Page 1
VCC-6580P INSTRUCTION MANUAL BEDIENUNGSANLEITUNG MANUEL D’INSTRUCTIONS COLOUR CCD camera CCD-Farbkamera Caméra CCD COULEUR About this manual A propos de ce manuel Before installing and using the camera, please read this manual Avant d’installer et d’utiliser la caméra, veuillez lire ce carefully.
Depending on the conditions of use, installation and environment, FEATURES please be sure to make the appropriate settings and adjustments. If you need help with installation and/or settings, please consult your dealer. • Built-in interline transfer method 1/3" CCD, approx. 470,000 CONTENTS picture elements •...
Disconnect the power greasy smoke or steam, where the dampness may get too high, or cord immediately, and consult your dealer (or a Sanyo Authorized where there is a lot of dust.
PARTS NAMES Power indicator (POWER) Comes on when the power to the camera is on. Video output connector (VIDEO OUT: BNC type) Connect this connector to a device such as a monitor, digital video recorder or time-lapse VCR with a VIDEO IN connector.
Page 5
PARTS NAMES Lens mount cap The cap is installed to protect the lens mount section. Remove the lens mount cap before installing a lens (sold separately). Flange-back adjustment screw (FLANGE BACK ADJ.) Flange-back lock screw (FLANGE BACK LOCK) Camera installation bracket The bracket can be fixed at the top or bottom of the camera.
Connect the lens plug to the lens iris output connector (LENS) on the side of the camera. type lens Depending on the type of lens, the shape of the lens plug may differ. In this case, consult your dealer or an Authorized Sanyo Service Center. English...
Page 7
MOUNTING THE LENS LENS terminal Lens iris output terminal which is used to connect the lens plug when the auto-iris lens is attached. Brake coil (–) Drive coil (+) Brake coil (+) Drive coil (–) Flange-back adjustment This normally does not need adjustment. If the picture is out of focus at the telephoto position, adjust the flange-back position as described below.
CONNECTIONS (Video signal connections) : VIDEO IN : VIDEO OUT Coaxial cable type and maximum length Basic connection for monitoring or recording • Cable type RG-59U (3C-2V), 250 m maximum. The peripheral devices (monitor, digital video recorder, • Cable type RG-6U (5C-2V), 500 m maximum. time-lapse VCR, etc.) and cables are sold separately.
SETTINGS The illustration shows the factory default settings for the switches in the camera setup section. Control name Position High speed electronic shutter setting (ES) 1/50 sec. EI HI VR302 VR303 VR301 Iris function setting (IRIS) Electronic iris: EI/Auto iris: AI Lens iris level adjustment (LEVEL) adjustable LSB AI NOR NOR M...
Page 10
SETTINGS High speed electronic shutter setting Iris function setting Normally, the speed setting switches for the high speed electronic Change iris setting when using either lens below. shutter are all set to the down position. This sets the electronic EI: (for indoor use) shutter speed to 1/50 sec.
SETTINGS Gain control Backlight compensation setting For adjusting the sensitivity of the camera. Use this setting for This camera has three different shooting in dark environments. backlight compensation modes. Change the mode to match the HI: Increased sensitivity allows shots to be taken in backlight condition.
SETTINGS White balance adjustment Sync setting Normally the switch 9 (WB) is set to the down (ATW) position and LL: Line-Lock the white balance is adjusted automatically. If a manual white balance Synchronizes the unit with power frequency when two or more adjustment is necessary, follow the steps below.
This camera is a precision instruments and if treated with care, will provide years of satisfactory performance. However, in the event of a problem, the owner is advised not to attempt to make repairs or open the cabinet. Servicing should always be referred to your dealer or Sanyo Authorized Service Centre.
SPECIFICATIONS Camera: Scanning system Environmental conditions PAL standard Temperature: –10° C ~ +50° C (14° F ~ 122° F) (625 TV lines, 25 frames/sec.) Humidity: less than 90%RH (no condensation) Interlace Power supply 2:1 interlace 220 – 230 V AC, 50 Hz Image device Power consumption 1/3 inch solid state image device CCD...