Accessories And Parts; Furnished Accessories; Licensing Information; Information To The User - Shure PSM 900 Instruction Manual

ACCESSORIES AND PARTS

Furnished Accessories

P9R Antenna
470–542 MHz
596–692 MHz
670–830 MHz
830–952 MHz
P9T Antenna
470–530 MHz
500–560 MHz
518–578 MHz
578–638 MHz
638–698 MHz
690–746MHz
740–814 MHz
774–865 MHz
900–1000 MHz
Front Mount Antenna Cable
Zipper Bag
Rackmount Bracket, Long
Rackmount Bracket, Short
Link Bar
Hardware Kit (Rackmounting
Screws)
Bumper Kit
Energy Efficient Switching Power Supply
Brazil
Argentina
Europe
United Kingdom
Austrailia/New Zealand
China
Taiwan
Japan
UA700
UA720
UA730
UA740
UA820G
UA820G7
UA820H4
UA820J
UA820L3
UA820B
UA820Q
UA820A
UA820X
95A9023
95A2313
53A8612
53A8611
53B8443
90AR8100
90B8977
USA PS41US
PS41BR
PS41AR
PS41E
PS41UK
PS41AZ
PS41CHN
PS41TW
PS41J
P9T, P9RA
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du
Canada.
Meets requirements of EMC standards EN 300 422 Parts 1 and 2 and EN 301 489
Parts 1 and 9.
Meets essential requirements of European R&TTE Directive 99/5/EC, eligible to bear
the CE mark.
P9T
Certified under FCC Part 74. (FCC ID: DD4P9TA, DD4P9TB, DD4P9TC,
DD4P9TD, DD4P9TJ). Certified by IC in Canada under RSS-123 and RSS-102. (IC:
616A-P9TA, 616A-P9TB, 616A-P9TC, 616A-P9TD).
P9RA
Approved under the Declaration of Conformity (DoC) provision of FCC Part
15. Certified in Canada by IC to RSS-123. (IC: 616A-P9RAA, 616A-P9RAB,
616A-P9RAC, 616A-P9RAD).
Operation of this device is subject to the following two conditions: (1) this device may
not cause interference, and (2) this device must accept any interference, including
interference that may cause undesired operation of the device.
The CE Declaration of Conformity can be obtained from Shure Incorporated or any
of its European representatives. For contact information please visit www.shure.com
The CE Declaration of Conformity can be obtained from: www.shure.com/europe/
compliance
Authorized European representative:
Shure Europe GmbH
Headquarters Europe, Middle East & Africa
Department: EMEA Approval
Jakob-Dieffenbacher-Str. 12
75031 Eppingen, Germany
Phone: +49-7262-92 49 0
Fax: +49 7262-92 49 11 4
Email: EMEAsupport@shure.de

LICENSING INFORMATION

Licensing: A ministerial license to operate this equipment may be required in certain
areas. Consult your national authority for possible requirements. Changes or modi-
fications not expressly approved by Shure Incorporated could void your authority to
operate the equipment. Licensing of Shure wireless microphone equipment is the
user's responsibility, and licensability depends on the user's classification and ap-
plication, and on the selected frequency. Shure strongly urges the user to contact the
appropriate telecommunications authority concerning proper licensing, and before
choosing and ordering frequencies.

Information to the user

This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installa-
tion. This equipment generates uses and can radiate radio frequency energy and,
if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that interfer-
ence will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one
or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment to an outlet on a circuit different from that to which the
receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Note: EMC conformance testing is based on the use of supplied and recommended
cable types. The use of other cable types may degrade EMC performance.
Changes or modifications not expressly approved by the manufacturer could
void the user's authority to operate the equipment.
9