Table of Contents
Advertisement
4 Button Remote Start Security System With
Plug-In Shock Sensor & Starter Disable
IMPORTANT ! In order to provide you with the highest level of security to your
vehicle, this system is equipped with selectable manual override circuitry. It is
possible that you will need to override you security system if the transmitter
becomes lost, or inoperative due to battery failure. Reading the sections on
"Manually Overriding Your System" is necessary to fully understand the procedure
required to enable your vehicle in such situations. In addition, the chart on the last
page of this manual has a section for the particular features and options installed
in your vehicle as well as the override method selected. Although the default
mode is "Valet Switch" operation, the system can be configured for "Custom
Code" operation for enhanced security. Confirm the override mode selected on
the last page of this manual, and familiarize yourself with the section on it's opera-
tion.
FEATURES :
! 1 Two Way 5 Button Remote Control And 1 One Way 5 Button Remote Control
! Six Channel Code Learning Programmable Receiver
! External Superheterodyne Transceiver Antenna
! Single Or Two User Programmable W/Separate Control Outputs
! Single Button Lock/Unlock or Separate Button Lock/Unlock or Both
! Remote Keyless Entry With Optional Access Guard (must have power door
locks)
! Selectable Manual Override Mode
! New Enhanced Panic Feature (Any button other than unlock stops siren, no
change to the units state)
! Smart Disarm (If triggered, elect to shut off siren, or disarm entire unit )
! Adjustable Shock Sensor Via The Transmitter (Pre-Detect Off, Pre & Full Detect
Off, City Mode)
! Safe Start Output Controlled From Channel 3 (Option Channel 3 For Trunk, Or
For R/S)
! 24 Hour Time Start Mode
! Cold Temperature Start Mode
! 2 or 4 Hour Automatic Start Mode
! Parking Meter Count Down Timer On LCD Remote
! Additional Count Down Timer Mode
! Remote Panic In All Modes (Press & Hold Lock /Unlock Button For 3 Seconds
To Engage)
! Improved Custom Code Override, User Selectable and Programmable
Model APS-997
Owner's Manual
Page 1
128-7401
1 of 24
Advertisement
Table of Contents
Related Manuals for Audiovox Patinum APS-997
Summary of Contents for Audiovox Patinum APS-997
- Page 1 4 Button Remote Start Security System With Plug-In Shock Sensor & Starter Disable IMPORTANT ! In order to provide you with the highest level of security to your vehicle, this system is equipped with selectable manual override circuitry. It is possible that you will need to override you security system if the transmitter becomes lost, or inoperative due to battery failure.
- Page 2 ! Protected Push Button Valet/Override Switch ! 7-Function LED-Arm / Disarm / Zone 1 / Zone 2 / Zone 3 / Valet / Arming ! Intrusion Alert With Memory ! Instant Siren Activation ! Starter Disable Output ! Additional Engine Immobilizer Output, (Optional Relay Required) ! True Last Door Arming (Hardwire Only) ! Defective Zone By-Pass ! Defective Zone Chirp Confirmation (Unit Chirps To Report Zone Cleared)
-
Page 3: Arming The System - Active
known as a code grabber, which will receive and store the signal from your keychain transmitter and re-transmit at a later time to disarm your system. Your Keeloq Code Hopping transmitters will change their signal every time the button is pressed, so when a thief grabs then re-transmits your signal, the alarm system will not respond. -
Page 4: Protection While The System Is Armed
" The dash mounted LED begins to flash slowly. " Parking Lights flash one time. " Siren will not sound. If the siren "chirped" three times, sometime after arming, the exclusive delayed dome light learn circuit has been programmed and the system detected a open entry point after the learned delay expired. -
Page 5: Disarming The System
started. " Any mild impact to the vehicle’s glass will cause the alarm to sound a short series of warning tones. " Any strong impact to the vehicle’s glass will cause the alarm to trigger for the full 30 second alarm cycle. NOTE: If the optional interior illumination circuit was installed, the interior light will flash as well for the full 30 second alarm cycle. -
Page 6: While The System Is Sounding
automatically. Open any door to suspend the automatic arming. " Parking Lights flash two times. If the parking lights flashed three times, then the alarm was triggered in your absence. Before turning the key on, examine the LED to identify which zone was triggered. -
Page 7: Programming Your Custom Override Code
LED turns on solid. The system will remain in the valet mode. 3. To return to normal operation, press and release the pushbutton switch any time the ignition is on. NOTE: Always remember to return the system to normal operation. This will ensure that the vehicle remains protected at all times. -
Page 8: Eliminating The Normal Arm / Disarm Chirps
To Change the code from the factory pre-assigned code of 11 to “52” you would do the following: 1. Disarm the system by use of the transmitter or by use of the emergency override sequence. 2. Turn the ignition switch to the on position. 3. -
Page 9: Remote Panic Operation
1. Turn the ignition key on then off. 2. Within 10 seconds, press and release valet switch three times. 3. If the chirps were on before you started, then you will hear two chirps indicat- ing they have been turned off. If the chirps were off before you started, then you will hear one chirp indicating they have been turned on. -
Page 10: Remote Starting The Vehicle
In this mode, the pre-detect chirps will change from six pre-warning tones to a full 10 seconds of warning chirps. The full detect trigger duration will be reduced from 30 seconds to 15 seconds. NOTE: Setting the stage of the shock sensor will be effective for one arming cycle only. - Page 11 monoxide fumes which can be harmful or fatal if prolonged exposure occurs. DO NOT remote start the vehicle if it is garaged. To Remote Start The Vehicle: Press and release the programmed channel of your keychain transmitter two times within 2 seconds. The vehicle will start and remain running for the pre- programmed 5, 10, 15, or 20 minutes.
