Page 1
KD-S790 3 7 63 1515 0 SERVICE MANUAL CD RECEIVER 49788 2003 KD-S790 L 13942296513 Area Suffix J ----------- Northern America COMPACT DIGITAL AUDIO TABLE OF CONTENTS Important Safety Precautions ............1-2 Disassembly method .
KD-S790 SECTION 1 3 7 63 1515 0 Important Safety Precautions 1.1 Safety Precautions Burrs formed during molding may be left over on some parts of the chassis. Therefore, pay attention to such burrs in the case of preforming repair of this system.
Page 3
KD-S790 1.2 Preventing static electricity 3 7 63 1515 0 Electrostatic discharge (ESD), which occurs when static electricity stored in the body, fabric, etc. is discharged, can destroy the laser diode in the traverse unit (optical pickup). Take care to prevent this when performing repairs.
KD-S790 SECTION 2 3 7 63 1515 0 Disassembly method 2.1 Main body 2.1.1 Removing the front panel assembly Front panel assembly (See Fig.1) (1) Push the detach button in the lower left part of the front panel assembly and remove the front panel assembly in the direction of the arrow.
KD-S790 2.1.3 Removing the heat sink 3 7 63 1515 0 (See Fig.5) (1) Remove the two screws C and two screws D on the left side of the main body. Heat sink Fig.5 2.1.4 Removing the bottom cover (See Figs.6 and 7)
KD-S790 2.1.6 Removing the main board 3 7 63 1515 0 Main board (See Fig.9) • Prior to performing the following procedure, remove the front panel assembly, front chassis assembly, heat sink, bottom cover and rear bracket. (1) Remove the two screws H attaching the main board.
Page 7
KD-S790 2.1.8 Removing the front board 3 7 63 1515 0 (See Figs.11 to 13) • Prior to performing the following procedure, remove the front panel assembly. (1) Remove the four screws K on the back side of the front panel assembly.
Page 8
KD-S790 2.2 CD Mechanism Assembly 3 7 63 1515 0 2.2.1 Removing the top cover (See Figs.1 and 2) (1) Remove the two screws A on the both side of the body. (2) Lift the front side of the top cover and move the top cover backward to release the two joints a.
Page 9
KD-S790 2.2.2 Removing the connector board 3 7 63 1515 0 Wires (See Figs.3 to 5) CAUTION: Before disconnecting the flexible wire from the pickup, solder the short-circuit point on the pickup. No observance of this in- struction may cause damage of the pickup.
Page 10
KD-S790 2.2.3 Removing the DET switch 3 7 63 1515 0 (See Figs.6 and 7) (1) Extend the two tabs c of the feed sw. holder and pull out the switch. (2) Unsolder the DET switch wire if necessary.
Page 11
KD-S790 2.2.4 Removing the chassis unit 3 7 63 1515 0 (See Figs.8 and 9) • Prior to performing the following procedure, remove the top Chassis unit cover and connector board. Suspension spring (L) Suspension spring (R) (1) Remove the two suspension springs (L) and (R) attaching the chassis unit to the frame.
Page 12
KD-S790 2.2.5 Removing the clamper assembly 3 7 63 1515 0 (See Figs.10 and 11) • Prior to performing the following procedure, remove the top cover. (1) Remove the clamper arm spring. Clamper arm spring (2) Move the clamper assembly in the direction of the arrow to release the two joints d.
Page 13
KD-S790 2.2.6 Removing the loading / feed motor assembly 3 7 63 1515 0 (See Figs.12 and 13) • Prior to performing the following procedure, remove the top cover, connector board and chassis unit. (1) Remove the screw C and move the loading / feed motor assembly in the direction of the arrow to remove it from the chassis rivet assembly.
Page 14
KD-S790 2.2.7 Removing the pickup unit 3 7 63 1515 0 Pickup unit (See Figs.14 to 18) • Prior to performing the following procedure, remove the top cover, connector board and chassis unit. (1) Remove the screw D and pull out the pu. shaft holder from the pu.
