Haier L24C1180 Service Manual

23.6" lcd tv
Hide thumbs Also See for L24C1180:

Advertisement

23.6 LCD TV
Service
Service
Service
Description
Table of Contents............................................................1
Important Safety Notice...................................................2
Revision List.........................................................3
1. General Specification..................................................4
2. Operating Instructions............................................6
2.1 The Use of Remote Control...................................6
2.2 To Use the Menus...............................................7
2.3 Front Panel Control Knobs..................................13
2.4 How to Connect................................................14
3. Input/Output Specification.......................................15
4. Mechanical Instructions.........................................17
5. Repair Flow Chart .............................................20
6. PCB Layout ......................................................27
6.1 Main Board.......................................................27
ANY PERSON ATTEMPTING TO SERVICE THIS CHASSIS MUST FAMILIARIZE HIMSELF WITH THE CHASSIS
AND BE AWARE OF THE NECESSARY SAFETY PRECAUTIONS TO BE USED WHEN SERVICING
ELECTRONIC EQUIPMENT CONTAINING HIGH VOLTAGES.
CAUTION: USE A SEPARATE ISOLATION TRANSFOMER FOR THIS UNIT WHEN SERVICING

TABLE OF CONTENTS

Page
Description
6.2 Power Board..................................................29
6.3 Key Board.....................................................32
6.4 IR Board.......................................................32
7. Adjustment.....................................................33
7.1 ADC Adjustment............................................33
7.2 FW Upgrade.................................................34
7.3 The Writing VGA & HDMI EDID.........................38
8. Block Diagram........................................................43
9. Wiring Diagram......................................................44
10. Schematic Diagram........................................45
10.1 Main Board..................................................45
10.2 Power Board.................................................55
10.3 Key Board...................................................57
10.4 IR Board.....................................................58
SAFETY NOTICE
1
Haier L24C1180
Horizontal Frequency
31.5~68 KHz
Page

Advertisement

Table of Contents
loading

Summary of Contents for Haier L24C1180

  • Page 1: Table Of Contents

    23.6 LCD TV Haier L24C1180 Service Service Service Horizontal Frequency 31.5~68 KHz TABLE OF CONTENTS Description Page Description Page 6.2 Power Board…..…………..………….…..……..29 Table of Contents..……........…..1 6.3 Key Board………………………..……..………..32 Important Safety Notice........……..2 6.4 IR Board…………………………..……….……..32 Revision List…………………………………………………3 7. Adjustment……………….……….…………...………33 1. General Specification.........………..4 7.1 ADC Adjustment……………………..……...………33...
  • Page 2: Important Safety Notice

    Important Safety Notice Proper service and repair is important to the safe, reliable operation of all Haier Company Equipment. The service procedures recommended by Haier and described in this service manual are effective methods of performing service operations. Some of these service operations require the use of tools specially designed for the purpose.
  • Page 3: Revision List

    Revision List Revision Version Release Date Customer Model Model Instructions Jan.12,2011 Initial release L24C1180 E2CBMZNK3WH3NN...
  • Page 4: General Specification

    PC IN: D-SUB and PC Audio (Headphone mini-jack) Supported scan rate: 640x480@60/72/75Hz,720x400@70Hz, 800x600@56/60/72/75Hz,1024x768@60/70/75Hz, 1280x720@60Hz,1280x768@60Hz Note: 1360x768@60Hz: For L19C1120/L22C1120 only. 1280x1024@60Hz,1440x900@60Hz,1680x1050@60Hz 1920x1080@60Hz: For L24C1180 only. For L19C1120/L22C1120: 1360x768@60Hz. Rear Connectors For L24C1180: 1920x1080@60Hz. Component Video and L/R Audio input Supported resolution: 480i@59.94/60Hz, 480p@59.94/60Hz, 720p@59.94/60Hz, 1080i@59.94/60Hz, 1080p@59.94/60Hz.
  • Page 5 Model No. L24C1180 POWER Power Consumption Standby <1W Mains Power 120V~60Hz Audio Power 3W+3W Ambient Temperature 5°C - 35°C PACKAGE CONTENTS TV unit x1 Base x1 Power cord x 1 Supplied Accessories Remote control x1 (with two size AAA alkaline batteries)
  • Page 6: Operating Instructions

    2. Operating Instructions 2.1 The Use of Remote Control Power Source Press to power ON/OFF(standby) TV. Press "Source" to open the Source List. (Note: TV is never completely power off unless physically unplugged. Press to display the Electronic Program Video Guide.
  • Page 7: To Use The Menus

