Panasonic WV-CW244F Operating Instructions

Color CCTV Camera
Operating Instructions
WV-CW244F
Model No.
WV-CW244S
Before attempting to connect or operate this product,
please read these instructions carefully and save this manual for future use.
N0803-1093 3TR001693BAA
NOTE: This equipment has been tested and found
to comply with the limits for a Class A digital
device, pursuant to Part 15 of the FCC Rules.
CAUTION
These limits are designed to provide reasonable
protection against harmful interference when the
RISK OF ELECTRIC
equipment is operated in a commercial environ-
SHOCK DO NOT OPEN
ment. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed
and used in accordance with the instruction manu-
al, may cause harmful interference to radio com-
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
munications.
DO NOT REMOVE COVER (OR BACK).
Operation of this equipment in a residential area is
NO USER-SERVICEABLE PARTS INSIDE. REFER SER-
likely to cause harmful interference in which case
VICING TO QUALIFIED SERVICE PERSONNEL. the user will be required to correct the interference
at his own expense.
FCC Caution: To assure continued compliance,
The lightning flash with arrowhead
(example - use only shielded interface cables when
symbol, within an equilateral trian-
connecting to computer or peripheral devices). Any
gle, is interned to alert the user to changes or modifications not expressly approved
the presence of uninsulated "dan- by the party responsible for compliance could void
the user's authority to operate this equipment.
gerous voltage" within the product's
enclosure that may be of sufficient
SA 1965 magnitude to constitute a risk of
electric shock to persons.
This Class A digital apparatus complies with cana-
dian ICES-003.
The exclamation point within an Cet appareil numérique de la classe A est
conforme à la norme NMB-003 du Canada.
equilateral triangle is intended to
alert the user to the presence of
important operating and mainte-
nance (servicing) instructions in the
literature accompanying the appli- The serial number of this product may be found on
ance. the top of the unit.
SA 1966
You should note the serial number of this unit in the
space provided and retain this instruction as a per-
manent record of your purchase to aid identification
in the event of theft.
Model No.
Serial No.
WARNING: To prevent fire or electric shock hazard, do not expose this appliance to rain or moisture.
The apparatus shall not be exposed to dripping or splashing and that no objects filled with liquids, such
as vases, shall be placed on the apparatus.
PREFACE
The WV-CW244 series is a 1/3" CCD color cam- quality thanks to the use of digital signal pro-
era designed for use in a video surveillance cessing LSIs, and easy installation.
system. The camera features a high picture
FEATURES
• Mounting method: Flash mounting/WV- • Minimum illumination: 2.4 lx (0.24 foot-can-
CW244F, Surface mounting/WV-CW244S dle) at WIDE
• Signal processing: Automatic Light Control • Signal-to-noise ratio: 50 dB (Equivalent to
(ALC), Automatic Gain Control (AGC), AGC OFF)
Automatic Tracing White Balance (ATW), • Horizontal resolution: 480 TV lines
etc. • Optional heater unit available for the cam-
• Synchronization: Internal, Line-Lock (only era used at temperatures between –10 ˚C
24 V AC), and Multiplexed Vertical Drive and –30 ˚C (14˚F and –22˚F).
(VD2)
PRECAUTIONS
1. This product should be installed and con- 7. Clean the lens faceplate with care.
nected by qualified service personnel or Do not clean the lens with strong or abra-
system installers in conformity with NEC. sive detergents. Use lens tissue or a cotton
tipped applicator and ethanol.
2. Use a class 2 power source supplying 12 V
DC or 24 V AC. 8. Never face the camera towards the sun.
Do not aim the camera at bright objects.
3. To prevent fire or electric shock hazard, use Whether the camera is in use or not, never
a UL listed cable (VW-1, style 1007) to con- aim it at the sun or other extremely bright
nect the power supply to the camera. objects. Otherwise, blooming or smear may
be caused.
4. Be sure to use a ceiling board/wall having
enough strength to support this camera. 9. Do not operate the camera beyond its
specifications.
5. Handle the camera with care. Use the camera under conditions where
Do not abuse the camera. Avoid striking, temperature is between –10 °C to +50 °C
shaking, etc. The camera could be dam- (14 °F to 122 °F), and humidity is below
aged by improper handling or storage. 90 %. The input power source is 24 V AC or
12 V DC.
6. Do not use strong or abrasive
detergents. 10. Use a monitor whose resolution is at least
Use a dry cloth to clean the camera body equal to that of the camera.
when dirty.
