Contents Contents How to select the picture mode ........15 Warning How to customize your own picture status....15 Sound Control Functions ........16 Important Safety Instructions How to choose Digital tone mode....... 16 How to customize your own sound status....17 Panel Control and Rear Terminals Timer Functions ..........18 Control...
Warning Warning WARNING RISK ELECTRIC SHOCK DO NOT OPEN WARNING: TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE. REFER TO QUALIFIED SERVICE PERSONNEL. * To avoid electric hazards, it is strongly suggested that the back cover not be opened, as there is no any accessory inside the casing.
Panel Control and Rear Terminals Control Panel Control and Rear Terminals Control - This is a simplified representation of front panel. - Here shown may be somewhat different from your TV. Panel Control Rear Terminals Control GOMPONENY PC AUDIO VIDEO L AUDIO R VIDEO L AUDIO R...
Remote Control Remote Control Battery loading 1. Slide open the cover of the battery compartment on the back of the remote controller. 2. Load two 7# (AAA) alkaline batteries in the compartment, (plus and minus poles to respective mark) 3. Replace the cover of the battery compartment. Precautions Make sure that two AAA alkaline batteries are loaded.
Remote Control Function Remote Control Function - The remote control cannot be operated unless the batteries are properly loaded. - When using the remote control, aim it at the remote control sensor on the TV. Function introduction Press this key to start TV from standby mode, press it again to return to standby 1 POWER mode.
External Equipment Connections External Equipment Connections Antenna Connection - Antenna or Cable Service without a Cable Box Connections. - For optimum picture quality, adjust antenna direction if needed. Note: * It is recommended that you'd better use 75 coaxial cable to remove the disturbance caused by airwave.
External Equipment Connections Choose Your Connection select the source, press the button to confirm. There are several ways to connect your television, DVD Setup depending on the components you want to connect and the quality of the signal you want to achieve. The following are examples of someways to connect your TV.
External Equipment Connections available. Then, make the corresponding audio change the refresh rate to another rate or adjust the brightness and contrast on the menu until the picture connections. is clear. If the refresh rate of the PC graphic card can not be changed, change the PC graphic card or How to use consult the manufacturer of the PC graphic card.
External Equipment Connections External Equipment Connections / Basic Receiving and Playing Operations In the manual, the OSD (on screen display) may be Note different from your TV’s because it is just an example to Component, PC, HDMI input sources cannot be help you with the TV operation.
Basic Receiving and Playing Operations option, and then press OK to enter submenu. to confirm the switching to TV input terminal. After switching, the signal source menu disappears, and at the Channel Edit upper right corner of screen displays the information of current signal source.
Basic Receiving and Playing Operations If you want to recover the skipped channel Exchange 1. Use Direct-digit Choosing button to select the number of the channel to be recovered. Press MENU on the remote control unit or MENU on 2. Do the above steps again. the TV’s front panel to display main menu, and then 3.
Basic Receiving and Playing Operations the TV set to adjust the volume level. The range is Due to different TV signal inputs, some items may need 0~100. When the volume buttons are pressed the to be adjusted. The following makes a description by only taking TV signal as an example.
Basic Receiving and Playing Operations Reset Contrast Return to factory default settings. Press This will adjust the intensity of bright parts in the select OK or Cancel, Press OK to affirmance. picture but keep the dark parts unchanged. Brightness Palette Standard This will adjust the light output of the complete Reset...
Basic Receiving and Playing Operations How to customize your own Sound status Press MENU to display main menu on the screen, and then press to select the Sound menu, afterwards press OK/ to enter the option to be adjusted. Press to select the option to be adjust.
Basic Receiving and Playing Operations Timer Functions Setting of Current Time The current time is calculated from the moment upon turning the TV on. At first, check whether the time indicated on the TV's clock is consistent with the standard time of your time zone;...
Basic Receiving and Playing Operations Press MENU on the remote control unit or MENU OSD Menu on the TV's front panel to display the main menu, Press to select the OSD Menu option. and then press to select the Timer menu, Press to enter the submenu.
Basic Receiving and Playing Operations Adjust Menu Press to set Demo Off/Demo /Demo The TV can be used as a display, and you may adjust Background relevant settings. Press to set ON or OFF, if you select ON, the TV screen will be black if no signals are available.
Page 21
Basic Receiving and Playing Operations Press H. LOCK, the TV screen will display Enter Password to the preset source upon turning on. For example, to prompt the user to enter a correct password by when the Preset Source is set as YP , the TV pressing corresponding numerical keys;...
Maintenance/Troubleshooting Press SOURCE on the remote control unit to select is set as OFF and max volume returns to 100 (except password). USB option. C Bus Insert USB equipment into corresponding USB interface 2s after starting the system. It is no need for user to select the after-sale service option.
Specification/Formatl You can choose the photos or music in different After entering USB main interface, press files to play together. select MUSIC item. Press OK to confirm the selection and enter the Playing a Picture music file list. After entering USB main interface, press select PHOTO item.
Specification/Format Maintenance Maintenance Early malfunctions can be prevented. Careful and regular cleaning can extend the amount of time you will have your new TV. Be sure to turn the power off and unplug the power cord before you begin any cleaning. Press and OK button to select the text you want to play, and then press OK button to play the...
This is not defect. If the 572x170x413mm 4.2Kg LE24T3 TV set is used in an area 2,400 meters above the sea level where the air pressure is below 750hpa, the picture on the screen maybe affected and a muffled...
Maintenance / Troubleshooting/Specification Note 576i/576p Design and specifications are subject to change 720p 50/60 without notice. The dimension in this manual is a approximation. 1080i 50/60 Format Sequence Refresh Format Number Frequency (Hz) 480i/480p 576i/576p 720p 50/60 1080i/1080p 50/60 sequence H-Frequency V-Frequency Format...
Page 27
Specification / Format LCD television Owner’s Manual...