Samsung SCX-6555NX Series User Manual page 96

MESSAGE
Fuser error: [zzz]. There is a problem in
the fuser unit working.
Please turn off then
on
Fuser unit is not The fuser unit is not
installed or correctly.
installed correctly.
Install it
End of life, Replace The toner in the
imaging unit has run
with new imaging
out.
unit
Imaging unit is not The imaging unit you
have installed is not
compatible. Check
for your machine.
user's guide
Imaging unit is not The imaging unit is
not installed, or the
installed. Install it
CRUM (Consumer
Replaceable Unit
Monitor) in the
cartridge is not
connected.
Replace with new The imaging unit is at
the end of its life.
imaging unit
When the imaging unit
replacement message
appears on the screen
and if you select
Continue, this
message displays.
LSU error: [zzz]. There is a problem in
the control of LSU
Please turn off then
unit.
on
Motor does not There is a problem in
the control of motor
operate: [zzz].
unit.
Please turn off then
on
Original paper does The lead edge of the
document failed to
not feed in scanner
actuate the scan
sensor within the
correct time after
actuating the
registration sensor.
Downloaded From ManualsPrinter.com Manuals
SUGGESTED
MEANING
SOLUTIONS
Turn the machine off
and turn it on again. If
the problem persists,
please call for service.
Install the fuser unit.
Call for service.
Replace the imaging
unit with a Samsung-
genuine toner cartridge.
(See "In the multi-
purpose tray" on
page96)
Install a Samsung-
genuine imaging unit,
designed for your
machine.
Install the imaging unit.
If it is already installed,
try to reinstall the
imaging unit.
If the problem persists,
please call for service.
Replace a imaging unit
with a Samsung-
genuine imaging unit.
(See "In the multi-
purpose tray" on
page96)
Turn the machine off
and turn it on again. If
the problem persists,
please call for service.
Turn the machine off
and turn it on again. If
the problem persists,
please call for service.
Open the DADF cover
and remove jammed
original. (See "In the
multi-purpose tray" on
page96)
MESSAGE
Original paper is too Oversized document
or double-feeding of
long for scanner.
originals.
Check size
Original paper jam The originals are
jammed in DADF.
in front of scanner
Original paper jam Paper has jammed
during duplex printing
in front of scanner
in the DADF.
duplex path
Original paper jam The lead edge of the
document failed to
inside of scanner
actuate the gate
sensor within the
correct time after
actuating the scan
sensor.
When the machine is
on, jammed paper is
detected in the DADF.
Original paper jam The lead edge of the
document failed to
while reversing
actuate the duplex
paper in scanner
sensor within the
correct time when the
document was fed the
wrong way.
Paper jam at exit of Paper jammed in the
stacker exit part.
finisher
Paper Jam at the Paper has jammed
during duplex printing.
bottom of duplex
path
Paper Jam at the top
of duplex path
Paper Jam in exit Paper has jammed in
the fuser area.
area
Paper jam in front of Paper jammed in the
stacker.
finisher
Paper jam inside
finisher
Paper Jam in MP Paper Misfed from
multi-purpose tray
tray
96
SUGGESTED
MEANING
SOLUTIONS
Open the DADF cover
and remove the
jammed original. (See
"In the multi-purpose
tray" on page96)
Check the document
size whether it is
supported. (See "In the
multi-purpose tray" on
page96)
Open the DADF cover
and remove the
jammed original. (See
"In the multi-purpose
tray" on page96)
Clear the jam. (See "In
the multi-purpose
tray" on page96)
Open the DADF cover
and remove the
jammed original. (See
"In the multi-purpose
tray" on page96)
Lift up the document
input tray and remove
the jammed original.
(See "In the multi-
purpose tray" on
page96)
Pull jammed paper
from the stacker exit.
Clear the jam. (See "In
the multi-purpose
tray" on page96)
Clear the jam. (See "In
the multi-purpose
tray" on page96)
Open the stacker door
and remove jammed
paper by lowering
guide 1a or 1b.
Clear the jam. (See "In
the multi-purpose
tray" on page96)