Printed in Japan
In case the dirt is hard to remove, use a
mild detergent and wipe gently. Afterwards,
wipe off the remaining detergent with a dry
For U.S.A
cloth.
MAJOR OPERATING CONTROLS AND THEIR FUNCTIONS
For Canada
q w
2nd transport protection screw (Red)
u
i
o
!0
OFF ON
SYNC LL INT*
!1
BLC OFF* ON
AP SOFT SHARP*
* Default setting
q Focus lock lever i Synchronization Mode Selector
Fixes the focus position after adjusting. Specifies a source for synchronization.
INT: Internal 2:1 interlace.
w Tilting lock screw LL: Line-lock mode driven by 24 V AC.
Fixes the tilting position after adjusting. The default setting is INT.
Note: Do not set the switch to LL (Line-
e Zoom lock lever
Fixes the zoom position after adjusting.
r Panning table o Back Light Compensation Selector
Adjusts the panning angle of the camera. ON: Compensates the background if it is
t Azimuth adjuster OFF: Does not compensate.
Adjusts the azimuth angle to obtain a level The default setting is OFF.
image.
!0 Aperture Level Selector
y Pan lock screw
SHARP: Sharpens the image outline.
Fixes the panning position after adjusting. SOFT: Softens the image outline.
The default setting is SHARP.
u Heater power connector
Supplies power to the optional heater unit !1 Video jack (3.5-diam. mini jack)
when it is built in the camera. Connect here For connecting an LCD monitor to adjust
a harness sticking out from the heater unit. the camera images. Use an L-type plug to
save space.
!2 Dome cover
!3 Video output cable with BNC connector
Connects with the video connector of the
monitor.
!4 Camera power cable
Supplies 24 V AC or 12 V DC from an exter-
nal power source.
INSTALLATION
■ Installation Plans & Preparations
● WV-CW244F
"F" stands for flash mounting. This model can be mounted on a two-gang junction box (4" x 4") pre-
installed in the wall or ceiling.
Space for heater unit
e
r
t
y
Camera fixing screw x 4 (procured locally)
1. Space
Prepare a space larger than ø160 mm.
2. Junction box
Procure and install a junction box that meets the dimensions in the figure.
3. Camera Fixing Screws
Procure four screws (M4) suitable for the junction box.
4. Cable route
Cables will go behind the junction box.
5. Waterproof Process
When necessary, apply waterproof process to the camera and relevant portions.
Be sure to apply silicone rubber to the camera fixing screws in case of outdoor installation.
Lock) position when supplying 12 V DC
to avoid synchronization error.
brighter than the object.
● WV-CW244S
!2
"S" stands for surface mounting. This model can be installed on the surface of the wall or ceiling
using the supplied bracket.
!3
!4
!5
!6
Bracket fixing screw x 4
(procured locally)
!5 Heater power cable
Supplies 24 V AC from an external power
source to an optional heater.
!6 Camera mounting bracket
Only WV-CW244S (surface mount type) is
supplied with a mounting bracket for ceiling
installation.
Camera fixing screw x 4 (supplied)
1. Space
Prepare a space larger than ø160 mm.
2. Bracket Fixing Screws
To fix the bracket, procure four M4 screws suitable for the surface and structure of the wall/ceil-
ing.
3. Camera Fixing Screws
Four screws are supplied as standard accessories.
4. Cable route
• When routing cables through the wall/ceiling, drill a hole as shown in the figure.
• When routing cables sideway, open the sideway cable exit unscrewing the lid by use of a hexa-
gon wrench. Screw the detached lid to the cable access hole on the bottom of the bracket.
46mm
(1-13/16")
5. Waterproof Process
When necessary, apply waterproof process to the camera and relevant portions.
If you use camera fixing screws that are locally procured, be sure to apply silicone rubber to the
screws.
■ Mounting the Camera
● Disassembly of the camera
1. Remove the dome cover by loosening three
tamper-proof screws using the supplied bit.
2. Remove the two red-colored screws provid-
ed for transport protection using a Philips
screwdriver.
85 mm
(3-3/8")
Cable access hole
for 3/4" pipe
Bracket center
2nd transport
protection screw