Advertisement
Available languages
Available languages
Regulator / LP Gas Tank Connection
1. Make 2-3 oz. of leak detection solution by mixing
one part liquid dishwashing soap with three parts
water.
2. Make sure control knob is "OFF" (Figure 1).
3. Spoon several drops of solution, or use squirt
bottle, at the LP gas tank to regulator connection
(Figure 4).
4. Inspect the solution at the connection, looking
for bubbles.
a. If any bubbles appear, remove the LP gas tank
and reconnect, making sure the connection
is secure.
b. If you continue to see bubbles after several
attempts, remove the LP gas tank per
"Disconnecting LP Gas Tank" section, and
contact 1.800.762.1142 for assistance.
c. If no bubbles appear after one minute, turn
control knob to the "OFF" position, wipe away
solution and proceed.
Lighting
W WARNING: Do NOT expose this lantern to
flammable vapors or liquids during lighting.
1. Make sure all labels, packaging and protective
films have been removed from this lantern.
2. Make sure there are no obstructions of airflow to
the gas unit. Spiders and insects can nest within
and clog the burner/venturi tube at the orifice.
A clogged burner tube can lead to a fire.
3. Control knobs must be in the "OFF" position
(Figure 1).
4. Attach the LP gas tank per the "Connecting LP Gas
Tank" instructions.
5. For new mantels only: wearing heat-resistant
gloves, position a long lit match or long lit butane
lighter evenly under each mantle (Figure 5).
a. Hold match/lighter next to each mantle until
nothing but white ash remains.
b. Remove match/lighter.
Note: Once the mantles has been burned, it is
very fragile. Be careful not to touch it.
6. Previously burned mantels only: Wearing heat-
resistant gloves, position the match/lighter near
the side of the mantles (Figure 5).
a. Turn control knob counterclockwise to "ON."
b. Hold match/lighter next to mantle for up to 5
While Lantern is OFF and Fully Cooled
seconds.
1. The LP gas tank must be removed and stored
c. Remove match/lighter.
properly.
d. Repeat steps b - c for other mantle.
2. Once this lantern is cooled, place this lantern and
7. If ignition does not occur in 5 seconds, turn burner
base in a plastic bag and secure the bag with
control knob "OFF," wait 5 minutes and repeat
a string.
lighting procedure.
W WARNING: Do NOT completely seal the
Note: Once the mantle has been burned, it is very
plastic bag.
fragile. Be careful not to touch it.
W CAUTION: If burner flame goes out during
Note: The plastic bag will help protect from insects.
operation, immediately turn the gas "OFF"
and let the gas clear for about 5 minutes
Replace Mantle
before re-lighting.
1. Turn control knob to "OFF" and remove LP
Turning Off
gas tank.
1. Turn control knobs to the "OFF" position.
2. Remove Cap and Globe
2. Remove the LP gas tank per the "Disconnecting
LP Gas Tank" instructions.
Transporting
While Lantern is ON
1. Carefully carry this lantern by the handle while
wearing heat-resistant gloves.
2. Do NOT touch any of this lantern surfaces as they
may be hot.
3. Before setting this lantern down, make sure the
tank is properly in the base.
English – 4
3. Replace Mantles
Figure 1
Figure 2
4. Attach Globe and Cap
Figure 3
5. Perform Leak Check
Cleaning and Care
W CAUTION: All cleaning and maintenance
Figure 4
should be done when lantern is cool and
with the fuel supply disconnected.
W CAUTION: Do NOT clean any lantern part in
a self-cleaning oven. The extreme heat will
damage the finish.
W CAUTION: Keep lantern clear and free from
combustible materials, gasoline, and other
flammable vapours and liquids.
W CAUTION: Do NOT obstruct the flow of
Figure 5
combustion and ventilation air.
Notices
1. Abrasive cleaners will damage this product.
2. Never use oven cleaner to clean any part of
lantern.
Inspecting
This lantern should be inspected on a regular basis to
Match
ensure product safety and longer product life.
W WARNING: Do NOT attempt to inspect this
lantern unless the flames are COMPLETELY
out and unit is cool to the touch.
