Yamaha DTX920K Assembly Manual

ELECTRONIC DRUM KIT
DTX760K/DTX920K
This manual describes the standard assembly procedure for the DTX760K/DTX920K electronic drum kits. It covers assembly and wiring of the kit as shown below.
When you have completed all of the steps described, you will be ready to turn on the drum trigger module and start playing.
Illustrations show the DTX700 drum trigger module.
Example of standard assembly
PCY135 PCY155
(Cymbal Pad) (Cymbal Pad)
CH750
(Cymbal Holder)
XP100T
RHH135
(Tom Pad)
(Real Hi-hat Pad)
DTX700/DTX900M
Drum Trigger Module
HS740A
(Hi-hat Stand)
XP120SD
(Snare Pad)
SS662
(Snare Stand)
Safety Precautions
The purpose of the precautions detailed below is to ensure that this electronic drum kit can be used safely without fear of injury or property damage. As a means of indicating the severity and immediacy
of any risk of injury or property damage resulting from incorrect operation, these precautions are classified as either WARNING or CAUTION. The instructions displayed together with these precautions
are extremely important in terms of ensuring safety, and therefore, they should be fully observed.
* After reading this Assembly Manual, ensure that it is kept in a safe, convenient location for future reference.
* Be sure to also read the Assembly Manuals and/or Owner's Manuals that came with your pads and rack.
Failure to observe the precautions described below can result in se-
WARNING
rious injury or even death.
• Young children using this electronic drum kit should be supervised by a guardian to eliminate any
possibility of injury.
• Holders for cymbal and tom pads have sharp tips. In order to avoid injury, therefore, you should
take special care whenever handling these components.
• The anti-slip stoppers on kick pads and foot pedals have sharp tips. In order to avoid injury, there-
fore, you should take special care whenever handling these components.
• Be sure to securely tighten nuts and other fasteners when setting up this electronic drum kit. In
addition, be sure to proceed slowly when loosening nuts. If this precaution is not observed, pads
may fall off or the rack may collapse or fall over, possibly causing injury.
• Do not setup this electronic drum kit on a slope, on an unstable platform, or on any other unsafe
surface. If this precaution is not observed, it may topple over or fall, possibly causing injury.
• Whenever setting up this electronic drum kit, ensure that cables and the like are arranged safely. If
someone were to trip on a cable, the kit could topple over and cause injury.
• Under no circumstances should this electronic drum kit be disassembled or customized. Failure to
observe this precaution can result in injury or malfunction.
• Do not sit or stand on the rack. Doing so could cause it to fall over or break, possibly causing injury.
* Specifications and descriptions in this owner's manual are for information purposes only. Yamaha Corp. reserves the right to change or modify products or specifications at any time
without prior notice. Since specifications, equipment or options may not be the same in every locale, please check with your Yamaha dealer.
Manual Development Department
©2015 Yamaha Corporation
Published 10/2015 POTO*.*-**A0
Printed in Japan
EN
Assembly Manual
ZT57980
IMPORTANT
• For assembly, you will require four individual packages – an RS700
Rack System, a DTP903 Pad Set, a DTP904 Pad Set, and a DTX700/
DTX900M Drum Trigger Module.
• This manual describes the process of assembling a drum-pad set and
drum trigger module to an already assembled RS700 Electronic Drum
Rack. Before starting the steps below, therefore, be sure to assemble
CH750
your RS700 as described in the Owner's Manual that came with it.
(Cymbal Holder)
NOTICE
Before starting assembly, lay a drum mat (sold separately) on the floor.
Alternatively, you can place cardboard from the drum kit packaging or the
PCY135
like on the floor to prevent it from being scratched. This is particularly
(Cymbal Pad)
important when using the HS740A Hi-hat Stand and KP100 Kick Pad.
CH755
(Cymbal Holder)
XP120T
(Tom Pad)
RS700
KP100 (Rack System)
(Kick Pad)
Please read carefully before proceeding.
Failure to observe the precautions described below can result in in-
CAUTION
jury and/or property damage.
• Mind your fingers when adjusting clamps. They can easily be crushed if care is not taken during
this operation.
• Be careful with the tips of supports, arms, screws, and the like. Fingers can easily be injured by
sharp tips if these components are not handled carefully.
