1. Manuals
  2. Brands
  3. Pioneer Manuals
  4. Car Video System
  5. AVIC-F860BT
  6. Installation manual

Pioneer AVIC-F860BT Installation Manual

Hide thumbs Also See for AVIC-F860BT:
Table of Contents

Advertisement

Quick Links

See also: Operating Manual
S
u
b
a
r
u
F
S
u
b
a
r
u
F
Pioneer AVIC-F860BT

Installation guide

Mike Haseler, Pioneer NV
Version 1.0 14/07/2014
Installation guide V1.0
Subaru Forester/ XV/ STI MY15
Pioneer AVIC-F860BT
o
r
e
s
t
e
r
/
o
r
e
s
t
e
r
/
X
V
/
S
T
I
X
V
/
S
T
I
Pages: 1 / 28
M
Y
1
5
M
Y
1
5

Advertisement

Table of Contents
loading

Related Manuals for Pioneer AVIC-F860BT

Summary of Contents for Pioneer AVIC-F860BT

  • Page 1: Installation Guide

    Installation guide V1.0 Pages: 1 / 28 Subaru Forester/ XV/ STI MY15 Pioneer AVIC-F860BT Pioneer AVIC-F860BT Installation guide Mike Haseler, Pioneer NV Version 1.0 14/07/2014...

  • Page 2: Table Of Contents

    Installation guide V1.0 Pages: 2 / 28 Subaru Forester/ XV/ STI MY15 Pioneer AVIC-F860BT Contents Pioneer AVIC-F860BT ................3 Introduction ................... 3 Partslist....................3 Tools required:..................4 Consumables: ..................4 Build instructions ................5 Unpacking ................... 5 Cable Preperation ................. 6 Vehicle strip down ................

  • Page 3: Pioneer Avic-F860Bt

    2, 1.5m Aux Extension cable 10x Cable Ties, 6 x Adhesive pads, 1 x M/F Bullet Crimps, 1 x 4.8mm M/F Spade CA-SPP.001 Small Parts Pack Crimps, 8 x PH Cutting Screws, 1 x Large Cable Tie. Mike Haseler, Pioneer NV Version 1.0 14/07/2014...

  • Page 4: Tools Required

    -1 x rubber grommet, -10 x self adhesive pads, -3 x microphone cable clamps, -Loom tape, -adhesive promoter, Dispose of supplied: Female bullet crimp connector, Female and male spade crimp connector, 8 x screws. Mike Haseler, Pioneer NV Version 1.0 14/07/2014...

  • Page 5: Build Instructions

    - Non UK quick start guide - 6 x countersunk screws, (not the 6 screws Panhead screws in the bag, as you will need them) - Power harness - 1 x USB extension - Cage Keep Discard Mike Haseler, Pioneer NV Version 1.0 14/07/2014...

  • Page 6: Cable Preperation

    65cm 65cm Make sure you leave a 65cm tail to the microphone right angled jack plug and then cable tie the excess bunch as shown. Mike Haseler, Pioneer NV Version 1.0 14/07/2014...
  • Page 7 Then secure excess by putting two cable ties on the ends. Don’t forget to put the instruction manual with CD etc into the glove box. Mike Haseler, Pioneer NV Version 1.0 14/07/2014...

  • Page 8: Vehicle Strip Down

    2.3 Vehicle strip down Ensure ignition is not operated during installation and is switched off prior to performing any installation work. Remove Radio Bezel with suitable trim tool and unclip any Loom connections Mike Haseler, Pioneer NV Version 1.0 14/07/2014...
  • Page 9 Remove 6 x PH2 screws to remove radio. Disconnect radio harnesses, remove radio from dash. Disconnect all wire harness from the radio. Remove instrument cluster bezel 2 x PH2 screws then the 3x instrument cluster screws. Mike Haseler, Pioneer NV Version 1.0 14/07/2014...
  • Page 10 Carefully, begin to unclip the gear gaiter Housing trim from the back. This should loosen the silver plastic trim pieces Using a trim tool, carefully unclip and remove the 2 silver trim pieces. Mike Haseler, Pioneer NV Version 1.0 14/07/2014...
  • Page 11 2 uncovered screws securing the rear arm rest section in place Slide both seats forward and remove the screw caps from the rear of the armrest section, Remove uncovered 10mm bolts either side of the arm rest Mike Haseler, Pioneer NV Version 1.0 14/07/2014...
  • Page 12 Pivot the Arm rest section backwards to gain access to the underside of it. Remove all plugs and cable clips from underneath. With rest section free, remove it from the vehicle and store safely Mike Haseler, Pioneer NV Version 1.0 14/07/2014...
  • Page 13 Fold over the original USB and AUX cables cable against adjacent harness to secure STI Armrest Carefully, unclip remove handbrake gaiter. Remove the concealed screw Remove Phillips screws underneath the carpet cover in the armrest storage pocket Mike Haseler, Pioneer NV Version 1.0 14/07/2014...
  • Page 14 Unscrew and remove the gear knob Using suitable trim tool, carefully unclip the gear surround trim. Once free, remove the surround and store safely. Mike Haseler, Pioneer NV Version 1.0 14/07/2014...

