Denon AVR-1712 Owner's Manual page 67

Audio Setup
Make settings for audio playback.
Setting items
2ch Direct/Stereo Setting : Select the method for setting the speakers used in the 2-channel
Select the method for direct and stereo playback modes.
setting the speakers used • Basic : The settings at "Speaker Setup" (vpage 60) are applied.
in the 2-channel direct and • Custom : Make separate settings for 2-channel. Make the following
stereo playback modes. settings:
Front : Set the front speaker size.
• Large : Use a large speaker that can adequately play back low
frequencies.
• Small : Use a small speaker that has inadequate playback capacity for
low frequencies.
If "Speaker Config." – "Subwoofer"
the setting is automatically set to "Large".
Subwoofer : Set the presence of a subwoofer.
• Yes : Use a subwoofer.
• No : Select when a subwoofer is not connected.
If "Speaker Config." – "Subwoofer"
the setting is automatically set to "No". If the "Front" setting is
"Small", the setting is automatically "Yes".
Subwoofer Mode : Select low range signals to be reproduced by
subwoofer.
• LFE : When the "2ch Direct/Stereo" – "Front" setting is set to "Large",
the LFE signal alone is output from the subwoofer. Also, when the "2ch
Direct/Stereo" – "Front" setting is set to "Small", the front channel low
range signal is added to the LFE signal output from the subwoofer.
• LFE+Main : The front channel low range signal is added to the LFE signal
output from the subwoofer.
This setting can be set made "2ch Direct/Stereo" – "SW" is set to
"Yes".
Crossover : Set the maximum frequency of the bass signal output from
each channel to the subwoofer.
• 40Hz / 60Hz / 80Hz / 90Hz / 100Hz / 110Hz / 120Hz / 150Hz / 200Hz /
250Hz
• This setting can be set made "2ch Direct/Stereo" – "SW" is set to
"Yes".
• If the "2ch Direct/Stereo" – "Front" setting is "Large" and the "SW
Mode" setting is "LFE", "Full Band" is displayed and the setting cannot
be made.
BD
Default settings are underlined.
Setting details
(vpage 60) is set to "No",
(vpage 60) is set to "No",
Setting items
2ch Direct/Stereo Distance FL / Distance FR : Select the speaker.
(Continued) • 0.0ft – 60.0ft (12.0ft) / 0.00m – 18.00m (3.60m) : Set the distance to
the speaker.
Set the difference in the distance between the speakers to less than
20.0 ft (6.00 m).
Level FL / Level FR : Select the speaker.
• –12.0dB – +12.0dB (0.0dB) : Adjust the level of each channel.
Auto Surround ON : Memorize settings. Automatically play with the last used surround
Make setting for mode.
memorizing surround mode OFF : Do not memorize settings. Surround mode does not change
setting for each input signal according to input signal.
type.
• The auto surround mode function lets you store in the memory the
surround mode last used for playing the four types of input signals listed
below.
q Analog and PCM 2-channel signals
w Dolby Digital and DTS 2-channel signals
e Dolby Digital and DTS multi-channel signals
r LPCM Multi-channel signals
• When playing in PURE DIRECT, the surround mode does not change
even if the input signal is changed.
EQ Customize Manual : Set when not using the "Manual" equalizer.
Set the disengaged • Used : Use.
equalizers to not display • Not Used : Do not use.
when the "MultEQ ® XT" is
Audyssey Flat : Set when not using "Audyssey Flat" equalizer.
selected.
• Used : Use.
• Not Used : Do not use.
Set so that "Audyssey Flat" settings can be made when Audyssey ®
The equalizer mode in which
Auto Setup is performed.
"Not Used" is selected
Audyssey Byp. L/R : Set when not using "Audyssey Byp. L/R" equalizer.
cannot be stored and
• Used : Use.
recalled in the Quick Select
• Not Used : Do not use.
function.
Set so that "Audyssey Byp. L/R" settings can be made when
Audyssey ® Auto Setup is performed.
64
System Setup
Setting details