Chapter 3 - Installing Channels; Initial Setup; Performing An Automatic Channel Search - JVC LT-40HW62U User Manual

Chapter 3

Initial setup

Initial setup involves selecting all the settings required
to be able to search for and store all the analogue
and digital channels you can receive.
Make sure that the television is switched on and
follow all the steps in turn specified hereafter.
Note: If the channel search retrieved only the
analogue channels it could be caused by poor
broadcasting and therefore is not covered
by manufacturer warranty. Manufacturers
cannot be held responsible for lack of or poor
broadcasting in some areas.
The first time you switch the set on, the Initial setup
wizard opens, which guides you through the initial
setup process.
Initial setup
Please select your language:
Български
1. Press ▲/▼ to select your language, then press
OK/► to enter the next step.
2. Press ▲/▼ to select your country, then press
OK/► to enter the next step.
3. Press ▲/▼ to select your location (Home or
Shop), then press OK/► to enter the next step.
4. Press ▲/▼ to select Network connection, then
press OK/► to enter the next step. (for more
information, see "Network connection" section
p.16)
Note: If you select France, you will have to enter the
Password setting menu here in order to set
a password. Use the alphanumeric buttons to
enter a four-digit number for your password.
(Your password cannot be 0000) Re-enter the
same code to confirm the password. After that,
you will enter the next step automatically. (In
this step, you can only press ◄ to return to the
previous step.)
5. Press ▲/▼ to select your tuner mode
or Cable.
- a) If you have selected
• Press OK/► to enter.
• Press ▲/▼ to select Digital & Analogue or
Digital or Analogue, then press OK/►.
• Press ▲/▼ to select Scan, then press OK/►
to start the automatic search for all DVB-T
digital and/or analogue channels.
Language
English
Hrvatska
Česky
Dansk
Select Next
Antenna
Antenna.
Note: not all contries have Favorite Network
Selection function.
- b) If you have selected
• Press OK/► to enter.
• Press ▲/▼ to select Digital & Analogue or
Digital or Analogue.
• If you select Digital & Analogue, press OK/►
to enter. Then:
- Press ▲/▼ to select Scan, then press OK/►.
- Press ◄/► to select the scan mode if
available (Full or Advanced).
- If you select Full, press OK to start the
automatic search for all DVB-C digital and/or
analogue channels.
- If you select Advanced, use the numeric
buttons to adjust the values for frequency,
symbol rate, network ID, and use ◄/► to
select the modulation mode; then press OK
to start the search for all DVB-C digital and/or
analogue channels.
• If you select Digital, press OK/► to enter,
then follow all the same steps as for Digital
& Analogue above, to search for all DVB-C
digital channels.
• If you select Analogue, press OK/► to enter,
press ▲/▼ to select Scan, then press OK/► to
start the search for all analogue channels.
Note: To prevent the channel setup process from
being interrupted, wait for the message
indicating that the setup is complete.
6. Before starting the scanning, you can also select
Skip scan to skip the initial setup process. In this
case, to search and store your channels you may
do an automatic channel search by following the
instructions in the next section Performing an
automatic channel search.
7. During the setup, you can follow the hints available
at the bottom of the screen to return to the
previous step by pressing ◄. You can also press
EXIT to exit or interrupt the search halfway.
- At anytime during the initial setup process, you
can press ◄ to return to the previous step.
- Once the initial setup process is complete,
you can press OK to exit the initial setup. The
channels are arranged in a preset order. If you
wish to skip channels, modify the preset order
or rename channels, select Setup > Organiser
and press OK/► to enter.

Performing an automatic channel search

This section describes how to search and store
channels automatically. Instructions are for both
analogue and digital channels. This may be done in
any of the cases below:
- you have selected Skip scan in the Initial setup
EN 8
Installing channels
Cable.