Specification - Panasonic WJ-HD309 Operating Instructions Manual

SPECIFICATION

General
Power source:
Power consumption
Ambient operating
temperature
Ambient operating
humidity
Dimensions
Weight
Input/Output
Video
Audio
Others
1
* When power is not supplied, video output signal was not sent from the unit even if video input signal is supplied.
2
* Non-voltage N.O. Contact, 100 mA, +5 V pull-up
3
* Open collector output, maximum under conditions of 24 V DC and 100 mA or less
4
* High (+12 V, 6.3 mA)
5
* 30 KΩ, 5 V pull-up, –100 mA, N.O. Contact
6
* 5 V pull-up, –100 mA, Non-voltage N.O. Contact input
7
* 200 mA at maximum
8
* Changeable with the mode switch
158
Video input connectors
Cascade input connector
Video output connectors
Monitor output connectors
Monitor output connector
(VGA)
S-video output connector
Video output connector
(front panel)
Audio input connectors
Audio output connectors
Expansion connector
Copy connectors
Control connectors
Alarm port
RS-485 ports
DATA ports
SERIAL connector
Ethernet port
120 V AC, 60 Hz
85 W
+5 °C to +45 °C
Less than 90 %
420 mm (W) X 88 mm (H) X 350 mm (D) [16-9/16" (W) X 3-7/16" (H) X
13-3/4" (D)] (excluding rubber feet and projections)
9.5 kg (21 lbs.)
1 V [P-P] / 75 Ω, with auto termination loop-thru, vertical timing pulse mul-
tiplexed, x8 (1 to 8 CH) (BNC)
1 V [P-P] / 75 Ω, with auto-termination loop-thru,
x8 (9 to 16 CH) (BNC)
1 V [P-P] / 75 Ω (BNC)
1 V [P-P] / 75 Ω, active loop-thru output, x8 (1 to 8 CH) (BNC)*
1 V [P-P] / 75 Ω, active loop-thru output, x8 (9 to 16 CH) (BNC)
1 V [P-P] / 75 Ω, x2 (BNC)
RGB output, x1 (15-pin D-sub)
Y = 1 V [P-P] / 75 Ω, C=0.286 V [P-P] / 75 Ω, x1 (S-video output connec-
tor)
1 V [P-P] / 75 Ω, x1 (RCA pin)
–10 dB, 10 KΩ, x4 (RCA pin)
–10 dB, 600 Ω, unbalanced, x2 (RCA pin)
High-speed serial interface, 480 Mbps (theoretical value), x1
High-speed serial interface, 480 Mbps (theoretical value), x2
Emergency recording input*
devices connected to copy connectors), HDD trouble output*
3
trouble output* , trouble output*
4
output* , time adjust input/output*
electricity failure detection input*
(25-pin D-sub) , +5 V output *
6
1 to 8 CH alarm input* , 1 to 16 CH alarm input*
2
alarm recovery input* , alarm suspension input*
RS-485 (full duplex/half duplex*
RS-485, x2 (RJ-11)
RS-232C, x1 (9-pin D-sub)
10 Base-T/100 Base-Tx (RJ-45)
2
, additional space warning output*
3
, electricity failure recovery completion
5
, sequence switching input/output*
2
, external recording mode switching*
7
2
, 1 to 16 alarm output*
5
(25-pin D-sub)
8
), x2 (RJ-11)
1
3
(for
3
, camera
5
,
2
3
,