Connecting To A Wireless Network; Tv Remote; Chapter 7 - Dlna (Share & See); Connecting To Your Pc - JVC LT-40HW62U User Manual

Chapter 7
• Enter the IP address, Subnet mask, Default
gateway, Primary DNS and Secondary DNS
values. Use the alphanumeric buttons to enter
numbers and the navigation buttons to move
from one entry field to another.
- Once Auto or Manual IP setting is completed,
press MENU to go back, press ▲/▼ to select
Connection test, then press OK/► to check the
Internet connectivity again.
5. If you want to see the information on current
connection, such as Interface, Address type,
IP address, etc., select Network > Network
settings > Information, then press OK/►.

Connecting to a wireless network

To establish a wireless connection between your
TV and your network, you need a wireless router or
modem and a Wireless LAN Adapter.
1. Press MENU on the remote control and select
Network > Network settings > Internet
connection. Press ◄/► to select On.
2. Press ▲/▼ to select Interface, then set ◄/► to
Wireless to select wireless-mode connection.
3. Press ▲/▼ to select Wireless setting and press
OK/► to enter.
4. You can set up the wireless network connection in
3 ways: a) or b) or c).
- a) Scan
• Press ▲/▼ to select Scan, then press OK/►.
The TV will search all access points within
range, access points found by the TV will be
displayed.
• Press ▲/▼ to select an available access point,
then press OK/► to connect the TV.
Notes:
- If you select a protected access point, you will
have to enter the corresponding password.
Press OK on the remote control to display the
virtual keyboard to enable you to enter the
password.
- This set is able to memorize the available
access point, which enables it to connect to
the network even if you switch on your TV
after power-off.
- b) Manual
Press ▲/▼ to select Manual, then press OK/►,
you will be prompted to enter the correct SSID
of an available wireless router to set up the
connection.
- c) Auto
If your AP (Access Point) supports WPS (Wi-
Fi Protected Setup), you can connect to the
network via PIN (Personal Identification Number)
or PBC (Push Button Configuration). WPS will
automatically configure the SSID and WPA key
in either mode.
Press ▲/▼ to select Auto, then press OK/► to
enter.
• PIN: Select PIN and press OK/► to enter.
Choose a random PIN code. Make sure
this code is installed on the AP. (For the
procedures, refer to your router manual.) Press
OK/► again to set up the connection.
• PBC: If your router has a PBC push button,
select PBC, then press OK/► to enter. Press
the PBC push button on your router within
2 minutes after you press OK/► again. Your
TV will automatically acquire all the network
setting values it needs and connect to your
network.
5. To check the Internet connectivity, follow the
instructions in steps 3 and 4 of the preceding
section Connecting to a wired network.
6. To see the information on current connection,
follow the instructions in step 5 of the preceding
section Connecting to a wired network.

TV remote

This function allows you to turn a smart device into a
sophisticated remote control, providing more features
than your normal TV remote control. You can then
control your TV through your smart device.
1. Select Network > TV Remote, then press OK to
enter the TV Remote menu. You will see details
for downloading the TV Remote application and
other related information.
The following instructions are based on the example
of a smartphone.
2. Download and install into the smartphone. the
correct TV Remote application for the smartphone.
3. Make sure the smartphone and the TV are in the
same home LAN (local area network) or network
segment.
4. Run the TV Remote application on the
smartphone, it will search and communicate with
the TV automatically to enable the TV Remote
functionality.
5. Once the TV and the smartphone are linked as
described in step 4, you will be able to enjoy the
extra features of the TV Remote function.
6. To quit the TV Remote function, press EXIT on the
remote control.
DLNA (Share & See)
Note: This manual covers products with either
Share & See or DLNA function. Share &
See is DLNA-compatible.

Connecting to your PC

Make sure to set up a wired or wireless connection
from your TV to a router first. Then connect your
PC to your router either through a network cable
EN 17
DLNA (Share & See)