Dremel 8200 Original Instructions Manual page 22

wires by applying excessive load to the brush. The wire
bristles can easily penetrate light clothing and/or skin.
b. If the use of a guard is recommended for wire brushing,
do not allow any interference of the wire wheel or
brush with the guard. Wire wheel or brush may expand in
diameter due to work load and centrifugal forces.
c. Do not exceed 15000 min –1
Do not work with materials containing
WARNING
!
asbestos (asbestos is considered
carcinogenic).
Take protective measures when during
WARNING
!
work dust can develop that is harmful
to one's health, combustible or explosive (some dusts
are considered carcinogenic); wear a dust mask and
work with dust/ chip extraction when connectable.
ENVIRONMENT
DISPOSAL
The machine, accessories and packaging should be sorted for
environmental-friendly recycling.
ONLY FOR EUROPEAN COUNTRIES
Do not dispose of power tools into household waste!
According the European Guideline 2002/96/EC for
Waste Electrical and Electronic Equipment and its
implementation into national right, power tools that are
no longer usable must be collected separately and
disposed of in an environmentally correct manner.
SPECIFICATIONS
GENERAL SPECIFICATIONS
Voltage Rating . . . . . . . . . . . 10,8 V
Amperage Rating . . . . . . . . . 1,3 – 2,0 Ah
No Load Speed . . . . . . . . . . . n 5000 – 30000 min
o
Collet Capacity . . . . . . . . . . . 0,8 mm, 1,6 mm, 2,4 mm, 3,2 mm
SPECIFICATIONS CHARGER
Input . . . . . . . . . . . . . . . . . . . 230 V, 50 – 60 Hz, 26 W
Output . . . . . . . . . . . . . . . . . 3,6 V - 10,8 V , 1,5 A
EXTENSION CORDS
Use completely unrolled and safe extension cords with a
capacity of 5 Amps.
ASSEMBLY
ALWAYS TURN OFF THE TOOL BEFORE CHANGING ACCESSORIES,
CHANGING COLLETS, OR SERVICING THE TOOL.
when using wire brushes.
–1
22
BATTERY CHARGE CONDITION INDICATOR
LIGHTS
Your tool is equipped with charge condition indicator lights
(picture 1 D). The indicator lights shows the charge condition of
the battery.
3 of 3 Solid LED's = 67-100%
2 of 3 Solid LED's = 34-66%
1 of 3 Solid LED's = 16-33%
1 of 3 Flashing LED's = 0-15%
3 "side to side" lights – battery charge is too low to run tool.
Recharge the battery.
3 "flashing" lights – battery is too hot for use. Turn tool off and
let battery cool down.
Your tool is equipped with advanced electronics that protect
the Li-Ion cells in the battery from damage due to excessive
operating temperature and/or current draw. If the warning
symbol illuminates red and/or the tool stops working during
heavy use, this most likely indicates that the Li-Ion cells are
near their maximum operating temperature, and the battery
pack should either be changed or allowed to cool to ambient
temperature before continuing use. If the tool automatically turns
off due to overload conditions, the switch must be turned off for
a few seconds to allow the circuit to reset before continuing use.
IMPORTANT CHARGING NOTES
1. The charger was designed to fast charge the battery only
when the battery temperature is between 32°F (0°C) and
113°F (45°C). If the battery pack is too hot or too cold, the
charger will not fast charge the battery. (This may happen
if the battery pack is hot from heavy use). When the battery
temperature returns to between 32°F (0°C) and 113°F
(45°C), the charger will automatically begin charging.
2. A substantial drop in operating time per charge may mean
that the battery pack is nearing the end of its life and
should be replaced.
3. Remember to unplug charger during storage period.
NOTE: Use of chargers or battery packs not sold by Dremel will
void the warranty.
CHARGING BATTERY PACK (MODEL 875)
Plug charger cord into your standard power outlet.
With no battery pack inserted, the charger's green indicator light
will go ON. This indicates the charger is receiving power and the
charger is ready for operation.
When you insert the battery pack into the charger, the charger's
green indicator light will begin to "BLINK". This indicates that the
battery is receiving a fast charge.
PICTURE 9
A. Battery pack
B. Charger
C. Green light