Residual Risks; Package Contents; Electrical Safety; Mains Plug Replacement - DeWalt DW713 Instruction Manual

EN G LI S H
• Connect the saw to a dust collection device when sawing wood.
Always consider factors which influence exposure of dust such as:
-– type of material to be machined (chip board produces more
dust than wood);
-– sharpness of the saw blade;
-– correct adjustment of the saw blade.
Ensure that the local extraction as well as hoods, baffles and
chutes are properly adjusted.
• Please be aware of the following factors influencing exposure
to noise:
-– use saw blades designed to reduce the emitted noise;
-– use only well sharpened saw blades;
• Machine maintenance shall be conducted periodically;
• Machine faults, including guards or saw blade, shall be reported as
soon as they are discovered;
• Provide adequate general or localized lighting;
• Ensure the operator is adequately trained in the use, adjustment
and operation of the machine;
• When fitted with laser, DO NOT change to a different type of laser.
Repairs shall only be carried out by the laser manufacturer or an
authorized agent.

Residual Risks

The following risks are inherent to the use of saws:
– injuries caused by touching the rotating parts
In spite of the application of the relevant safety regulations and the
implementation of safety devices, certain residual risks cannot be
avoided. These are:
– Impairment of hearing.
– Risk of accidents caused by the uncovered parts of the rotating
saw blade.
– Risk of injury when changing the blade.
– Risk of squeezing fingers when opening the guards.
– Health hazards caused by breathing dust developed when sawing
wood, especially oak, beech and MDF.

Package Contents

The package contains:
1 Mitre Saw
1 Blade wrench stored in wrench pocket
1 Saw blade
1 Dust bag
1 LED Worklight System (DW713XPS)
1 Instruction manual
1 Exploded drawing
• Check for damage to the tool, parts or accessories which may
have occurred during transport.
• Take the time to thoroughly read and understand this manual prior
to operation.
Description (fi g. 1, 2)
WARNING: Never modify the power tool or any part of it.
Damage or personal injury could result.
INTENDED USE
Your DW713/DW713XPS mitre saw has been designed for professional
cutting of wood, wood products and plastics. It will perform the sawing
operations of cross-cutting, bevelling and mitring easily, accurately and
safely.
The DW713/DW713XPS mitre saw is a professional power tool. DO
NOT let children come into contact with the tool. Supervision is required
when inexperienced operators use this tool.
a. Operating handle
b. Lower guard
c. Right side, fence
d. Table
28
e. Mitre lock lever
f. Mitre scale
g. Base
h. Holes for extension kit
i. Wrench
j. Bench mounting holes
k. Fence clamping knob
l. On/Off switch
m. Carrying handle
n. Dust spout
o. Lock down pin
p. Bevel clamp knob
q. Bevel scale
r. Hand indentation
s. Kerf plate
t. Mitre detent
v. left side, fence
w. Motor housing
x. Spindle lock
y. Hole for padlock
z. Angle position stop
aa. Bevel position adjustment stop
bb. Vertical position adjustment stop
cc. Head lock up lever
dd. Rear lower guard
ee. Upper guard
Optional Accessories (fi g. 3)
ff. Dust bag
gg. Clamp
hh. Laser
ii. Length stop
jj. Work support
a1. LED Worklight System

Electrical Safety

The electric motor has been designed for one voltage only. Always
check that the power supply corresponds to the voltage on the rating
plate.
Your tool is double insulated in accordance with EN 61029;
therefore no earth wire is required.
WARNING: 115 V units have to be operated via a fail-safe
isolating transformer with an earth screen between the
primary and secondary winding.
In case of cord replacement the tool must only be repaired by an
authorized service agent or by qualified electrician.

Mains Plug Replacement

(U.K. & Ireland only)
DANGER:
• Should your mains plug need replacing and you are competent to
do this, proceed as instructed below. If you are in doubt, contact
an authorized D WALT repair agent or a qualified electrician.
E
• Disconnect the plug from the supply.
• Cut off the plug and dispose of it safely; a plug with bared copper
conductors is dangerous if engaged in a live socket outlet.
• Only fit 13 Amperes BS1363A approved plugs fitted with the
correctly rated fuse (1).
• The cable wire colours, or a letter, will be marked at the connection
points of most good quality plugs. Attach the wires to their
respective points in the plug (see below). Brown is for Live (L) (2)
and Blue is for Neutral (N) (4).