D-Link DGS-1100-16/ME Reference Manual
  1. Manuals
  2. Brands
  3. D-Link Manuals
  4. Switch
  5. DGS-1100-16/ME
  6. Reference manual

D-Link DGS-1100-16/ME Reference Manual

Dgs-1100/me series metro ethernet managed switch
Hide thumbs
Table of Contents

Advertisement

Quick Links

D-Link™ DGS-1100/ME
Metro Ethernet Managed Switch

CLI Reference Guide

V1.0

Advertisement

Table of Contents
loading

Related Manuals for D-Link DGS-1100-16/ME

Summary of Contents for D-Link DGS-1100-16/ME

  • Page 1: Cli Reference Guide

    D-Link™ DGS-1100/ME Metro Ethernet Managed Switch CLI Reference Guide V1.0...
  • Page 2 Reproduction in any manner whatsoever without the written permission of D-Link Corporation is strictly forbidden. Trademarks used in this text: D-Link and the D-Link logo are trademarks of D-Link Corporation; Microsoft and Windows are registered trademarks of Microsoft Corporation. Other trademarks and trade names may be used in this document to refer to either the entities claiming the marks and names or their products.

  • Page 3: Table Of Contents

    Table of Contents INTRODUCTION ..............................1 PRODUCT INTRODUCTION ........................... 2 DGS-1100-16/ME ................................. 2 Front Panel ..................................2 Rear Panel ..................................2 DGS-1100-18/ME ................................. 3 Front Panel ..................................3 Rear Panel ..................................3 DGS-1100-24/ME ................................. 4 Front Panel ..................................4 Rear Panel ..................................4 DGS-1100-24P/ME ................................
  • Page 4 ping ......................................26 create time_range .................................26 delete time_range .................................27 show time_range ..................................28 config telnet auto_logout..............................28 show telnet ...................................29 config firmware ..................................29 show firmware..................................29 create iproute ..................................30 delete iproute ..................................30 config command_prompt ..............................31 SWITCH PORT COMMANDS ..........................32 config ports ..................................32 show ports ....................................33 LOOPBACK DETECTION COMMANDS .......................
  • Page 5 clear counters ..................................53 clear log ....................................54 show log ....................................54 enable syslog ..................................55 disable syslog ..................................55 show syslog ..................................56 config syslog host.................................56 show syslog host ..................................58 cable diagnostic port ................................59 FORWARDING DATABASE COMMANDS ......................60 create fdb ....................................60 create multicast_fdb ................................61 config multicast_fdb ................................61 config fdb aging_time ................................62 delete fdb ....................................63...
  • Page 6 config management_vlan ..............................83 show management_vlan ...............................84 config port_vlan ...................................84 show port_vlan ..................................85 enable pvid auto_assign ...............................85 disable pvid auto_assign ..............................86 show pvid auto_assign .................................86 BASIC IP COMMANDS ............................87 config ipif System ................................87 show ipif....................................88 IGMP SNOOPING COMMANDS..........................89 enable igmp_snooping .................................90 disable igmp_snooping.................................90 show igmp_snooping ................................91 config igmp_snooping ................................91...
  • Page 7 .....................................133 ZONE DEFENSE COMMANDS ........................... 135 enable zone_defense ................................135 disable zone_defense ................................135 show zone_defense ................................136 D-LINK DISCOVERY PROTOCOL COMMANDS ....................137 enable ddp ..................................137 disable ddp ..................................137 config ddp report_time ...............................138 show ddp ....................................138 POE COMMANDS ..............................140 config poe system ................................140...
  • Page 8 show poe ports ...................................142 SURVEILLANCE VLAN COMMANDS ........................ 144 enable surveillance_vlan ..............................144 disable surveillance_vlan ..............................145 config surveillance_vlan priority ............................145 config surveillance_vlan aging_time ..........................146 config surveillance_vlan oui ..............................147 show surveillance_vlan global ............................148 show surveillance_vlan oui ..............................148 show surveillance_vlan device ............................149 VOICE VLAN COMMANDS ..........................151 enable voice_vlan ................................151 disable voice_vlan ................................152 config voice_vlan priority ..............................152...
  • Page 9 L2 Features ..................................170 L2 Multicasting ................................. 2 VLAN ....................................2 QoS (Quality of Service) ..............................2 Security ..................................... 2 Management ..................................2 Power Saving ..................................2 APPENDIX C – RACK MOUNT INSTRUCTIONS ....................2...

