Data Sheet - Genelec 8010A Operating Manual

Genelec Oy 8020
90
d
B
85
r
80
A
75
70
65
40 70 100 200 500
Figure 5: The upper curve group shows the horizontal directivity char-
acteristics of the 8020C measured at 1 m. The lower curve shows the
systems power response.
SyStem SpeCiFiCAtionS
Lower cut-off frequency, –3 dB
Upper cut-off frequency, –3 dB
Free field frequency response
Maximum short term sine wave acoustic output on axis in
half space, averaged from 100 Hz to 3 kHz
Maximum long term RMS acoustic output in same
conditions with IEC weighted noise (limited by driver unit
protection circuit
Maximum peak acoustic output per pair with music
material
Self generated noise level in half space at 1 m on axis
(A-weighted)
Harmonic distortion at 85 dB SPL at 1 m on axis
Freq: 50...100 Hz
> 100 Hz
Drivers
Bass
Treble
Weight
Dimensions
Height including Iso-Pod™ table stand
Height without Iso-Pod™ table stand
Width
Depth
Genelec Document BBA0088001a Copyright Genelec Oy 9.2013. All data subject to change without prior notice
(dBr) vs freq (Hz) 6 Apr 05
0° 15° 30°
45° 60°
5k 20k Hz
1k 2k 10k
8020C
< 65 Hz
> 21 kHz
66 Hz – 20 kHz (± 2.5 dB)
@ 1 m > 96 dB SPL
@ 1 m > 95 dB SPL
@ 1 m > 105 dB
< 10 dB
< 3 %
< 0.5 %
105 mm (4 in) cone
19 mm (3/4 in) metal dome
Both drivers are magnetically
shielded
3.7 kg (8.1 lb)
242 mm (9 / in)
1
2
230 mm (9 1 / in)
1
151 mm (6 in)
142 mm (5 / in)
5
8
International enquiries:
Genelec, Olvitie 5
FI 74100, Iisalmi
Finland
Phone +358 17 83881
Fax +358 17 812 267
Email genelec@genelec.com

Data Sheet

Genelec Oy 8020
90
d
B
85
r
80
A
75
BASS TILT
85
80
75
BASS ROLL-OFF
70
40 70 100 200 500
Figure 6: The curves above show the effect of the "bass tilt", "treble tilt"
and "bass roll-off" controls on the free field response.
AmpliFier SeCtion
Bass amplifier short term output power
Treble amplifier short term output power
Long term output power is limited by driver unit protection
circuitry
Amplifier system THD at nominal output
Mains voltage
Voltage operating range:
Power consumption (average)
Standby
Idle
Full output
CroSSover SeCtion
Signal input connector
XLR female, balanced 10 kOhm
Input level for 100 dB SPL output at 1 m
Sensitivity control range
Crossover frequency, Bass/Treble
Treble Tilt control operating range
Bass Tilt control operating range in 2 dB steps
Bass Roll-Off control
The 'CAL' position is with all tone controls set to 'off' and the input sensitivity control to maximum
(fully clockwise).
In the USA please contact
In China please contact:
Genelec, Inc., 7 Tech Circle
Beijing Genelec Audio Co. Ltd
Natick, MA 01760
Jianwai SOHO, Building 12, Room 2605
Phone +1 508 652 0900
D-1504, Chaoyang District
Fax +1 508 652 0909
Beijing 100022, China
Email genelec.usa@genelec.com
Phone +86 10 8580 2180
Fax +86 10 8580 2181
Email genelec.china@genelec.com
8020C
(dBr) vs freq (Hz) 6 Apr 05
TREBLE TILT
5k 20k Hz
1k 2k 10k
8020C
20 W at 8 Ohm load
20 W at 8 Ohm load
< 0.08 %
100, 120, 220 or 230 V
according to region
±10 %
<0.5 W
5 W
50 W
8020C
pin 1 gnd, pin 2 +, pin 3 -
-6 dBu at volume
control max
-80 dB relative to max output
3.0 kHz
0 to –2 dB @ 15 kHz
From 0 to -6 dB @ 100 Hz
–6 dB step @ 85 Hz
(to be used in conjunction with a
7050B subwoofer)
In Sweden please contact
Genelec Sverige
Ellipsvägen 10B
P.O. Box 5521, S-141 05 Huddinge
Phone +46 8 449 7070
Fax +46 8 708 7071
Email info@genelec.com
www.genelec.com