Bosch GBM 13-2 RE Professional Original Instructions Manual page 14

14 | English
Technical Data
Rotary drill
Article number 3 601 ... ... AB2 002 ... AB2 000 ... AB2 001 ... AB2 030 ... AB2 060 ... AB2 070 ... AB2 040
Rated power input
Output power
No-load speed
– 1st gear
– 2nd gear
Rated speed
– 1st gear
– 2nd gear
Rated torque
(1st/2nd gear)
Spindle collar dia.
Speed preselection
Speed control
Right/left rotation
Overload Clutch
Keyless chuck with
securing ring
Keyless Chuck
Key type drill chuck
Maximum drilling diam-
eter (1st/2nd gear)
– Steel
– Wood
– Aluminium
Chuck clamping range
Weight according to
EPTA-Procedure
01/2003
Protection class
Declaration of Conformity
We declare under our sole responsibility that the product de-
scribed under "Technical Data" is in conformity with all rele-
vant provisions of the directives 2011/65/EU, until
19 April 2016: 2004/108/EC, from 20 April 2016 on:
2014/30/EU, 2006/42/EC including their amendments and
complies with the following standards: EN 60745-1,
EN 60745-2-1.
Technical file (2006/42/EC) at:
Robert Bosch GmbH, PT/ETM9,
70764 Leinfelden-Echterdingen, GERMANY
Henk Becker
Executive Vice President
Engineering
Robert Bosch GmbH, Power Tools Division
70764 Leinfelden-Echterdingen, GERMANY
Leinfelden, 23.06.2015
1 609 92A 1CG | (23.6.15)
W 750
W 353
-1
min 0 – 1000 0 – 1000
-1
min 0 – 3000 0 – 3000
-1
min 500
-1
min 1750 1750
Nm 6.8/2.5 6.8/2.5
mm 43





–
–
mm 13/8 13/8
mm 32/20 32/20
mm 20/12 20/12
mm 1 – 13 1 – 13
kg 2.4
/II
Helmut Heinzelmann
Head of Product Certification
PT/ETM9
750 750 750
353 353 353
0 – 1000 0 – 1000
0 – 3000 0 – 3000
500 500 500
1750 1750
6.8/2.5 6.8/2.5
43 43
 
 
 
 
– –

–

–
13/8 13/8
32/20 32/20
20/12 20/12
1 – 13 1 – 13
2.4 2.4
/II /II
Assembly
Auxiliary Handle (see figure A)
 Operate your machine only with the auxiliary handle 9.
The auxiliary handle 9 can be set in 12 positions to achieve a
safe and low-fatigue working stance.
Turn the bottom part of the auxiliary handle 9 in rotation di-
rection  and push the auxiliary handle 9 forward until you
can pivot it to the desired position. Then pull the auxiliary han-
dle 9 back again and tighten it by turning the bottom part of
the auxiliary handle in rotation direction .
Adjusting the Drilling Depth (see figure A)
The required drilling depth X can be set with the depth stop
10.
Turn the bottom part of the auxiliary handle 9 in anticlockwise
direction and insert the depth stop 10.
Pull out the depth stop until the distance between the tip of
the drill bit and the tip of the depth stop corresponds with the
desired drilling depth X.
750 710
374 365
0 – 1000 0 – 1000
0 – 3000 0 – 3000
500 500
1750 1750
6.5/2.2 6.5/2.2
43 43
 
 
 
 
– –
 
– –
13/8 13/8
32/20 32/20
20/12 20/12
1 – 13 1 – 13
2.4 2.4 2.4
/II /II
GBM 13-2 RE
750
353
0 – 1000
0 – 3000
500
1750
6.8/2.5
43 43
 
 
 
 

–

–
– –
13/8
32/20
20/12
1 – 13
2.4
/II /II
Bosch Power Tools