- Page 12 the second channel button of your keychain transmitter 4 times). The parking lights will flash and the siren will chirp 4 times indicating the timed start mode is activated. CANCELING THE AUTOMATIC START UP TIMER To cancel the automatic start up timer do one of the following; 1.
-
Page 13: Turbo Timer Mode
# Remote Car Starter # Remote Window Closure # Remote Garage Door Interface To remotely operate the device indicated, momentarily press, or press and hold the appropriate transmitter button(s) as indicated above. ADDITIONAL REMOTE FUNCTION ( CHANNEL 6 ) Channel 6 is an alternate output that can be controlled by the unlock button of the transmitter, or by and independent button or combination of buttons. -
Page 14: Telematic Upgrade
To activate the turbo timer: Anytime the engine is running for more than 15 seconds: 1) Place the the gear selector in park. 2) Set the parking, (hand), brake. 3) Be certain your foot is off the brake pedal. 4) Press the program/Push-Button switch 2 times within 5 seconds. The parking lights will flash two times indicating the mode was successfully entered. - Page 15 When the Key Icon Button is pressed 2 times in succession The three puffs of smoke are displayed on the LCD screen while the vehicle is running. The exhaust indication will flash and the hour glass will indicate count down timer based on the 5, 10, 15, or 20 minute run time set up by your installation center.
- Page 16 Triggered and entry attempt was made to the vehicles glass, or the vehicle has been hit or bumped hard enough to cause a response from the vibration detector. ADDITIONAL ICONS THAT MAY BE DISPLAYED ARE: If the arm/disarm chirp tones have been turned off at the ve- hicle, when you arm, or disarm, the display will indicate this as shown and there will be no arm/disarm chirps at the transmit- ter.
- Page 17 ADDITIONAL REMOTE FEATURES: The two way remote control unit allows you to access status information from the vehicle, check temperature, light the display, toggle the transmitter from beep tones to vibrate mode, initiate daily start timer, and temperature start. Selection of these and other features are shown below: NOTE: Transmitter must be within operating range of the vehicle, approximately 1000 ft.
- Page 18 Note this feature must be activated at the vehicle at the prescribed time. Once activated at the vehicle, you can toggle the feature on simultaneously pressing the Lock + Option buttons of the transmitter. The 24 hour icon will appear and the transmitter will emit a tone confirming the feature is active.
- Page 19 Battery Indicator: Your transmitter has a battery indicator that is shown in the upper right corner of the screen as shown left. This icon indicates a new battery shown with 3 bars. As the battery deteriorates, the bars will disap- pear.
- Page 20 THIS PAGE LEFT BLANK INTENTIONALLY Page 20 128-7401 20 of 24...
- Page 21 Page 21 128-7401 21 of 24...
- Page 22 THIS PAGE LEFT BLANK INTENTIONALLY Page 22 128-7401 22 of 24...
- Page 23 SYSTEM FUNCTIONS AT A GLANCE DASH LED INDICATORS RAPID FLASHING REARMING SLOW FLASHING ON SOLID 3 FLASH...PAUSE 2 FLASH...PAUSE 1 FLASH...PAUSE SIREN CHIRP INDICATORS 1 CHIRP * 2 CHIRPS * 3 CHIRPS 4 CHIRPS * These chirps are optional, and can be de - activated. PARKING LAMP INDICATORS 1 FLASH 2 FLASHES...
- Page 24 © 2005 Audiovox Electronics Corp., 150 Marcus Blvd., Hauppauge, NY 11788 128-7401 Page 24 128-7401 24 of 24...