Setting Rear View Camera Activation; Setting The Polarity Of The Rear View Camera - Pioneer AVH-X8890BT Owner's Manual

System settings
Camera View mode also allows you to check what is behind you
while driving.
Camera for Camera View mode
Camera View can be displayed at all times. Please note that
with this setting, the camera image is not resized to fit, and that
a portion of what is seen by the camera is not viewable.
To display the camera image, touch [Camera View] on the AV
source selection screen.
 Refer to Source on the AV source selection screen on page
11
p To set the rear view camera as the camera for Camera View
mode, set "Back Camera Input" to "On".
p When using the 2nd camera, set "AV Input" to "Camera".
CAUTION
Check to make sure settings for rear view camera displays a
mirror reversed image.
p Immediately verify whether the display changes to a
rear view camera image when the gearstick is moved to
REVERSE (R) from another position.
p When the screen changes to full-screen rear view camera
image during normal driving, switch to the opposite setting
in "Reverse Gear Setting.".
p If you touch while the camera image is displayed, the
displayed image will turn off temporarily.
p When the camera view of both the rear view camera and 2nd
camera are available, the key to switch the display appears.
Touch this key to switch the display between the rear view
image and 2nd camera image.

Setting rear view camera activation

The default setting is "Off".
1 Display the "System" setting screen.
 Refer to Displaying the "System" setting screen on page
37
2 Touch [Camera settings].
3 Touch [Back Camera Input] to switch "On" or
"Off".
Setting the polarity of the rear view
camera
The default setting is "Battery".
1 Display the "System" setting screen.
 Refer to Displaying the "System" setting screen on page
37
38
2 Touch [Camera settings].
3 Touch [Reverse Gear Setting.].
 Battery:
The polarity of the connected lead is positive.

Ground:
The polarity of the connected lead is negative.
p If no camera connection is made and the camera polarity
setting is wrong, a black screen is displayed as the rear view
camera image immediately after startup. In such a case,
press and hold the MUTE button to release the rear view
camera screen and then change the camera polarity setting
to "Battery".
Setting the reversed image display
for the rear view image
You can set whether to reverse the rear view camera images to
be displayed on the front screen.
The default setting is "Off".
p This setting is available only when you stop your vehicle in a
safe place and apply the handbrake.
p This function is available when "Back Camera Input" is set
to "On".
 Refer to Setting rear view camera activation on page 38
1 Display the "System" setting screen.
 Refer to Displaying the "System" setting screen on page
37
2 Touch [Camera settings].
3 Touch [Back Camera: Reverse Video] to switch
"On" or "Off".
Setting the parking assist guidelines
Displaying the parking assist
guidelines
You can set whether to display the parking assist guidelines on
the rear view camera images when backing up your vehicle.
The default setting is "Off".
1 Display the "System" setting screen.
 Refer to Displaying the "System" setting screen on page
37
2 Touch [Camera settings].
3 Touch [Parking Assist Guide] to switch "On" or
"Off".
Adjusting the parking assist
guidelines
CAUTION

When adjusting the guidelines, be sure to park the vehicle
in a safe place and apply the handbrake.
 Before getting out of the car to place the markings, be sure
to turn the ignition switch off (ACC OFF).
 The range projected by the rear view camera is limited.
Also, the vehicle width and distance guidelines displayed
on the rear view camera image may differ from the actual
vehicle width and distance. (The guidelines are straight
lines.)

The image quality may deteriorate depending on the usage
environment, such as at night or in dark surroundings.
1 Park your vehicle in a safe place and apply the
handbrake.
2 Using packing tape or similar, place markings
as follows.
2 m
50 cm
Markings
Markings
Rear bumper
3 Display the "System" setting screen.
 Refer to Displaying the "System" setting screen on page
37
4 Touch [Camera settings].
5 Touch [Parking Assist Guide Adjust].
6 Set the guidelines by dragging the four points.
Adjust the guidelines so that the guidelines can be overlaid to
the markings
p Touch / / / / / to adjust the guidelines if
necessary. Touch [Default] to reset the settings.
25 cm
25 cm