Page 1
Classic™ I1200S Wood Insert Owners & Installation Manual www.regency-fire.com Tested by: Installer: Please complete the details on the back cover and leave this manual with the homeowner. Homeowner: Please keep these instructions for future reference. FPI FIREPLACE PRODUCTS INTERNATIONAL LTD. 6988 Venture St., Delta, BC Canada, V4G 1H4 919-538 09.14.15...
Page 2
The following statements are required by the Environmental Protection Agency: “This manual describes the installation and operation of the Regency I1200 wood heater. This heater meets the 2015 U.S.Environmental Protection Agency’s crib wood emission limits for wood heaters. Under specific test conditions this heater has been shown to deliver heat at rates ranging from 10,600 BTU/hr. to 34,700 BTU/hr.”...
I1200S Wood Insert. We have printed a copy of the contents here for your review. NOTE: Regency units are constantly being improved. Check the label on the unit and if there is a difference, the label on the unit is the correct one.
WITH STANDARD FLUE ADAPTOR 6" (152mm) Diameter STANDARD FLUE ADAPTOR (171-932) Regency Inserts are designed to use either a 5.5" (140mm) or 6" (152mm) flue. I1200 Regency Wood Insert...
1) Read all instructions before installing and must be supplied with appropriate supporting using your fireplace insert. Install and use means. Regency Inserts are designed to use either a only in accordance with manufacturer’s 5.5" (140mm) or 6" (152mm) flue. installation and operating instructions.
(m)(K) (hr)(ft)( R = 1/k x T = 1/0.84 x .75 = 0.893. specified R of 0.893. Since proposed system R is greater than required, the system is Thermal Resistance: acceptable. R = (ft )(hr)( )(K) I1200 Regency Wood Insert...
10) Re-install the door if removed prior to installation. Flue Adaptor Diagram 2 Secure adaptor using 3 screws - 1 in the Pull Rod In Place front and 1 each on the left and right side. Diagram 5 I1200 Regency Wood Insert...
The greater draft can decrease problems such as, difficult start-ups, Regency highly recommends the use of a full smoking out the door, and dirty glass. liner as the safest installation and provides the most optimum performance.
To replace the deflector, loosen off both bolts and slide defector upward and out. Install new defector and hand tighten bolts. Ensure positive location of the defector prior to hand tightening. WARNING: Operation of the unit with out proper installation of smoke deflector will void warranty. I1200 Regency Wood Insert...
I1200 installation FACEPLATE, TRIM, FAN & OPTIONAL FACEPLATE, TRIM & OPTIONAL BOTTOM FACEPLATE & FAN SUPPORT INSTALLATION BOTTOM FACEPLATE & FAN SUPPORT INSTALLATION Regular Faceplate Dimensions: Oversize Faceplate Dimensions: 12 | I1200 Regency Wood Insert 01/28/08 918-676c...
Page 13
Rear View Rear View Diagram 2 If the insert is going to sit on the hearth proceed to "Faceplate Trim Installation" Diagram 4 (step 8) otherwise continue on to "Bottom Faceplate Installation" (step 4). I1200 Regency Wood Insert 918-676c 01/28/08...
13) To install the optional fan support, measure the distance between the hearth and the bottom surface of the fan housing as shown in Diagram 8. Diagram 6: Shown with Optional Bottom Faceplate Diagram 8: Side View 14 | I1200 Regency Wood Insert 01/28/08 918-676c...
Page 15
Diagram 6. 22) Re-attach the fan/fan support assembly to the ash lip of the insert. Diagram 9: Rear / Bottom View Completed Faceplate Assembly I1200 Regency Wood Insert 918-676c 01/28/08...
3) Ensure that the power cord is not in contact Neutral Green Manual/ Live Ground Auto 120V AC Switch Switch 60 Hz Fan Thermodisc (normally open) Black Black Black Ground Blower / Fan Wiring Diagram 16 | I1200 Regency Wood Insert...
WARNING: To build a fire in ignorance or to disregard the informa tion contained in this section can cause serious permanent damage to the unit and void your warranty. Front View I1200 Regency Wood Insert...
Two dry pieces banged together sound hollow; wet pieces sound solid and dull. • Dry wood weighs much less than wet wood. • Split a piece of wood. If the exposed surface feels damp, the wood is too wet to burn. 18 | I1200 Regency Wood Insert...
Burn fires at a moderate level the first few days. 8) Do not place anything on the insert top during the curing process. This may result in damage to your paint finish. How to Light & Maintain a Wood Stove Fire I1200 Regency Wood Insert...
Removal of your insert for cleaning purposes is usually not required if a proper installation 9) Your Regency Insert can be very hot. You DO NOT ALLOW ASHES TO BUILD UP TO has been done. In the event that removal is re- may be seriously burned if you touch the THE LOADING DOORS.
GLASS REPLACEMENT DOOR GASKET Your Regency Insert is supplied with 5 mm. Neoceram ceramic glass that will withstand If the door gasket requires replacement, 7/8" the highest heat that your unit will produce. In diameter material must be used.
Faceplate Top Regular / Oversize 171-928 Bottom Piece and Fan Support - Regular 64) * Bottom 1 Piece Faceplate 65) * Fan Support 171-930 Bottom Piece and Fan Support - Oversize *Not available as a replacement part. I1200 Regency Wood Insert...
Brick Partial: 1-1/4" x 2" x 9" 81) * Brick Partial: 1-1/4" x 1-1/4" x 9" 84) * Brick Partial: 1-1/4" x 4-1/2" x 8" 85) * Brick Partial: 1-1/4" x 4-1/4" x 8" *Not available as a replacement part. 24 | I1200 Regency Wood Insert...
It is the general practice of FPI to charge for larger, higher priced replacement parts and issue credit once the replaced component has been returned to FPI and evaluated for manufacturer defect. The authorized selling dealer is responsible for all in-field service work carried out on your Regency product. FPI will not be liable for results or costs of workmanship from unauthorized service persons or dealers.