    2.2 To Use the Menus 1. Press the Menu button to display or close the main menu. 2. Use the Navigation Ring to move around, select, adjust or confirm an item in the OSD (On Screen Display) menu. Press the Menu button to enter the main OSD. Adjust the items including Video menu, Audio menu, Feature menu, Channel menu, and VGA menu.
  • Page 8 or Personal. 2. Brightness: Video brightness adjustment, the tuning range is 0 ~ 100. 3. Contrast: Video contrast adjustment, the tuning range is 0 ~ 100. 4. Sharpness: Video sharpness adjustment, the tuning range is 0 ~ 100. 5. Color: Video color chroma adjustment, the tuning range is 0 ~ 100. 6.
  • Page 9 FEATURE MENU The Feature menu in TV mode is shown below. Certain features will be hidden (disabled) in the menu depending on the mode. 1. Menu Language: Select the menu display language. (English / Français / Español) 2. Time: Set current time. The sub-menu includes Time Mode, Time Zone, and Daylight Savings. [Time Mode] –...
  • Page 10 sub-menu, enter the password first. Then the user can modify the MPAA or TV Rating table to restrict viewing of certain programs. Note: This feature is only available in TV, Composite and S-Video source modes. (The default password is: 0 0 0 0.) [Button Lock] –...
  • Page 11 There are two ways to enter JPEG Viewer and MP3 MusicBox interface: • After a plugging USB storage device into the USB port, the Multimedia List menu will be displayed. • Select MultiMedia Menu in the Feature Menu to choose JPEG Viewer or MP3 MusicBox. These two items are activated only if the USB storage device is plugged into the USB port.
  • Page 12 1. H-Position: Adjust the horizontal position of the picture. (0-40) 2. V-Position: Adjust the vertical position of the picture. (0-16) 3. Clock: Adjust picture clock to reduce Vertical-Line noise. (0-16) 4. Phase: Adjust picture phase to reduce Horizontal-Line noise. (0-31) 5.
  • Page 13: Front Panel Control Knobs

    2.3 Front Panel Control Knobs 1. VOL + Press to increase the sound volume level. 2. VOL - Press to decrease the sound volume level. 3. CH Press to select the next higher program number. 4. CH Press to select the next lower program number. 5.
  • Page 14: How To Connect

    2.4 How to Connect 1. HDMI – Connect the primary source for digital video such as a DVD player, bluray player or set top box through this digital connector. 2. PC IN – Connect the video and audio cables from a computer here. 3.
  • Page 15: Input/Output Specification

    3. Input/Output Specification 3.1 Input Signal Connector D-SUB Pin No. Description Pin No. Description Red Video No Pin Green Video Sync Ground Blue Video SDA(Remote Control) SCL(Remote Control) Serial Data for DDC Ground H. Sync Red Ground V. Sync Green Ground Serial Clock for DDC Blue Ground HDMI...
  • Page 16 3.2 Input Signal Timing Analog RGB Input VESA MODES Horizontal Vertical Nominal Nominal Nominal Sync Sync Pixel Mode Resolution Total Frequency Freq. Polarity Polarity Clock (KHz) (Hz) (MHz) 640x480@60Hz 800 x 525 31.469 59.940 25.175 640x480@72Hz 832 x 520 37.861 72.809 31.500 640x480@75Hz...
  • Page 17: Mechanical Instructions

    4. Mechanical Instructions Step1. Remove the STAND ASS’Y. Step2. Remove the REAR COVER.
  • Page 18 Step 3. Disconnect the WIRE HARNESS. Step 4. Remove the MAIN BOARD and POWER BOARD and separate the PANEL and BEZEL.
  • Page 19 Step 5. Separate the MAIN FRAME and PANEL. Step 6. Remove the KEY BOARD, IR BOARD and SPEAKERS.
  • Page 20: Repair Flow Chart

