Using Your Cleaner; Cleaner Maintenance - Hoover SE71WR01 Instruction Manual

USING YOUR CLEANER

1. Extract power cord and plug it into the power supply. [5] Do not pull the cord beyond
the red marker.
Carpet & Floor Nozzle. Press the floor type selector pedal on the nozzle [6] to select
2.
the ideal cleaning mode for the floor type.
Hard Floor – Brushes are lowered to protect the floor.
Carpet – Brushes are raised for the deepest clean.
3. Switch the cleaner on by pressing the On/Off button on the cleaner main body. [7]
Switch off at the end of use by pressing the On/Off button. [7] Unplug and press the
4.
cord rewind button to wind the power cord back into the cleaner. [8]
5. To store your cleaner, park the nozzle in the parking slot at the rear of the cleaner
main body. [9] If the cleaner has the telescopic tube*, adjust it to the lowest height
setting and park the nozzle in the parking slot at the rear of the cleaner main body.
During usage and if your cleaner is equipped you can:
A. Adjust the telescopic tube* to the desired height by moving the telescopic tube
adjuster up and raise or lower the handle to the most comfortable cleaning po-
sition. [10]
B. Adjust the power level by rotating the Variable Power Control Knob* to the de-
sired level. [11]
C. Vary the suction as desired by closing or opening the suction regulator on the
hose handle. [12]

CLEANER MAINTENANCE

Emptying the Dust Container
When the dust reaches the max level indicator on the container, empty the dust
container.
IMPORTANT: To maintain optimum performance, do not allow the dust to sit higher than
the max level.
1. Release the Dust Container by pressing the Dust Container Release Button and
remove the Dust Container from the cleaner main body. [13]
2. Before emptying the Dust Container, gently tap it against the side of a bin to
release any excess dust from the filter.
3. To empty the Dust Container, hold the Dust Container over a bin with one hand and
use the other hand to press the Dust Container Flap Opening Button to release the
dust into the bin. [14]
4. Close the Dust Container Flap and refit the Dust Container to the cleaner main
body.
(*Certain Models Only)
4800XXXX - Sprint - Multi 5lang IM.indd 2
Cleaning the Washable Filters
The cleaner is fitted with a pre-motor filter. To maintain optimum cleaning performance,
regularly clean the filters. Remove excess dust from the filters by gently tapping them
against the side of a bin. The filters should be washed after every 5 container empties.
IMPORTANT: Regularly check and maintain the filters.
IMPORTANT: Always ensure the filter packs are fully dry before use.
To access the pre-motor filter:
Empty the Dust Container as described in 'Emptying the Dust Container'. Then, keeping
the Dust Container Flap open:
1. Remove the pre-motor filter by rotating it anti-clockwise at the bottom of the Dust
Container. [15]
2. Separate the protective mesh from the filter. [16] Gently tap both the protective
mesh and the filter against the side of a bin to remove excess dust and wash both
of them under warm water. [17] Do not use hot water or detergents.
3. Remove excess water from the filter and leave it to dry fully before reusing. [20]
4. Once the filter is fully dry, reassemble the filter pack (protective mesh and filter) and
refit to cleaner.
IMPORTANT: Do not use the product without the pre-motor filter pack fitted.
To access the exhaust filter:
1. Unclip the exhaust grid from the rear of the cleaner. [18]
Separate the filter from the grid and wash the filter under warm water. [19] Do not
2.
use hot water or detergents.
3. Remove excess water from the filter and leave to dry fully before reusing. [20]
4. Remount the filter into the grid and refit it to the cleaner.
Remember: Do not use hot water or detergents. In the unlikely event of the filters
becoming damaged, fit a Genuine Hoover consumable. Do not try and use the product
without a filter fitted.
2
GB
24/09/2010 01:15:12