  • Page 15: Installation

    CAN IF AUX extension harness. Pass AUX extension harness up to the instrument cluster aperture as shown. Using the one large cable tie, secure the AUX harness under the dash as shown. Mike Haseler, Pioneer NV Version 1.0 14/07/2014...
  • Page 16 Feed the GPS antenna green plug to the radio aperture. Place excess Microphone bunch to the left of the instrument cluster aperture as shown. Feed the right angled jack to the radio aperture. Mike Haseler, Pioneer NV Version 1.0 14/07/2014...
  • Page 17 Note: Pass microphone capsule through the centre opening of the fabric dust guard above steering column the dust guard should sit over the cable Fully extend and lower steering wheel position Mike Haseler, Pioneer NV Version 1.0 14/07/2014...
  • Page 18 Microphone cable to the rear and bottom of the instrument cluster Using a plastic cleaner, clean the top of the instrument cluster, then adhere the GPS antenna ground plate to top of instrument cluster as shown. Mike Haseler, Pioneer NV Version 1.0 14/07/2014...
  • Page 19 Care point: Mount instrument cluster ensuring the microphone cable is located centrally under the cluster Replace the removed instrument cluster screws, bezel and bezel screws. Centrally mount the microphone if you have not already. Mike Haseler, Pioneer NV Version 1.0 14/07/2014...
  • Page 20 Connect Pink from CAN Option Harness to Pink Speed Pulse input. Connect Violet cable Violet/White (reverse input). The Park Brake cable is pre-wired, and is triggered when the vehicle speed reduces below 8KPH Mike Haseler, Pioneer NV Version 1.0 14/07/2014...
  • Page 21 Clip the plate into the front of the port and allow for the glue to cure Feed USB extension and AUX cable Mike Haseler, Pioneer NV Version 1.0 14/07/2014...
  • Page 22 Cable tie cables to conduit to secure. Refit the Modified Port into the port hole in the armrest Locate the centre console and begin to offer the console back into position. Connect the USB extension and Mike Haseler, Pioneer NV Version 1.0 14/07/2014...
  • Page 23 Port, then use the second to extend the length. The cable setup should follow this USB cable format. To stereo To stereo AUX Port Cable tie any excess USB/AUX cable into a bunch. Mike Haseler, Pioneer NV Version 1.0 14/07/2014...
  • Page 24 With both brackets loosely mounted, Slide both brackets back on the headunit so that the fascia sits flush and even against the headunit. Tighten the brackets in place. Mike Haseler, Pioneer NV Version 1.0 14/07/2014...

  • Page 25: Navigation Unit Final Installation

    4 AUX cable 5 Radio antenna 6 Microphone lead 7 Steering remote jack 8 Reverse camera Mount Navi unit into radio aperture using the 4x factory radio mounting screws. Refit radio surround connections and panel. Mike Haseler, Pioneer NV Version 1.0 14/07/2014...

  • Page 26: System Setup

    Put on the head lights. Screen dims and “On” is displayed= OK Check handbrake The Handbrake is triggered from speed pulse information, When the vehicle speed drops below 8km/h hand brake status will show as "on" Mike Haseler, Pioneer NV Version 1.0 14/07/2014...
  • Page 27 Set Voice Language as "English (UK) , TTS v4" "Units Formats" screen, ensure Distance is set to "Miles/Yards", Fuel economy is set to "MPG(UK)" Route Preferences settings can be left as default. Mike Haseler, Pioneer NV Version 1.0 14/07/2014...
  • Page 28 Select the seating position, i.e. "Front Right" press start Shut doors, windows. Wait till complete. Set audio source to FM Home, Settings, sound, Balance/Fader Set Fader rear by 6 Remove mic Remove Micro SD card Mike Haseler, Pioneer NV Version 1.0 14/07/2014...

Table of Contents