Advertisement
Programmable Features:
Features
1 Chirp
First
Passive Arming
Second
Ignition D/L ON
Third
Ignition D/UL ON
Fourth
Chirps ON
Fifth
Passive D/L
Sixth
Siren Output
Seventh
800ms D/L Pulse
To Program These Features:
Entering the Programming Mode involves operating the Ignition Switch and the Valet/Program/Manual Override Switch in
a particular sequence. This sequence is very time dependent; in other words it must be performed quickly in order for you
to enter the mode. This sequence is also only one step different from the Transmitter Programming Mode, so make
certain you perform the sequence properly.
Upon entering the Programming Mode, the system is immediately set to allow adjustment of the First Programmable
Feature. That First feature, "Passive or Active Arming", can then be set ON or OFF by pressing the lock button of the
transmitter. The system confirms that it is set to adjust the First feature by repeatedly flashing the LED once, with a pause
in between each flash. The system will then report how the feature has been set by the number of chirps heard after
pressing the transmitter button. Toggling the Valet/Program/Manual Override Switch once again will advance you to the
Second Programmable Feature, confirmed by a repeating two LED flashes, with a pause in between each flash, etc., etc.
It is important to note that when you first enter the Programming Mode, you are automatically positioned to adjust the First
Programmable Feature and that the Valet/Program/Manual Override Switch allows you to toggle from there through each
of the six more programmable features. However, it will not allow you to return to any feature once you have toggled past
it. Should you accidentally toggle past the feature you wanted to program, you must exit and re-enter the Programming
Mode and then adjust the feature you missed.
It is also important to note that you may toggle past as many programmable features as you wish without having to adjust
them. Each time you toggle forward to a new feature, the horn will chirp the appropriate number of times (1, 2, or 3 times)
to indicate how that feature is currently set, and the LED will flash the appropriate number of times to indicate the number
of the feature (First through Seventh) that you are set to adjust. For example, you might enter the mode and toggle the
Valet/Program/Manual Override Switch 3 times in order to adjust the Fourth programmable feature. The system would
respond with 1 Chirp, and the LED would begin to flash 4 Flashes, pause, and repeat. This has told you that the system is
ready for you to adjust the Fourth programmable feature, and that it is currently programmed for Chirps ON. A single press
of the lock button of the transmitter will cause the system to produce 2 Chirps. This signifies that you have changed the
programming to Chirps OFF. Please follow the programming procedure below, and refer to the list of the Programmable
Features above when programming the system.
To program these selectable features;
Action
Turn ignition on
Turn the valet switch on then off 3 times
Within 3 seconds, turn ignition Off
First
Then On
Press transmitter Lock button to change
or
Second Turn the valet switch on then off
Press transmitter Lock button to change
or
Third
Turn the valet switch on then off
Press transmitter Lock button to change
or
2 Chirp
Active Arming
Ignition D/L OFF
Ignition D/UL OFF
Chirps OFF
Active D/L
Horn Output
3.5 Sec. D/L Pulse
800ms D/L Pulse
Double 800ms D/UL Pulses
System Response
No response
1 Chirp - LED 1 flash
Short chirp, then long chirp
2 chirps = active arming
1 chirp = passive arming
2 chirps = auto locks off
1 chirp = auto locks on
2 chirps = auto unlock off
1 chirp = auto unlock on
6
3 Chirps
Active Arming
Ignition D/L OFF
Ignition D/UL OFF
Chirps ON
Active D/L
Horn Output
800ms Door Lock
Default
LED Response
1 Flash pause
2 Flash pause
3 Flash pause
128-6711
6 of 8
Advertisement
