power to the camera for the heater
CS-mount
unit. Connect another 24 V AC power source to the heater unit. If the same power source is
used, turning the heater on and off may disturb the camera images.
3.8 mm - 8 mm
• When servicing, pay attention to high temperature on the surface of the unit. Disconnect the har-
1:1.4 (Wide), 1:1.8 (Tele)
ness and wait until it cools.
Horizontal: 35.6 ˚ - 73.6 ˚
• When you install the camera in a low-temperature location and start operating it, it may take time
Vertical: 26.6 ˚ - 53.4 ˚
(around 30 minutes) for the inside of the
1.2 m - ∞ (3.9 ft - ∞)
camera to warm up. Cut power once then
–10 °C - +50 °C (14 °F - 122 °F)
supply power again.
–30 °C - +50 °C (–22 °F - 122 °F)
(When the optional heater unit built in)
Less than 90 %
● Installation
1. Open the dome cover. (See Disassembling
12 V DC, 265 mA (Camera)
24 V AC 60 Hz, 3.0 W (Camera) the camera.)
2. Place the heater unit in the camera and fix
24 V AC 60 Hz, 12.1 W (Heater unit)
WV-CW244F: 133 mm (H) x 152.5 mm (D) it with the supplied screw.
5-1/4" (H) x 6" (D) 3. Insert the harness into the heater unit con-
nector of the camera.
WV-CW244S: 136.5 mm (H) x 160 mm (D)
5-3/8" (H) x 6-5/16" (D) 4. Fold the desiccant pack in half, and attach
it with adhesive tape to point "A" shown in
WV-CW244F: 1.2 kg (2.7 lbs.)
the figure.
WV-CW244S: 1.7 kg (3.8 lbs.)
Note: Attach the desiccant pack so that it
does not block ventilation holes or
hang over the top of the wall.
5. Attach the dome cover while paying atten-
tion not to pinch the harness cable.
6. Connect the heater power cable of the camera. (See Connection.)
● Specifications
Required power:
Power consumption:
Dimensions:
Weights:
● Accessories
Fixing screw (M3 x 12) ...................................1 pc.
Desiccant pack .............................................1.pc.
Panasonic Digital Communications & Security Company
Unit of Matsushita Electric Corporation of America
Security Systems Group
www.panasonic.com/cctv
Executive Office: One Panasonic Way 3E-7, Secaucus, New Jersey 07094
Zone Office
Eastern: One Panasonic Way, Secaucus, NJ 07094 (201) 348-7303
Central: 1707 N.Randal Road, Elgin, IL 60123 (847) 468-5205
Western: 6550 Katella Ave., Cypress, CA 90630 (714) 373-7840
2003 © Matsushita Electric Industrial Co., Ltd. All rights reserved.
Supplied screw
Supplied screw
Adhesive tape Adhesive tape
Harness
Harness
Fold
Fold
Point "A"
Point "A"
(inside the wall)
(inside the wall)
24 V AC, 60 Hz
12.1 W maximum
29 mm (H) x 83 mm (W) x 89.5 mm (D)
[1-1/8" (H) x 3-1/4"(W) x 3-1/2"(D)]
45 g (0.1 lbs)
PANASONIC CANADA INC.
5770 Ambler Drive, Mississauga,
Ontario, L4W 2T3 Canada (905)624-5010
PANASONIC SALES COMPANY
DIVISION OF MATSUSHITA ELECTRIC OF PUERTO RICO INC.
San Gabriel Industrial Park 65th Infantry Ave. KM. 9.5 Carolina,
P.R. 00985 (809)750-4300