Page 15
KD-S790 2.2.9 Removing the trigger arm 3 7 63 1515 0 Joint k (See Figs.19 and 20) • Prior to performing the following procedure, remove the top cover, connector board and clamper unit. (1) Turn the trigger arm in the direction of the arrow to release Trigger arm the joint k and pull out upward.
Page 16
KD-S790 2.2.11 Removing the mode sw. / select lock arm 3 7 63 1515 0 Link plate Joint t (See Figs.22 and 23) Mode sw. • Prior to performing the following procedure, remove the top plate assembly. Select lock arm (1) Bring up the mode sw.
Page 17
KD-S790 2.2.12 Reassembling the mode sw. / select lock arm 3 7 63 1515 0 Select lock arm spring (See Figs.24 to 26) REFERENCE: Hook w Reverse the above removing procedure. Joint v (1) Reattach the select lock arm spring to the top plate and set...
Page 18
KD-S790 2.2.13 Removing the select arm R / link plate 3 7 63 1515 0 Joint c' Link plate Joint r (See Figs.27 and 28) Select arm R Joint b' • Prior to performing the following procedure, remove the top plate assembly.
Page 19
KD-S790 2.2.15 Removing the loading roller assembly 3 7 63 1515 0 (See Figs.31 to 33) Loading roller assembly • Prior to performing the following procedure, remove the Roller guide clamper assembly and top plate assembly. spring (1) Push inward the loading roller assembly on the gear side and detach it upward from the slot of the joint g' of the lock arm rivet assembly.
Page 20
KD-S790 2.2.16 Removing the loading gear 5, 6 and 7 3 7 63 1515 0 Loading gear bracket (See Figs.35 and 36) • Prior to performing the following procedure, remove the top Loading gear 6 cover, chassis unit, pickup unit and top plate assembly.
KD-S790 2.2.17 Removing the gears 3 7 63 1515 0 Joint p' (See Figs.37 to 40) • Prior to performing the following procedure, remove the top Change plate cover, chassis unit, top plate assembly and pickup unit. rivet assembly •...
KD-S790 2.2.18 Removing the turn table / spindle motor 3 7 63 1515 0 Turn table (See Figs.41 and 42) • Prior to performing the following procedure, remove the top cover, connector board, chassis unit and clamper assembly. (1) Remove the two screws L attaching the spindle motor as- sembly through the slot of the turn table on top of the body.
6. Digital tester FM 87.5MHz ~ 107.9MHz 7. Tracking offset meter AM 530kHz ~ 1710 kHz 8. Test Disc JVC :CTS-1000 9. Extension cable for check EXTSH002-22P 1 Dummy load Exclusive dummy load should be used for AM and FM. For FM dummy load,there is a loss of 6dB between SSG output and antenna input.The loss of 6dB need not be considered...
Page 24
KD-S790 3.2 Troubleshooting 3 7 63 1515 0 3.2.1 Feed section Is the voltage output at Is the wiring for IC521 Is 5V present at IC581 Check CD 9V IC521 pin u 5V or 0V? (90) ~ (100) correct? pin 6? and 5V.
Page 25
KD-S790 3.2.5 Signal processing section 3 7 63 1515 0 Compare the L-ch and R-ch No sound from either Is the sound output from channel. to locate the defective point. both channels (L, R)? Check the vicinity of the...
Page 26
KD-S790 3.3 Maintenance of laser pickup 3 7 63 1515 0 3.4 Replacement of laser pickup (1) Cleaning the pick up lens Before you replace the pick up, please try to clean the lens Turn off the power switch and,disconnect the power cord with a alcohol soaked cotton swab.
Page 28
KD-S790 4.2 LA47505 (IC351) : Power amp. 3 7 63 1515 0 • Terminal layout Protective circuit Stand by Switch L 13942296513 Ripple Mute Filter circuit protective circuit Muting & On Time Control Circuit u163 1-28 (No.49788) http://www.xiaoyu163.com...
