Audio Settings - Kenwood KDC-BT600U Instruction Manual

AUDIO SETTINGS

While listening to any source...
1
Press the volume knob to enter [FUNCTION].
2
Turn the volume knob to select [AUDIO CONTROL], then press the
knob.
3
Turn the volume knob to select an item (see the following table),
then press the knob.
4 Repeat step 3 until the desired item is selected or activated.
5 Press and hold to exit.
(or using RC-406)
1
Press AUD to enter [AUDIO CONTROL].
2
Press to select an item, then press
To return to the previous setting item, press
SUB-W LEVEL –50 to +10 (0): Adjusts the subwoofer output level.
MANUAL EQ
BAND1 LEVEL LEVEL
BASS EXTEND
BAND2 LEVEL to –9 to +9 (0): The sound elements (frequency level, tone level, Q factor)
BAND13 LEVEL are preset into each selection (BAND1 LEVEL to BAND13 LEVEL).
Adjusts the level to memorize for each source. (Before making an
adjustment, select the source you want to adjust.)
Q FACTOR 1.35/ 1.50/ 2.00: Adjust the quality factor.
PRESET EQ NATURAL/ ROCK/ POPS/ EASY/ TOP40/ JAZZ/ POWERFUL/ USER:
Selects a preset equalizer suitable to the music genre. (Select [USER] to
use the settings made in [MANUAL EQ].)
BASS BOOST LEVEL1/ LEVEL2/ LEVEL3/ LEVEL4/ LEVEL5 or LV1/ LV2/ LV3/ LV4/
LV5: Selects your preferred bass boost level. ; OFF: Cancels.
18
.
.
Default: XX
–9 to +9 (0): (Refer to BAND2 LEVEL below.)
ON: Turns on the extended bass. ; OFF: Cancels.
LOUDNESS LEVEL1/ LEVEL2 or LV1/ LV2: Selects your preferred low and high
frequencies boost to produce a well-balanced sound at a low volume
level. ; OFF: Cancels.
SUBWOOFER SET ON: Turns on the subwoofer output. ; OFF: Cancels.
FADER (Not applicable if 3-way crossover is selected.)
R15 to F15 (0): Adjusts the rear and front speaker output balance.
BALANCE L15 to R15 (0): Adjusts the left and right speaker output balance.
VOLUME OFFSET –15 to +6 (0): Preset the initial volume level of each source. (Before
adjustment, select the source you want to adjust.)
SOUND EFFECT
SOUND RECNSTR (Not applicable for TUNER source and AUX source.)
(Sound ON: Creates realistic sound by compensating the high-frequency
reconstruction) components and restoring the rise-time of the waveform that are lost
in audio data compression. ; OFF: Cancels.
SPACE ENHANCE (Not applicable for TUNER source.)
SMALL/ MEDIUM/ LARGE or SML/ MED/ LRG: Virtually enhances
the sound space. ; OFF: Cancels.
SND REALIZER LEVEL1/ LEVEL2/ LEVEL3 or LV1/ LV2/ LV3: Virtually makes the
sound more realistic. ; OFF: Cancels.
STAGE EQ LOW/ MIDDLE/ HIGH or LOW/ MID/ HI: Virtually adjust the sound
position heard from the speakers. ; OFF: Cancels.
DRIVE EQ ON: Boosts the frequency to reduce the noise heard from outside the
car or running noise of the tyres. ; OFF: Cancels.
Depending on the crossover type you have selected ( 5), 2-way
SPEAKER SIZE
crossover or 3-way crossover setting items will be shown. ( 19, 20)
X ' OVER
By default, 2-way crossover type is selected.
• : For 2-way crossover: [SUB-W LEVEL]/ [SUBWOOFER SET] is
selectable only if [SWITCH PREOUT] is set to [SUB-W]. ( 5)
• [SUB-W LEVEL] is selectable only if [SUBWOOFER SET] is set to [ON].