Download Print this page

National Semiconductor LMX9820A User Manual

Simply blue module kit

Advertisement

Quick Links

LMX9820ADEV:
LMX9820A Simply Blue Mod-
ule Kit User's Guide
Scope
The Simply Blue module kit (LMX9820ADEV) is for evalua-
tion and demonstration of the National Semiconductor
LMX9820A Simply Blue Serial Port module. This user's
guide provides platform setup procedures and configura-
tion options for the Simply Blue module kit.

General Description

The Simply Blue module kit contains two boards:
Texas Motherboard Rev. 2
— Serial connector and RS-232 interface circuitry
— JTAG connector and interface circuitry
— Audio Codec interface for Sedona Board
— Three power regulators
— Power and link status LED indicators
LMX9820A Simply Blue Module Kit
National Semiconductor ia a registered trademark of National Semiconductor Corporation.
Bluetooth is a trademark of Bluetooth SIG, Inc. and is used under license by National Semiconductor.
For a complete listing of National Semiconductor trademarks, Visit www.national.com/trademarks.
© 2003 National Semiconductor Corporation
National Semiconductor
User's Guide
December 2004
Revision 0.2
— USB connector and interface circuitry (not used for
®
LMX9820A)
— Test points of baseband and radio signals
— 50-pin connector (to Austin Daughterboard)
Austin Daughterboard Rev. 1
— LMX9820A serial port module
— On-board 12 MHz crystal
— On-board 32.768 kHz crystal for low power modes
— Internal use only test points of module signals
— SMA connectors for antenna and clock
— 50-pin connector (to Texas motherboard)
Sedona Audio Codec Daughterboard Rev. R1B
— 2 OKI Codecs, default operation
— 2 Motorola Codecs, supported
— 1 Speaker connection
— 2 Mic connections, only 1 used
www.national.com

Advertisement

loading

Summary of Contents for National Semiconductor LMX9820A

  • Page 1: General Description

    Scope The Simply Blue module kit (LMX9820ADEV) is for evalua- tion and demonstration of the National Semiconductor LMX9820A Simply Blue Serial Port module. This user’s guide provides platform setup procedures and configura- tion options for the Simply Blue module kit.
  • Page 2 Texas Motherboard, Revision 2 Austin Daughterboard, Revision 1 www.national.com (Confidential) Revision 0.2...
  • Page 3 Speaker Sedona Daughterboard, Revision 1 Revision 0.2 (Confidential) www.national.com...
  • Page 4: Kit Contents

    Kit Setup KIT CONTENTS The Simply Blue module kit (LMX9820ADEV) contains the following items: • Texas Motherboard • Austin Daughterboard • Sedona Board • Null modem cable • 100V - 240V AC to 5V DC power supply • Antenna • CD-ROM containing documentation and software REQUIREMENTS AND SETUP 1.2.1 Basic Requirements...
  • Page 5 Figure 1-1. PC - Simply Blue Module Connection 12 MHz (Optional) 5V Power Austin Texas Motherboard Supply TX/RX 50 pin Daughterboard Connector Antenna Speaker Sedona Codec Daughterboard Mic/ Audio In Figure 1-2. System Connection Diagram Figure 1-3. Simply Blue Default Directory Revision 0.2 (Confidential) www.national.com...
  • Page 6 Figure 1-4. Simply Blue Shortcut www.national.com (Confidential) Revision 0.2...
  • Page 7 Audio Codec Optional Test Point - User defined (not used for LMX9820A) Name Description Reset# - Reset LED for LSTAT_0 (not used for LMX9820A) LED for LSTAT_1 - When illuminated, firmware has loaded properly LED for VCC LED for IOVCC LED for UVCC LED for TX/RX Activity Revision 0.2 (Confidential)
  • Page 8 P3 DP9 Serial Connector P3 is a DP9 serial port connector that interfaces to the LMX9820A’s full duplex UART. It supports up to 921.6 kbps transfer rates. Refer to Table 2-4 for selecting and setting the UART and transfer rate.
  • Page 9 Input Input Mode ISP Firmware Upgrade Normal Operation Refer to the LMX9820A datasheet for additional mode boot-up details. A weak internal pull-up pulls ENV0/1 to VCC. 2.1.7 J12 Audio Header (4x2) and J23 Test Point J12 provides access to the Advanced Audio Interface (AAI) signals that connect an external codec.
  • Page 10 National LMX9820A Serial Port Module - Reference the device datasheet. 12 MHz Crystal - Reference the crystal device datasheet and the LMX9820A datasheet for details. 32.768 kHz Crystal for low power modes - Reference the crystal device datasheet and the LMX9820A datasheet for more details.
  • Page 11 2.2.5 J3 SMA RF Signal Connector Connect antenna or test equipment to the SMA. RF_SIGNAL Figure 2-3. J3 SMA Connection - Single TX/RX 2.2.6 J5 Optional External Clock An optional external clock can be used. C29, 100 pF, must be placed for proper operation. It is recommended to set the signal generator to 12 MHz @ 2 dBm output.
  • Page 12 SEDONA CODEC DAUGHTERBOARD SUMMARY The Sedona codec Rev. R1B Daughterboard is populated with a 2 OKI codecs and 2 Motorola codes. Oki codec is the only supported device. Also, no configuration is needed for board so full details are not provided. Reference the schematic, BOM, and board for more details.
  • Page 13: Life Support Policy

    LIFE SUPPORT POLICY NATIONAL’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT AND GENERAL COUNSEL OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein: 1. Life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body, or (b) support or sustain life, and whose failure to perform when properly used in accordance with...

This manual is also suitable for:

Lmx9820adev