  • Page 10: Introduction

    DGS-1100/ME Metro Ethernet Managed Switch CLI Reference Guide INTRODUCTION The DGS-1100-16/ME consists of 16-ports 10/100/1000Mbps. The DGS-1100-18/ME consists of 16-ports 10/100/1000Mbps ports + 2-ports 1000Mbps SFP The DGS-1100-24/ME consists of 24-ports 10/100/1000Mbps. The DGS-1100-24P/ME consists of 12-ports 10/100/1000Mbps PoE + 12-ports 10/100/1000Mbps.

  • Page 11: Product Introduction

    By using EEE compliant devices, such as PCs and servers, the network can save energy without compromising any performance. Even when connecting to legacy devices which do not support IEEE 802.3az, D-Link Green Technologies can reduce power consumption by changing the power state of the link.

  • Page 12: Dgs-1100-18/Me

    DGS-1100/ME Metro Ethernet Managed Switch CLI Reference Guide Power: The power port is where to connect the AC power cord. DGS-1100-18/ME 16-Port 10/100/1000Mpbs + 2 Port SFP 1000 Mbps Switch Front Panel Figure 2-3 - DGS-1100-18/ME Front Panel Power LED: The Power LED lights up when the Switch is connected to a power source. Link/Act/Speed LED (Ports 1-16): Solid Green: When there is a secure 1000Mbps connection at the port.

  • Page 13: Dgs-1100-24/Me

    DGS-1100/ME Metro Ethernet Managed Switch CLI Reference Guide DGS-1100-24/ME 24-Port 10/100/1000Mpbs Switch Front Panel Figure 2-5 – DGS-1100-24/ME Front Panel Power LED: The Power LED lights up when the Switch is connected to a power source. Link/Act/Speed LED (Ports 1-24): Solid Green: When there is a secure 1000Mbps connection at the port.

  • Page 14: Dgs-1100-24P/Me

    DGS-1100/ME Metro Ethernet Managed Switch CLI Reference Guide DGS-1100-24P/ME 12-Port 10/100/1000Mpbs PoE + 12-Port 10/100/1000Mpbs Switch Front Panel Figure 2-7 – DGS-1100-24P/ME Front Panel Power LED: The Power LED lights up when the Switch is connected to a power source. Link/Act/Speed LED (Ports 1-24): Solid Green: When there is a secure 1000Mbps connection at the port.

  • Page 15: Dgs-1100-26/Me

    DGS-1100/ME Metro Ethernet Managed Switch CLI Reference Guide DGS-1100-26/ME 24-Port 10/100/1000Mpbs + 2-Port SFP 1000 Mbps Switch Front Panel Figure 2-9 – DGS-1100-26/ME Front Panel Power LED: The Power LED lights up when the Switch is connected to a power source. Link/Act/Speed LED (Ports 1-24): Solid Green: When there is a secure 1000Mbps connection at the port.

  • Page 16: Hardware Installation

    DGS-1100/ME Metro Ethernet Managed Switch CLI Reference Guide HARDWARE INSTALLATION This chapter provides unpacking and installation information for the D-Link Switch. Step 1: Unpacking Open the shipping carton and carefully unpack its contents. Please consult the packing list located in the User Manual to make sure all items are present and undamaged.

  • Page 17: Rack Installation

    DGS-1100/ME Metro Ethernet Managed Switch CLI Reference Guide Figure 3-1 – Attach the adhesive rubber pads to the bottom Rack Installation The switch can be mounted in an EIA standard size 11-inch rack, which can be placed in a wiring closet with other equipment.

  • Page 18: Step 3 - Plugging In The Ac Power Cord

    DGS-1100/ME Metro Ethernet Managed Switch CLI Reference Guide Step 3 – Plugging in the AC Power Cord Users may now connect the AC power cord into the rear of the switch and to an electrical outlet (preferably one that is grounded and surge protected). Figure 3-4 –...
  • Page 19 DGS-1100/ME Metro Ethernet Managed Switch CLI Reference Guide Figure 3-5 – Ground cable, screw and #8 terminal lug rings...