    5. Repair Flow Chart 1. No power No power (LED “Off”) Check the AC input and Power “On” the power is “ON”? Power board output=5V? Replace the power board Check the IR board and LED Replace the IR board Replace the main board...
  • Page 21 2. Can’t start Can’t start LED red Replace the power board Power board output 16V? Replace the key board Check the power key is under control? Replace the IR board Check the IR receiver is normal? Replace the main board Replace the Power board...
  • Page 22 3. Abnormal Display Abnormal Display Reset the source Check the source Enter factory mode to do “EEPROM initial”&“Reset” Replace the main board Check the main board Replace the LVDS cable Check the LVDS cable Check the panel Replace the panel...
  • Page 23 4. No display No display (LED white) Check TV is under control and power Replace the main board on/off by remote control and power key? Check the backlight is “On”? Check the LVDS cable Check the B/L signal is available? Reinsert or replace the LVDS cable Replace main board...
  • Page 24 5. Sound problem No sound or sound abnormal Check the audio source connection and the TV system are correct? Reinsert the audio cable or change the TV system Check the TV is muted, adjust the volume or enter the menu to reset? Enter factory mode to do “Reset”...
  • Page 25 6. Remote control malfunction Remote Control malfunction Check the remote control battery is Replace the battery not properly placed or no power? Use the other remote controls Replace the remote control Whether the IR board is Replace the IR board abnormal? Replace the main board...
  • Page 26 7. OSD is unstable or can’t work normally OSD is unstable or can’t work normally Key board connected properly? Reconnect the key board Replace the button function Buttons are OK? Replace the key board Key board is OK? Enter factory mode to do “Reset” Replace the main board...
  • Page 27: Pcb Layout

    6. PCB Layout 6.1 Main Board 715G3759M02000005K...
  • Page 29: Power Board

    6.2 Power Board 715G3754P01W30003H...
  • Page 32: Key Board

    6.3 Key Board 715G3303 2 6.4 IR Board 715G3963R01000004S...
  • Page 33: Adjustment

    7. Adjustment/FW Upgrade/EDID 7.1 ADC Adjustment It’s no need to adjust the white balance for this model, do ADC only. Step1: Turn on the TV, press “Menu”, then press number key 1 Æ 9 Æ 9 Æ 9 and “ENTER”, it will achieve the factory mode.
  • Page 34: Fw Upgrade

    FW version. The first and second parts of FW name must be the same as the TV, and the third part must not be the same as TV current FW version. Or the FW upgrade can’t continue. Take Haier L19C1120 for example: Brand: Haier Customer model name FW version: V2.01 Step 2: F/W Upgrad 2.1 AC on (Power plug Figure 2.1/2.2)
  • Page 35 2.4 When TV detects the USB memory, there is a prompt frame appearing on the screen as figure 2.6, press “ENTER” key(on the Navigation Keys on the Remote control, as follows Figure 2.7 to select “Yes” option to download F/W(Figure 2.8). Take Haier L19C1120 for example: Figure 2.6...
  • Page 36 2.5 TV will upgrade automatically. Note: When Upgrade on the process, please don’t Power-Off! (Figure 2.8) Figure 2.8 2.6 When upgrade 100% and prompt for Upgrade Success info, remove the USB Drive and press “ENTER” key to reset TV (Figure 2.9) Figure 2.9 Step 3: Check the F/W version and reset to default.
  • Page 37 3.2 Check the F/W version on the second row of the factory mode info. If F/W version is incorrect, please upgrade again as above steps, else let’s go to Step 3.3. Take Haier HLC24XLE2 for example: Figure 3.2 3.3 If the FW version is correct, please do factory reset.
  • Page 38: The Writing Vga & Hdmi Edid

    7.3 The Writing VGA & HDMI EDID Step1. Ready for writing EDID Tool: 715G2005-C2 Cable: a LPT cable, a VGA cable, a DVI to HDMI cable and a 12V DC adapter. 715G2005-C2 male to male LPT cable VGA cable DVI to HDMI cable Step2.
  • Page 39 Step3. Install TPV edid tool. Take Haier LY19Z6 for example: 1. Double click this icon to install. 2. Double click this icon to run. This red frame contents detail information in VGA EDID file. 1. Click here to open this interface.
  • Page 40 Step4. Click “FPD” to open another interface as follows. Take Haier LY19Z6 for example: 1. Tick LPT1 2. Click here to read file as figure 4.2 2. Click “open” to read the “.dat” file. figure 4.2...
  • Page 41 Step5. Click “write EDID” to write EDID. If display “NG” in the yellow blank, which represent writing failly. Please check the whether the connection of tool and cables is nomal and retry. Another way is to change a new ISP board and retry. Take Haier LY19Z6 for example: 2. ”OK” represents writing successfully.
  • Page 42 Step6. Write HDMI EDID. Connection for writing HDMI EDID. Connect to TV HDMI port. Connect to PC LPT port. 12V DC input Notice: When writing HDMI EDID, the TV must be AC on, or the process can’t continue, and will prompt “NG”...
  • Page 44: Wiring Diagram

    5 Pin...
  • Page 48 1 2 3 4...

This manual is also suitable for:

L19L22L26c112L19c1120L22c1120

Table of Contents