Page 29
KD-S790 • Terminal layout 3 7 63 1515 0 • Pin function Pin No. Symbol Function AC CONT1 Header of IC GND1 Power GND OUTFR- Outpur(-) for front Rch STBY Stand by input OUTFR+ Output (+) for front Rch...
Page 31
KD-S790 • Pin function 3 7 63 1515 0 Pin No. Symbol Function VIN1-A CH1 input AMP_inverted input VIN1+A CH1 input AMP_non-inverted input VCCP1 CH1 and CH2 power stage power supply VO1+ Output pin(+)for channel 1 VO1- CH1 output pin (-) for channel 1...
Page 32
KD-S790 4.4 NJM4565M-WE (IC571) : CD L.P.F. 3 7 63 1515 0 A OUTPUT A INPUT B OUTPUT A INPUT B INPUT B INPUT L 13942296513 u163 1-32 (No.49788) http://www.xiaoyu163.com...
Page 37
KD-S790 3 7 63 1515 0 No Symbol I/O Descroption TMAX O TMAX detection result output pin. TMAX Detection Result TMAX Output Longer than fixed period "PV " Within fixed period "HiZ" Shorter than fixed period "AV " LPFN I Inverted input pin for PLL LPF amp.
Page 40
KD-S790 4.10 UPD178078GF-594 (IC701) : System CPU 3 7 63 1515 0 • Pin layout • Pin function Pin No. Symbol Function No use VOL-DA I/O VOL IC communication line VOL-CLK VOL IC communication line No use LCD-DA LCD driver communication line...
Page 41
KD-S790 3 7 63 1515 0 Pin No. Symbol Function FM E.OUT PLL error output for FM IC(VPP) Setting to write for flash RESET System reset CD mechanism switch REMOCON Remocon input 53,54 No use POWER Power control CD-ON...
Page 42
KD-S790 3 7 63 1515 0 L 13942296513 u163 VICTOR COMPANY OF JAPAN, LIMITED AV & MULTIMEDIA COMPANY 10-1,1chome,Ohwatari-machi,Maebashi-city,371-8543,Japan (No.49788) Printed in Japan 0202WPC http://www.xiaoyu163.com...
Page 43
KD-S790 3 7 63 1515 0 SCHEMATIC DIAGRAMS CD RECEIVER KD-S790 CD-ROM No.SML200302 L 13942296513 Area suffix J ------------ Northern America Contents Block diagram Standard schematic diagrams Printed circuit boards 2-5~7 u163 No.49788SCH COPYRIGHT 2003 VICTOR COMPANY OF JAPAN, LTD.
KD-S790 3 7 63 1515 0 Safety precaution Burrs formed during molding may be left over on some parts of the chassis. Therefore, pay attention to such burrs in the case of preforming repair of this system. Please use enough caution not to see the beam directly or touch it in case of an adjustment or operation check.
Page 55
KD-S790 3 7 63 1515 0 < M E M O > L 13942296513 u163 2-11 http://www.xiaoyu163.com...
Page 56
KD-S790 3 7 63 1515 0 L 13942296513 u163 VICTOR COMPANY OF JAPAN, LIMITED AV & MULTIMEDIA COMPANY 10-1,1Chome,Ohwatari-machi,Maebashi-city,371-8543,Japan Printed in Japan (No.49788SCH) 2003/02 http://www.xiaoyu163.com...
KD-S790 3 7 63 1515 0 PARTS LIST [ KD-S790 ] * All printed circuit boards and its assemblies are not available as service parts. Area suffix J -------------- Northern America L 13942296513 - Contents - 3- 2 Exploded view of general assembly and parts list (Block No.M1) 3- 5 CD mechanism assembly and parts list (Block No.MB)
Page 58
KD-S790 3 7 63 1515 0 Exploded view of general assembly and parts list Block No. L 13942296513 u163 http://www.xiaoyu163.com...
