JVC KD-S790 Service Manual page 37

QQ
3 7 63 1515 0
Pin
No Symbol I/O
17 TMAX O TMAX detection result output pin.
18 LPFN I Inverted input pin for PLL LPF amp.
19 LPFO O Output pin for PLL LPF amp.
20 PVREF - PLL-only VREF pin.
21 VCOF O VCO filter pin.
22 AV - Analog GND pin.
SS3
23 SLCO O DAC output pin for data slice level generation.
24 RFI I RF signal input pin. Zin selectable by command.
25 AV - Analog 3.3V power supply voltage pin.
DD3
26 RFCT I RFRP signal center level input pin.
27 RFZI I RFRP signal zero-cross input pin.
28 RFRP I RF ripple signal input pin.
29 FEI I Focus error signal input pin.
30 SBAD I Sub-beam adder signal input pin.
31 TEI I Tracking error input pin. Inputs when tracking servo is on.
32 TEZI I Tracking error signal zero-cross input pin.
33 FOO O Focus equalizer output pin.
34 TRO O Tracking equalizer output pin.
35 VREF - Analog reference power supply voltage pin.
36 RFGC O RF amplitude adjustment control signal output pin.
TE
L 13942296513
37 TEBC O Tracking balance control signal output pin.
38 SEL O APC circuit ON/OFF signal output pin. At laser on, high impedance with UHS="L",
H output with UHS="H".
39 AV - Analog 3.3V power supply voltage pin.
DD3
40 FMO O Feed equalizer output pin.
41 DMO O Disc equalizer output pin.
42 V - Digital GND pin.
SS3
43 V - Digital 3.3V power supply voltage pin.
DD3
44 TESIN I Test input pin. Normally, fixed to "L".
45 XV - System clock oscillator GND pin.
SS3
46 XI I System clock oscillator input pin.
47 XO O System clock oscillator output pin.
48 XV - System clock oscillator 3.3V power supply voltage pin.
DD3
49 DV R - DA converter GND pin.
SS3
50 RO O R-channel data forward output pin.
51 DV - DA converter 3.3V power supply pin.
DD3
52 DVR - Reference voltage pin.
53 LO O L-channel data forward output pin.
54 DV L - DA converter GND pin.
SS3
55 ZDET O 1 bit DA converter zero detection flag output pin.
56 V - Microcontroller interface GND pin.
SS5
57 BUS0
58 BUS1
www
59 BUS2 I/O Microcontroller interface data I/O pins.
60 BUS3
61 BUCK I Microcontroller interface clock input pin.
.
62 /CCE I Microcontroller interface chip enable signal input pin.At "L", BUS0 to BUS3 are active.
63 /RST I Reset signal input pin. At reset, "L".
64 V - Microcontroller interface 5V power supply pin.
DD5
http://www.xiaoyu163.com
TMAX Detection Result
Longer than fixed period
Within fixed period
Shorter than fixed period
x ao u163
y
i
http://www.xiaoyu163.com
2 9
8
Descroption
TMAX Output
"PV
"HiZ"
"AV
Q Q
3 6 7 1 3 1 5
co
.
9 4 2 8
"
DD3
"
SS3
0 5 8 2 9 9 4 2 8
m
(No.49788)1-37
KD-S790
9 9
9 9