  • Page 20: Using The Command Line Interface

    DGS-1100/ME Metro Ethernet Managed Switch CLI Reference Guide USING THE COMMAND LINE INTERFACE The Switch allows a computer or terminal to perform some basic monitoring and configuration tasks by using the Command Line Interface (CLI) via TELNET protocol. NOTE: Switch configuration settings are saved to non-volatile RAM using the save command. The current configuration will then be retained in the Switch’s NV-RAM, and reloaded when the Switch is rebooted.
  • Page 21 DGS-1100/ME Metro Ethernet Managed Switch CLI Reference Guide Figure 5–3 Example Command Parameter Help In this case, the command config account was entered with the parameter <username>. The CLI will then prompt to enter the <username> with the message, command: config account. Every command in the CLI has this feature, and complex commands have several layers of parameter prompting.
  • Page 22 DGS-1100/ME Metro Ethernet Managed Switch CLI Reference Guide Figure 5–5 Available Commands The top-level commands consist of commands such as show or config. Most of these commands require one or more parameters to narrow the top-level command. This is equivalent to show what? or config what? Where the what? is the next parameter.

  • Page 23: Command Syntax

    DGS-1100/ME Metro Ethernet Managed Switch CLI Reference Guide COMMAND SYNTAX The following symbols are used to describe how command entries are made and values and arguments are specified in this manual. The online help contained in the CLI and available through the Telnet uses the same syntax.
  • Page 24 DGS-1100/ME Metro Ethernet Managed Switch CLI Reference Guide {braces} Purpose Encloses an optional value or set of optional arguments. Syntax reboot {force_agree} Description In the above syntax example, simply to execute “reboot” to reboot the switch with confirmation. Or, to excute “reboot force_agree” to reboot the switch without confirmation.
  • Page 25 DGS-1100/ME Metro Ethernet Managed Switch CLI Reference Guide Displays the remaining pages without pausing between pages. Enter Displays the next line or table entry.

  • Page 26: Basic Switch Commands

    DGS-1100/ME Metro Ethernet Managed Switch CLI Reference Guide BASIC SWITCH COMMANDS The Basic Switch commands in the Command Line Interface (CLI) are listed (along with the appropriate parameters) in the following table. Command Parameter clear screen create account [admin | user] <username 15> delete account <username 15>...

  • Page 27: Clear Screen

    DGS-1100/ME Metro Ethernet Managed Switch CLI Reference Guide Each command is listed in detail, as follows: clear screen Purpose To clear screen. Syntax clear screen The clear screen command clears the terminal screen. Description Parameters None. Restrictions None. Example usage: To create an administrator-level user account with the username ‘dlink’: DGS-1100-24P/ME:admin#clear screen Command : clear screen...

  • Page 28: Config Account

    DGS-1100/ME Metro Ethernet Managed Switch CLI Reference Guide Syntax delete account <username 15> Description The delete account command deletes an existing user account. Users must delete a user-level account before deleting an admin- level account. Parameters <username 15> − the account username. Restrictions Only administrator-level users can issue this command.

  • Page 29: Show Session

    DGS-1100/ME Metro Ethernet Managed Switch CLI Reference Guide their access levels created on the Switch. Up to 2 user accounts can exist on the Switch at one time. Parameters None. Restrictions None. Example usage: To display the account that has been created: DGS-1100-24P/ME:admin#show account Command : show account Current Accounts:...

  • Page 30: Show Config

    DGS-1100/ME Metro Ethernet Managed Switch CLI Reference Guide Description The show switch command displays information about the Switch settings, including Device Type, MAC Address, IP configuration, Hardware/Software version, System information, and Switch Network configuration. Parameters None. Restrictions None. Example usage: To display the Switch information: DGS-1100-24P/ME:admin#show switch Command: show switch...

  • Page 31: Config Jumbo_Frame

    DGS-1100/ME Metro Ethernet Managed Switch CLI Reference Guide DGS-1100-24P/ME:admin#show config current_config Command : show config current_config DGS-1100-24P/ME Gigabit Ethernet Switch Configuration Firmware: Build 1.00.L001 Copyright(C) 2014 D-Link Corporation. All rights reserved. #BLOCK_UNKNOWN_MULTICAST# disable block_unknown_multicast #MIRROR# disable mirror #MULTICAST FILTER# #VOICE VLAN#...