• Do not place hands or feet under a kick pad or foot pedal. Doing so could result in injury.
• Do not use the electronic drum kit's rack to hold acoustic drums. Doing so could cause clamps to
break and the drums to fall off, which in turn could lead to injury.
NOTICE: Usage Precautions
• When connecting and disconnecting cables, be sure to hold the plug and not the cable itself. In addition,
avoid placing heavy items on top of cables and do not allow them to touch sharp edges. Failure to avoid
these precautions can lead to cable breakage and disconnection.
• Do not climb onto the electronic drum kit and avoid placing heavy objects on it. Failure to observe this pre-
caution can result in malfunction.
• Avoid using or storing the electronic drum kit in very hot locations (i.e., in direct sunlight, in close proximity to
a heater, or in a closed vehicle) or in highly humid locations (i.e., in a bathroom or outdoors in wet weather).
Failure to observe this precaution can lead to warping, discoloration, malfunction, or breakdown.
• Avoid cleaning the electronic drum kit with organic solvents, paint thinner, or alcohol as these substances
can cause warping and discoloration. Instead, we recommend you remove dust using a soft dry cloth or
wipe clean using a moist, tightly-wrung cloth. If the electronic drum kit is very dirty, first wipe the dirt away
using a cloth moistened with a neutral detergent solution and tightly wrung. Following this, wipe away the
detergent solution using a cloth soaked in water and tightly wrung.
1 Assemble the RS700 Electronic Drum Rack.
For instructions on how to assemble the RS700 Electronic Drum Rack, refer to the Owner's Manual that came with it.
Open the boxes to reveal their contents.
2
Package 1: DTP903
 PCY135  PCY155  RHH135
Cymbal Pad (x2) Cymbal Pad (x1) Real Hi-hat Pad (x1)
 CH750  KP100  SS662
Cymbal Holder (x2) Kick Pad (x1) Snare Stand (x1)
 2.5m stereo phone cables (x4)  4m stereo phone cables (x6)
 KP100 Owner's Manual (x1)  Tuning key (x1)
 PCY100/PCY135/PCY155 Owner's Manual (x1)
 RHH135 Owner's Manual (x1)
3 Assemble the pads and the drum trigger module to the electronic drum rack.
Assembling the cymbal holders
1.
Assemble the cymbal holders (CH750 x 2, CH755 x 1) on the electronic
drum rack as shown below.
CH750
CH750
CH755
Package 2: DTP904
 Stand base for the  XP120SD  XP100T
RHH135 (x1) Snare Pad (x1) Tom Pad (x2)
 Hi-hat clutch for the
RHH135 (x1)
 Clamp bolts (x3)  CH755
Cymbal Holder (x1)
 Cable band for the
RHH135 (x1)
 Stoppers for the
PCY135 and
PCY155 (x3)
 XP100T/100SD/120T/120SD Owner's Manual (x1)
 Assembly Manual (this pamphlet)
Package 3: DTX700/DTX900M
 Felts for the
PCY135 and
 DTX700/DTX900M  Module holder (x1)
PCY155 (x3)
Drum Trigger Module (x1)
 Cable bands (x10)
 AC power adaptor* (x1)
* May not be included depending on your particular area.
Please check with your Yamaha dealer.
 DTX700/DTX900M Owner's Manual (x1)
 DTX700/DTX900M Data List (x1)
Assembling the tom pads
2.
Push the tom pads onto the rack's clamp rods. Ensure
XP100T
that the rod section is fully inserted into the each pad's
mounting hole, and then tighten the clamp bolt to se-
cure the pad in place.
Tom pad
Clamp bolt
XP120T
3.
Loosen clamp bolts A to E as shown below to adjust
the height and angle of any of the pads. When correct-
ly positioned, be sure to securely retighten the bolts
1.
Attach the clamp bolt to each of the tom pads and pro-
before proceeding to the next step.
visionally tighten (by 5 or 6 turns).
Clamp bolt (tighten in the
direction of the arrow)
Tom pad (rear side)
Clamp bolt A
Clamp bolt C
Continued on other side
 XP120T
Tom Pad (x1)
 HS740A
Hi-hat Stand (x1)
 Module holder screw
(x4)
Clamp rod
Rod section
Insert
Clamp bolt B
Clamp bolt D
Clamp bolt E