Table of Contents
Advertisement
Quick Links
08884
MODEL NO.
08885
MODEL NO.
®
SAND PRO
To understand this product, and for safety and
optimum performance, read this manual
before starting operation. Pay special attention
to SAFETY INSTRUCTIONS highlighted by
this symbol.
© The TORO Company 1997
70001
—
& OVER
70001
—
& OVER
®
2020 & 3020
FORM NO. 3319-143 GB
OPERATOR'S
MANUAL
Advertisement
Table of Contents
Related Manuals for Toro 08884
Summary of Contents for Toro 08884
- Page 1 & OVER ® ® SAND PRO 2020 & 3020 To understand this product, and for safety and optimum performance, read this manual before starting operation. Pay special attention to SAFETY INSTRUCTIONS highlighted by this symbol. © The TORO Company 1997...
-
Page 2: Table Of Contents
If help concerning set up, operation, maintenance or safety is ever needed, contact your local Authorized TORO Distributor. In addition to genuine TORO replacement parts, the distributor also has optional equipment for the com- plete line of TORO turf care equipment. Keep your Toro all TORO. Buy genuine TORO parts and accessories. Table of Contents... -
Page 3: Safety Instructions
Safety The SAND PRO was designed and tested to offer safe C. Do not smoke while handling gasoline. service when operated and maintained properly. D. Fill the fuel tank outdoors and to about one Although hazard control and accident prevention partial- inch below the top of the tank, (bottom of ly are dependent upon the design and configuration of filler neck). - Page 4 28. Do not overspeed the engine by changing governor settings. Maximum engine speed is 3200 rpm. To A. Engage the parking brake and lower the attach- assure safety and accuracy, have an Authorized Toro ment. Take precautions to prevent accidental Distributor check maximum engine speed with a starts, rolling away, etc.
-
Page 5: Symbol Glossary
Symbol Glossary... -
Page 6: Specifications
Specifications Configuration: Short-wheelbase tricycle vehicle with Optional Equipment: mid engine placement. Rear wheels powered. Front Drag Mat Model 08850 wheel steering. Operator positioned centrally. Rake Model No. 08811 Edger Kit Model No. 08822 Engine: Briggs & Stratton, V-twin cylinder, 4-cycle Rake Mounting Kit Model No.08814 OHV, air-cooled, gas engine with cast iron sleeves. -
Page 7: Before Operating
THE TORO COMPANY STRONGLY RECOMMENDS THE USE OF FRESH, CLEAN, UNLEADED REGU- The engine is shipped with 1.7 l (with filter) of oil in the LAR GRADE GASOLINE IN TORO GASOLINE crankcase; however, check the level before and after the POWERED PRODUCTS. UNLEADED GASOLINE engine is first started. -
Page 8: Check Hydraulic System
Before Operating Clean the area around the fuel tank cap. should be up to the top of the cone point on the tank screen. If the oil level is low, slowly fill the reservoir with appropriate hydraulic oil until the level is up to the top of cone point on the tank screen. -
Page 9: Know Your Controls
Controls Traction and Stopping Pedal (Fig. 4–5)—The traction tion pedal just barely depressed. pedal has three functions: one, to make the machine move forward, two, to move it backward and three, to CAUTION stop the machine. Using the heel and toe of your right foot, depress the top of the pedal to move forward and Use the maximum ground speed ONLY when driving bottom of the pedal to move backward or to assist in... -
Page 10: Operating Instructions
Controls control has two positions: SLOW and FAST. Engine NOTE: The SAND PRO has a double-acting lift cylin- speed can be varied between the two settings. der. Down pressure can be applied to the implement for certain operating conditions. Note: The engine cannot be stopped by the throttle con- trol. -
Page 11: Check Interlock System
In case of emergency, the SAND PRO can be towed for making sharp turns or when turning on hillsides. a short distance. However, Toro does not recommend Avoid sudden stops and starts. Do not go from reverse this as a standard procedure. -
Page 12: Maintenance
Maintenance Minimum Recommended Maintenance Intervals Maintenance Procedure Maintenance Interval & Service Check battery fluid level Every Every Every Check battery cable connections 400 hours 800 hours hours ✝ Change engine oil hours Lube front wheel bearing Lube traction control linkage Replace engine oil filter Inspect remote air filter element Inspect the engine air filter element... -
Page 13: Lubrication
Maintenance chain unless it becomes stiff because of rust. If the chain CAUTION rusts, it may be lubricated lightly with a DRY-TYPE lubricant. Before servicing or making adjustments to the machine, stop the engine and remove the key from the switch. LUBRICATION The Sand Pro has (3) grease fittings that must be lubri- cated regularly with No. -
Page 14: Servicing Air Cleaner
Maintenance the filter adapter, then tighten 1/2 to 3/4 turn further. Reinstall the air cleaner and cover plate. DO NOT OVER-TIGHTEN. Reinstall the air cleaner cover and secure it with the ADD OIL TO THE CRANKCASE. knobs. Dispose of oil properly. GENERAL AIR CLEANER MAINTE- NANCE SERVICING THE AIR CLEANER... -
Page 15: Adjusting Throttle Control
Maintenance C. Dry the filter element using warm, flowing air ADJUSTING THE CHOKE (160°F max), or allow element to air-dry. Do CONTROL not use compressed air or a light bulb to dry the filter element because damage could result. Pivot the seat upward. Compressed Air Method Loosen the cable clamp screw securing the cable to the engine. -
Page 16: Cleaning Cylinder Head Fins
8 hours of operation, and thereafter every voir, add oil if necessary. 400 hours of operation or yearly, whichever comes first. Use a genuine Toro oil filter for replacement. The 10. Check all connections for leaks. hydraulic oil must be changed every 400 hours of opera- tion or yearly, whichever comes first. -
Page 17: Battery Storage
Wear safety goggles and rubber gloves when working with electrolyte. Charge the battery in a To order replacement parts from an authorized TORO well ventilated place so gases produced while Distributor, supply the following information: charging can dissipate. -
Page 18: Warranty
January 1, 1997, to be free from defects in materials or workmanship for the period of time listed below. Where a warrantable condition exists, Toro will repair the Product at no cost to you including diagnosis, labor, parts, and transportation. This warranty begins on the date the Product is delivered to the original retail purchaser.