Table of Contents
Advertisement
IMPORTANT: THe oooR opENER pRovrDES FoR
p o s r l v E c L o s r N G o F T H E D o o R . A t - l e x t s r t r u c
DooR LocKs MUST BE MADE tNopERnrtve. lr exlst-
I N G D O O R L O C K S A R E L O C K E D W H I L E T R Y I N G T O U S E T H E
OPENER, DAMAGE TO OPENER AND DOOR COULD RESULT.
Pin or screw the existing lock mechanism in the "open"
(unlocked) position. If necessary, the catch latches may be
Pin or Screw
in Unlocked
Position
repositioned or the complete lock assembly
Because of the many styles of door locks,
show only two of the more common types.
IMPORTANT: lr rs rruponrerur
A N D C O R D S , T H A T C O U L D C A U S E
BE REMOVED FROM THE DOOR.
_-- Remove
*'t
Lock Plates -
may be removed.
the illustrations
T H A T A L L R O P E S
E N T A N G I - E M E N T ,
Both Ends ol
Doors
FrG. 29
FrG. 30
35 Feet of Wrre
Red Alignment
Light
Your garage door opener is supplied with an infrared beam
sensor that sends an invisible beam of light from the sending
unit to the receiving unit across the pathway of the door.
Please read and follow these instructions carefully.
I M P O R T A N T : T H e D o o R
O P E N E R W I L L N O T O P E R A T E
U N T I L T H E B E A M S E N S O R I S
C O N N E C T E D T O T H E P O W E R U N I T A N D
P R O P E R L Y A L I G N E D . T H e t n v t s t a r e e e a u o r
L I G H T M U S T N O T B E O B S T R U C T E D , O T H E R W I S E , T H E
D O O R C A N B E C L O S E D B Y M A I N T A I N I N G C O N S T A N T
PBESSURE ON THE WALL-MOUNTED PUSHBUTTON ONLY.
T H e r n n r u s u t r r E R c A N N o r B E u s E D T o c l o s E T H E
ooon. Tue DooR cAN. BE opENED uslNc EITHER THE
H A N D - H E L D T R A N S M I T T E R O R W A L L - M O U N T E D
P U S H B U T T O N E V E N I F T H E B E A M I S N O T A L I G N E D O R
C O N N E C T E D T O T H E P O W E R U N I T . P U L L E M E R G E N C Y
RELEASE CORD TO DISCONNECT DOOR FROM OPENER,
T H E N M A N U A L L Y C L O S E G A R A G E D O O R B E F O H E
CONTINUING.
Before beginning beam sensor mounting, identify
which side of the garage door opening (if any) the sun
is "likely"
to shine into. Since sunlight may cause
undesirable operation, you should plan to mount the
small sending unit (not the receiving unit) on the side
of the door opening exposed to the sun.
Page 14
A. Begin by attaching the sending and receiving units to the
mounting brackets using the four thumb screws provided.
The thumb screws go through the bracket and thread into
the two holes on the bottom of the units. Do not tishten at
this time. See Figure 30.
* - S e n d i n g U n i t
Mounting Bracket
2 Thumb
Screws
Receiving
Unit
2 Thumb
Screws
2 Wood
Screws for
Mounting
1 4 8 . 3
Hide quick links:
Advertisement
Table of Contents
