Wiring Diagrams - Daikin FH35GZ Technical Data Manual

5

Wiring diagrams

FH35∼60BZ
Notes
1. D : Terminal F, H : Connector
b : Protective earth (screw)
2. B : Field wiring
3. In case using central remote controller, connect it to the
unit in accordance with the attached instruction manual.
4. X24A is connected when the remote controller kit is
being used.
5. Remote controller model varies according to the
combination system, confirm technical materials and
catalogs, etc. before connecting.
6. In case installing the drain pump, remove the jumper
connector of X15A and execute the additional wiring for
float switch and drain pump.
7. Ground the shield of the remote controller cord to the
indoor unit of the FH-BVE type.
8. Symbols show as follows Red:red, Blk:black, Ylw:yellow,
Org:orange, Gry:gray, Prp:purple, Blu:blue
9. Confirm the method of setting the selector switch (SS1,
SS2) by installation manual and engeneering materials,
etc.
1-RED, 2-WHITE, 3-BLACK
33A Limit switch (swing flap)
A1P Printed circuit board
A2P Printed circuit board
(Transformer 220-240V/16V)
C1R Capacitor (M1F)
F1U Fuse (250V,5A)
HAP Light emitting diode (service monitor green)
M1A Motor (swing flap)
10
M1F Motor (indoor fan)
Q1F Thermo switch (M1F embedded)
5
FHY35∼45GZ7V1
Notes
1. Use copper conductors only.
2. When using the central remote control, see
manual for connection to the unit.
3. The remote controller model varies according to
the combination system.
4. When installing the drain pump, remove the
jumper wire of X15A and make the additional
wiring for the float switch and the drain pump.
5. M1S and 33S are only attached to the indoor unit
of the heat pump type
g Field wiring D Terminal
a
: Connector
c
: Wire clamp
b
: Protective earth (screw)
Colours
BLK: Black/ PPL: purple/ BLU: Blue/
WHT: White/ RED: Red/ GRN: green/
GRY: grey/ YLW:Yellow
33S Limit switch (swing flap)
A1P Printed circuit board
A2P Printed circuit board (transformer 220-240V/16V)
C1R Capacitor (fan)
H1P,H2P Light emitting diode
M1F Motor
M1S Motor
Q1F Thermo switch (M1F embedded)
R1T Thermistor (air)
R2T Thermistor (coil)
14
• Ceiling Suspended Unit • R-407C • FH(Y)-GZ/BZ/FHYP-B
Note) 4
Receiver / display unit
R1T Thermistor (air) R1T Thermistor (air)
R2T Thermistor (coil) SS1 Selector switch (main/sub)
RyA Magnetic relay (M1A) Infrared remote control
Receiver / display unit
RyC Magnetic relay (outdoor unit compressor)
A3P Printed circuit board
RyP Magnetic relay (M1P)
A4P Printed circuit board
SS1 Selector switch (emergency)
BS Push button (on/off)
X1M Terminal strip
H1P Light emitting diode (service monitor red)
X2M Terminal strip
+
H2P Light emitting diode (service monitor green)
Current detect circuit
=
H3P Light emitting diode (service monitor red)
Phase control circuit
H4P Light emitting diode (service monitor orange)
Wired remote control
Outdoor
Details of wired remote control
(optional accessory)
(for heat pump type)
RyA Magnetic relay (swing flap) X30A
RyP Magnetic relay (drain pump) X33A
SS1 Selector switch (emergency) X35A
X1M,X2M Terminal strip Infrared remote control
PC Phase control circuit BS1
RC Signal receiver BS2
TC Signal transmission circuit BS3,BS8
Connector for optional parts BS4,BS9
X15A Connector (float switch) BS5
X25A Connector (drain pump) BS6
• Split - Sky Air • Indoor Units
To outdoor
unit
SS1 Selector switch (main/sub)
SS2 Selector switch (wireless address set)
Connector for optional parts
X15A Connector (float switch)
X25A Connector (drain pump)
X30A Connector (interface adaptor for sky air series)
X33A Connector (adaptor for wiring)
X35A Connector (group control adaptor)
Switch box
Indoor
Note 4 Note 5
Simultaneous operation system
(for cooling only
Remote control (master)
type)
Connector (interface adaptor for sky air series) BS7
Connector (adaptor for wiring) BS11
Connector (group control adaptor) BS12
BS14
On/Off button H1P
Timer mode start/stop button LCD
Programming time button SS1
Temperature setting button Adaptor for wiring
Air flow direction adjust button RyC,RyF
Operation mode selector button
Wired remote
Note) 4
Note) 6
Wired remote
control
Terminals for operation
indicator
Adaptor for wiring
(slave)
Switch box
Timer on/off button
Fan speed control button
Inspection/test operation button
Filter sign reset button
Light emitting diode (service monitor red)
Liquid crystal display (LCD)
Selector switch (main/sub)
Magnetic relay
control
Note) 7
Note) 6
3D027501-1
2TW21006-1C