Page 59
KD-S790 3 7 63 1515 0 Parts list (General assembly) Block No. M1MM Item Description Parts number Parts name Q'ty Area CD MECHA -------------------- GE10043-210A TOP CHASSIS GE40135-001A EARTH PLATE GE30568-006A HEAT SINK GE30393-002A BOTTOM COVER FSMA3005-001 INSULATOR QYSDST2604Z...
Page 60
KD-S790 3 7 63 1515 0 Parts list (General assembly) Block No. M1MM Item Description Parts number Parts name Q'ty Area VKW3001-330 COMP.SPRING 1 FOR DETACH BUTT GE10060-001A REAR COVER VKZ4777-001 MINI SCREW 4 FRONT+REAR GE30821-001A LCD CASE GE30805-001A...
Page 61
KD-S790 3 7 63 1515 0 CD mechanism assembly and parts list Block No. Grease TNG-87 TN-2001-1011 GP-501MK CFD-005Z GP-501A L 13942296513 u163 http://www.xiaoyu163.com...
KD-S790 3 7 63 1515 0 Parts list (CD mechanism) Block No. MBMM Item Description Parts number Parts name Q'ty Area FRAME 30320101T 30320102T TOP COVER 30320115T DANPER F 30320116T DANPER R 303205505T CHASSIS RIVET 303205503T CHANGE P. RVT A...
KD-S790 3 7 63 1515 0 Parts list (CD mechanism) Block No. MBMM Item Description Parts number Parts name Q'ty Area 30321103T LOADING GEAR 3 30321104T LOADING GEAR 4 30321105T LOADING GEAR 5 30321106T LOADING GEAR 6 LOADING GEAR 7...
Page 64
KD-S790 3 7 63 1515 0 Electrical parts list (Main board) Block No. 01 Item Parts number Parts name Remarks Area Item Parts number Parts name Remarks Area NCB31EK-473X C CAPACITOR C 510 NCB31CK-104X C CAPACITOR QEKJ1HM-104Z E CAPACITOR .10MF 20% 50V...
Page 65
KD-S790 3 7 63 1515 0 Electrical parts list (Main board) Block No. 01 Item Parts number Parts name Remarks Area Item Parts number Parts name Remarks Area C 707 QEKJ0JM-227Z E CAPACITOR 220MF 20% 6.3V D 713 LNJ308G81/1-3/X...
Page 66
KD-S790 3 7 63 1515 0 Electrical parts list (Main board) Block No. 01 Item Parts number Parts name Remarks Area Item Parts number Parts name Remarks Area R 476 NRSA02J-101X MG RESISTOR R 705 NRSA63J-271X MG RESISTOR R 503...
Page 67
KD-S790 3 7 63 1515 0 Block No. 01 Electrical parts list (Main board) Item Parts number Parts name Remarks Area S 703 QSQ1A11-V06Z TACT SWITCH RESET TU 1 QAU0281-001 TUNER PACK X 521 QAX0741-001Z C RESONATOR X 701...
Page 68
KD-S790 3 7 63 1515 0 Electrical parts list (Front board) Block No. 02 Item Parts number Parts name Remarks Area Item Parts number Parts name Remarks Area C 601 NCB31HK-223X C CAPACITOR R 647 NRSA02J-122X MG RESISTOR C 602...
Page 69
KD-S790 3 7 63 1515 0 < M E M O > L 13942296513 u163 3-13 http://www.xiaoyu163.com...
Page 70
KD-S790 3 7 63 1515 0 Packing materials and accessories parts list Block No. Block No. A1~A7 L 13942296513 KIT:A8~A12 u163 3-14 http://www.xiaoyu163.com...
Page 71
KD-S790 3 7 63 1515 0 Parts list (Packing) Block No. M3MM Item Q'ty Description Parts number Parts name Area FSPG4002-001 POLY BAG 1 FOR INST. BOOK QPA00801205 POLY BAG FSYH4036-068 SHEET 1 MIRAMA SHEET QPA01003003 POLY BAG QPC03004315P...