Troubleshooting - Shop-Vac SS11 User Manual

Hide thumbs Also See for SS11:

User manual (13 pages)

User manual (18 pages)

User manual (12 pages)

Table Of Contents

Table of Contents

Available languages

Enlarged version

dried before installing for dry pick up. With tank cover in

an upside down position, slide foam sleeve down over lid

cage pulling until foam sleeve completely covers lid cage

(figures 22, 23). Center the reusable dry filter on lid cage

(figure 24), slide mounting ring down over filter until ring is

positioned against the ribs of the lid cage (figure 25). The

reusable dry filter should always be in position over the foam sleeve for dry

pick up. To remove the filter for cleaning, remove mounting ring and filter from

lid cage (figure 26). To clean the reusable dry filter, shake off excess dirt and

dust or (depending on the condition of the filter) rinse with water. Allow the filter

to dry completely and reinstall. dO nOT MAChIne WASh OR dRy.

INSTALLING THE CARTRIDGE fILTER

(Not standard with all models)

NOTE: If foam sleeve is in postion over lid cage, it must be removed before installing cartridge

filter.

The cartridge filter can be used for wet or dry pick

up; installation is the same for both. When picking up

large quantities of liquid please refer to the Wet Pick up

Operation section in this manual. use the cartridge filter

in position over the lid cage for most general dry material

pick up. With the tank cover in an upside down position,

slide the cartridge filter down over the lid cage, pushing

until the filter seals against the cover (figure 27). Place

filter retainer into the top of the cartridge filter, hold the

tank cover with one hand, turn the handle on the filter

retainer clockwise to tighten, locking the filter into place

(figures 28 & 29). To remove the filter for cleaning, again

hold the tank cover and turn the filter retainer counter-

clockwise to loosen and remove, slide the cartridge filter

off the lid cage (figures 30 & 31). To clean the cartridge

filter shake or brush off excess dirt or rinse (from the inside of the filter) with water, dry com-

pletely (approximately 24 hours) and reinstall (figures 32 & 33). NOTE: If the filter has been

used for wet pick up, it must be cleaned and dried before using for dry pick up.

INSTALLING THE DISPOSABLE fILTER BAG

(Not standard with all models)

1. use for dry pick up only. use in conjunction with cartridge

filter for picking up soot, cement, plaster or drywall dust.

2. With cord disconnected from receptacle, pull latches in an

outward motion and remove tank cover.

3. Grasp cardboard collar firmly and slide rubber guard onto

inlet fitting as far as possible (figure 34).

4. When secured in place, expand bag and position around the inside of the tank (figure 35).

WARNING fOR fINE DUST & POWDERS

When vacuuming fine dust, or powders of any kind (ex. plaster, drywall dust, cold ashes, con-

crete dust, etc.)...a high efficiency drywall filter bag must be used. When vacuuming normal

household dust and debris, standard household disposable filter bags may be used. These

"large bag" filters connect to the air inlet fitting on the inside of the vacuum tank.

FILTER SELECTION GUIDE

Fine dust

SIZE

Drywall

Household

5-8 U.S. Gal (18.9-30.3L)

90671/

10-14 U.S. Gal (37.8-53L)

90672/

15-22 U.S. Gal (56.8-83.2L)

90673/

WET PICk UP OPERATION

Remove ALL dirt and debris found in the tank. The vacuum requires only a minimum of conver-

sion when going from dry to wet pick up. Remove all dry use filters from the vacuum. A clean

cartridge filter may be used for vacuuming small amounts of liquids. for proper installation of

the cartridge filter refer to Installing the Cartridge filter. for best results when vacuuming large

quantities of liquid, remove the cartridge filter. When vacuuming liquids containing debris, it is

recommended purchasing a foam sleeve and install over filter cage; otherwise a foam sleeve

is not required for wet pick up. foam sleeve and additional filters may be purchased by visiting

our website at www. shopvac.com, contacting our customer service department, or purchasing

at your local Shop-Vac

distributor.

Misting in exhaust air may occur if the filter becomes saturated during wet pick up. If misting

occurs, remove filter and allow to dry or, replace with another dry filter to eliminate the misting

and possible dripping of liquid around the lid. Turn the unit off immediately upon completing a

wet pick-up job or when tank is full and ready to be emptied. Raise the hose to drain any excess

liquid into the tank. The interior of the tank should be periodically cleaned.

The foam sleeve should be cleaned periodically as described in the following steps:

1. Always disconnect the plug from the wall receptacle before removing the tank cover. Place

tank cover in an upside down position. Remove foam sleeve by sliding it up and off the lid

cage.

2. Shake excess dust off foam sleeve with a rapid up and down movement.

3. hold foam sleeve under running water for a minute or two, rinsing from the inside. A water

wash is not always required, depending on the condition of the foam sleeve.

