Read this manual prior to initial operation of the product! Dear Customer, We hope that your product, which has been manufactured in modern facilities and passed through a strict quality control procedure, will give you very good results. We advise you to read through this manual carefully before using your product and keep it for future reference. This User Manual will •...
Important safety information This section includes safety information that will help plenty of detergent before being dried in the dryer. protection from risks of personal injuries or materialistic • Garments or pillows bolstered with rubber foam damages. Failure to follow these instructions shall cause (latex foam), shower bonnets, water resistant textiles, any warranty and reliability commitment to become void.
Compliance with the WEEE Directive and • The final step of the drying cycle (cool-down cycle) occurs without applying heat to ensure that the items Disposing of the Waste Product: are left at a temperature that will not damage them. This product complies with EU WEEE •...
Installation Refer to the nearest Authorised Service Agent for Make sure that you have removed the transportation installation of your product. safety assembly (nylon+styrofoam pieces) before using the product for the first time. Do not leave any items Preparation of location and electrical installation for inside the drum.
First use 1. Remove the hose on the machine by pulling it out from its end. Do not use any tools to take out the hose. • To have the product ready for operation before 2. Connect the special drain hose supplied with the calling the authorised service agent, make sure machine to the pipe fitting.
Technical specification Height (adjustable) 84.6 cm Width 59.5 cm Depth 59.8 cm Capacity (max.) 8 kg Weight (net) 38 kg Voltage Rated power input See type label Model code Type label is located behind the loading door.
Initial preparations for drying hings to be done for energy saving: Laundry unsuitable for drying in the • Make sure that you operate the product at its full machine capacity but pay attention to not exceeding it. • Laundry items with metal attachments such as belt •...
• Sort your laundry according to their types and Following weights are given as examples. thicknesses. Dry the same type of laundry together. Approximate E.g.: fine kitchen towels and table cloths dry faster Home articles weights (g) than the thick bath towels. Correct load capacity Cotton quit covers (double) 1500...
Loading the laundry 1. Open the loading door. 2. Place the laundry in the machine without compressing. 3. Push the loading door to close. Ensure that no items are caught in the door.
Selecting a Programme and Operating Your Machine Control panel 5. Programme selection knob 1. Filter cleaning warning light Used to select a programme. Warning light turns on when the filter is full. 6. Start/Pause/Cancel button 2. Program follow-up indicator Used to start, pause or cancel the programme. Used to follow-up the progress of the current 7.
Preparing the machine •Anti-creasing A 2-hour anti creasing programme to prevent laundry 1. Plug in your machine. from creasing will be activated if you do not take the 2. Place the laundry in the machine. laundry out after the programme is over. This programme 3.
Program selection and consumption table Approximate Spin speed in washing Drying time Programmes Capacity (kg) amount of machine (rpm) (minutes) remaining humidity Cottons / Coloreds Cupboard dry 1000 % 60 Cupboard dry plus 1000 % 60 Iron dry 1000 % 60 Xpress 35’...
Page 14
Water tank “Cupboard dry”: Warning light starts flashing when the tank is filled with Starts to illuminate when the drying degree reaches water. The dryer stops operating if the warning light turns “Ready to wear” step and remains illuminated until the next step.
Ending the programme through canceling Laundry may be added or taken out as much as To cancel any selected programme: desired during a drying process, but this process will Press “Start/Pause/Cancel” button for about 3 seconds. extend the programme duration and increase energy consumption since the drying will be interrupted The “Filter cleaning”, “Water tank”...
Maintenance and cleaning Filter Cartridge / Door Inner Surface Lint and fibres released from the laundry to the air during the drying cycle are collected in the “Filter Cartridge”. Sensor Such fibre and lint are generally formed during wearing and washing. Always clean the filter and the inner surfaces of the cover after each drying process.
Water tank; For the condenser; The moisture in the damp laundry is taken from the Hot and humid air in the condenser is cooled with the laundry and condens ed. Drain the water tank after each cold air from the room. Thus, the humid air circulating in drying cycle or during drying when “Water tank”...
Page 18
4. Clean the condenser by applying pressurized water with a shower armature and wait until the water drains. 5. Place the condenser in its housing. Fasten the 2 locks and make sure that they are seated securely. 6. Close the kick plate cover.
Suggested solutions for problems Drying process takes too much time • Meshes of the filter may be clogged. Wash with water Laundry comes out wet at the end of drying. • Meshes of the filter may be clogged. Wash with water. •...