1. Check burner to make sure it is secure.
2. Check burner/venturi tube to make sure it is clear
and free of spider nests.
3. Check all gas connections for leaks.
4. Check components for any signs of damage or
rust.
5. If damage to any component is detected, do NOT
operate until repairs are executed.
Cleaning Surfaces
W WARNING: Do NOT attempt to clean this
lantern unless the flames are COMPLETELY
out and unit is cool to the touch.
W WARNING: Do NOT use oven cleaner or
abrasive cleaners as they will damage this
product.
1. Wipe surfaces clean with mild dishwashing
detergent or baking soda mixed with water.
2. For stained surfaces use a citrus-based degreaser
and a nylon scrubbing brush.
3. Rinse clean with water.
4. Allow to air dry.
Product Registration
For faster warranty service, register your product
immediately at BlueRhino.com/warranty or by calling
1.800.762.1142.
Replacement Parts
Replacement parts can be found at parts.BlueRhino.
com or by calling 1.800.762.1142.
Limited Warranty
Blue Rhino Global Sourcing, Inc. ("Blue Rhino")
warrants to the original retail purchaser of this
product, and to no other person, that if this product is
assembled, maintained, and operated in accordance
with the printed instructions accompanying it, then
for a period of one (1) year from the date of purchase,
all parts in such product shall be free from defects
in material and workmanship. Blue Rhino may
require reasonable proof of your date of purchase.
Therefore, you should retain your sales slip or invoice.
This Limited Warranty shall be limited to the repair
or replacement of parts, which prove defective
under normal use and service and which Blue Rhino
shall determine in its reasonable discretion upon
examination to be defective. Before returning any
parts, you should contact Blue Rhino's Customer
Service Department using the contact information
listed below. If Blue Rhino confi rms, after examination,
a defect covered by this Limited Warranty in any
returned part, and if Blue Rhino approves the claim,
Blue Rhino will replace such defective part without
charge. If you return defective parts, transportation
charges must be prepaid by you. Blue Rhino will return
replacement parts to the original retail purchaser,
freight or postage prepaid.
This Limited Warranty does not cover any failures or
operating diffi culties due to accident, abuse, misuse,
alteration, misapplication, improper installation or
improper maintenance or service by you or any
third party, or failure to perform normal and routine
maintenance on the product as set out in this owner's
manual. In addition, the Limited Warranty does not
cover damage to the fi nish, such as scratches, dents,
discoloration, rust or other weather damage, after
purchase.
This Limited Warranty is in lieu of all other express
warranties. Blue Rhino disclaims all warranties for
products that are purchased from sellers other than
authorized retailers or distributors, including the
warranty of merchantability or the warranty of fi tness
for a particular purpose. BLUE RHINO ALSO DISCLAIMS
ANY AND ALL IMPLIED WARRANTIES, INCLUDING
WITHOUT LIMITATION THE IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR
PURPOSE. BLUE RHINO SHALL HAVE NO LIABILITY TO
PURCHASER OR ANY THIRD PARTY FOR ANY SPECIAL,
INDIRECT, PUNITIVE, INCIDENTAL, OR CONSEQUENTIAL
DAMAGES. Blue Rhino further disclaims any implied
or express warranty of, and assumes no responsibility
for, defects in workmanship caused by third parties.
This Limited Warranty gives the purchaser specifi c
legal rights; a purchaser may have other rights
depending upon where he or she lives. Some
jurisdictions do not allow the exclusion or limitation
of special, incidental or consequential damages, or
limitations on how long a warranty lasts, so the above
exclusion and limitations may not apply to everyone.
Blue Rhino does not authorize any person or company
to assume for it any other obligation or liability in
connection with the sale, installation, use, removal,
return, or replacement of its equipment, and no such
representations are binding on Blue Rhino.
Blue Rhino Global Sourcing, Inc.
Winston-Salem, North Carolina 27105 USA
1.800.762.1142
Troubleshooting
Please visit BlueRhino.com or call 1.800.762.1142.
English – 5
Advertisement