4. Gently wring out excess water, blot foam sleeve with a clean towel, and allow to dry. The

foam sleeve is now ready to be reinstalled on the lid cage.

90107/

REUSABLE DRY FILTER AND MOUNTING RING

Standard

fits most Shop-Vac

Wet/Dry Vacuums.

90661/

90585/

FOAM FILTER SLEEVE fits most Shop-Vac

90662/

Wet/Dry Vacuum

90663/

NOTE: WeT PICk uP ACCeSSORIeS ShOuLd Be WAShed PeRIOdICALLy, eSPeCIALLy AfTeR

PICkInG uP WeT, STICky kITChen ACCIdenTS. ThIS CAn Be ACCOMPLIShed WITh A WARM

SOLuTIOn Of SOAP And WATeR.

your vacuum can be used as a powerful blower. To use your unit as a blower,

clear hose of any obstruction. Insert machine hose end into blower port on

rear of unit (figure 36). Twist slightly to tighten the connection. Caution

should be used when using as a blower due to the powerful force of air when

using certain attachments.

WARNING

VENT ROCkS OR DEBRIS fROM BEING BLOWN OR RICOCHETING INTO

THE EyES OR fACE, WHICH CAN RESULT IN SERIOUS INjURy.

EMPTyING LIqUID WASTES fROM THE TANk

Not all units are equipped with tank drains. Follow the instructions, which apply to

your specific unit.

Without Tank Drain

Liquid waste may be emptied by removing the tank cover. To empty, stop the motor and

remove the plug from the wall receptacle. Remove the tank cover and deposit the liquid waste

contents in a suitable drain. After tank is empty, return the cover to its original position. To

continue use, plug the cord into the wall receptacle and turn the unit on.

With Tank Drain

Liquid waste may be emptied by removing the tank drain. To empty, turn unit off and remove

plug from wall receptacle. Remove the drain cap and deposit the liquid waste contents in a

suitable drain. After the tank is empty, return the drain cap to its original position. To continue

use, plug the cord into the wall receptacle and turn the unit on.

AUTOMATIC SUCTION SHUT-Off

The vacuum is equipped with an automatic suction shut-off that operates when picking up

liquids. As the level of the liquid rises in the tank, an internal float rises until it seats itself

against a seal at the intake of the motor, shutting off suction. When this happens, the motor will

develop a higher than normal pitch noise and the suction is drastically reduced. If this occurs,

turn unit off immediately. failure to turn unit off after float rises and shuts off suction will result

in extensive damage to the motor. To continue use, empty the liquid waste from the tank as

outlined in the previous paragraph.

NOTE: If ACCIdenTALLy TIPPed OVeR, The VACuuM COuLd LOSe SuCTIOn. If ThIS OCCuRS,

PLACe VAC In uPRIGhT POSITIOn And TuRn SWITCh Off. ThIS WILL ALLOW The fLOAT TO

ReTuRn TO ITS nORMAL POSITIOn, And yOu WILL Be ABLe TO COnTInue OPeRATIOn.

no lubrication is necessary as the motor is equipped with lifetime lubricated bearings.

Before storing your vacuum cleaner the tank should be emptied and cleaned.

The power cord can be wrapped around the cord wraps provided on the tank

cover on rear of unit (figure 37). Accessories may be stored in the tool holder

(not standard on all models) so they can be readily available. The vacuum

should be stored indoors.

Trouble

Suction weakens or

cleaner runs hot

Misting in the

exhaust air

WARNING

SHOULD BECOME DETACHED OR BROkEN, EXPOSING THE MOTOR OR ANy

OTHER ELECTRICAL COMPONENTS, OPERATION SHOULD BE DISCONTINUED

IMMEDIATELy TO AVOID PERSONAL INjURy OR fURTHER DAMAGE TO THE

VACUUM. REPAIRS SHOULD BE MADE BEfORE REUSING THE VACUUM.

THREE yEAR HOME USE WARRANTy

your Shop-Vac® vacuum cleaner is warranted for normal household use, in accordance with the

user Manual, against original defects in material and workmanship for a period of three years

from date of purchase. Should this product be used for commercial or rental use, a 90 day lim-

ited warranty will apply. Shop-Vac Corporation warrants placing this vacuum cleaner in correct

operating condition, by repair or parts replacement, during the warranty period, without charge.

This warranty does not cover accessories. use of non-recommended filters and/or accessories

may void the manufacturer's warranty. Shop-Vac® assumes no responsibility for damage or

faulty performance caused by misuse, careless handling, and where repairs or modifications

BLOWER fEATURE

– ALWAyS WEAR EyE PROTECTION TO PRE-

LUBRICATION

STORAGE