  • Page 32: Show Jumbo_Frame

    DGS-1100/ME Metro Ethernet Managed Switch CLI Reference Guide Command: config jumbo_frame ports 1-5 state enable Success. DGS-1100-24P/ME:admin# show jumbo_frame Purpose To display the jumbo frame configuration. Syntax show jumbo_frame The show jumbo_frame command displays the jumbo frame Description configuration. Parameters None.

  • Page 33: Save

    DGS-1100/ME Metro Ethernet Managed Switch CLI Reference Guide Disabled Disabled Disabled DGS-1100-24P/ME:admin# save Purpose To save changes in the Switch’s configuration to non-volatile RAM. Syntax save The save command used to enter the current switch configuration Description into non-volatile RAM. The saved switch configuration will be loaded into the Switch’s memory each time the Switch is restarted.

  • Page 34: Reset

    DGS-1100/ME Metro Ethernet Managed Switch CLI Reference Guide reset Purpose To reset the Switch to the factory default settings. Syntax reset [config | system | default] {force_agree} The reset system command restores the Switch’s configuration to Description the factory default settings. Rebooting will clear all entries in the Forwarding Data Base.

  • Page 35: Logout

    DGS-1100/ME Metro Ethernet Managed Switch CLI Reference Guide logout Purpose To log out a user from the Switch. Syntax logout The logout command terminates the current user’s session on the Description Switch. Parameters None. Restrictions None. Example usage: To terminate the current user’s Telnet session: DGS-1100-24P/ME:admin#logout ping Purpose...

  • Page 36: Delete Time_Range

    DGS-1100/ME Metro Ethernet Managed Switch CLI Reference Guide Syntax create time_range <string 8> [daily start_time < time hh:mm > end_time<time hh:mm > | weekly start_weekday <weekday> start_time <time hh:mm > end_weekday <weekday> end_time <time hh:mm> ] Description The create time_range command defines time ranges for access lists.

  • Page 37: Show Time_Range

    DGS-1100/ME Metro Ethernet Managed Switch CLI Reference Guide DGS-1100-24P/ME:admin#delete time_range dlink Command : delete time_range dlink Success. DGS-1100-24P/ME:admin# show time_range Purpose To display the currently configured access profiles on the Switch. Syntax show time_range Description The show time_range command displays the time range configuration.

  • Page 38: Show Telnet

    DGS-1100/ME Metro Ethernet Managed Switch CLI Reference Guide Success DGS-1100-24P/ME:admin# show telnet Purpose To display information about auto-logout time on the Switch. Syntax show telnet The show telnet command displays auto-logout time on the Switch. Description Parameters None. Restrictions None. Example usage: To display the auto-logout time information: DGS-1100-24P/ME:admin#show telnet...

  • Page 39: Create Iproute

    DGS-1100/ME Metro Ethernet Managed Switch CLI Reference Guide Description The show firmware information command is used to display the firmware section information. Parameters information – To display the firmware information. Restrictions None. Example usage: To display firmware information on the Switch: DGS-1100-24P/ME:admin# admin#show firmware information Command : show firmware information Image ID...

  • Page 40: Config Command_Prompt

    DGS-1100/ME Metro Ethernet Managed Switch CLI Reference Guide Description The delete iproute command will delete an existing IP route entry from the Switch’s IP routing table. Parameters default – Specifies to delete a default IP route entry. Restrictions Only administrator-level users can issue this command. Example usage: To delete the default Gateway from the routing table: DGS-1100-24P/ME:admin# delete iproute default...

  • Page 41: Switch Port Commands

    DGS-1100/ME Metro Ethernet Managed Switch CLI Reference Guide SWITCH PORT COMMANDS The Switch Port commands in the Command Line Interface (CLI) are listed (along with the appropriate parameters) in the following table. Command Parameter <portlist> [mdix [normal | cross | auto] | description [add <desc 8> | config ports clear_description] | flow_control [enable | disable] | learning [enable | disable] | state [enable | disable] | speed [auto | 100_full | 100_half | 10_full | 10_half]]...

  • Page 42: Show Ports

    DGS-1100/ME Metro Ethernet Managed Switch CLI Reference Guide Restrictions Only administrator-level users can issue this command. Example usage: To configure the speed of ports 1-3 to be 100 Mbps, full duplex: DGS-1100-24P/ME:admin#config ports 1-3 speed 100_full Command : config ports 1-3 speed 100_full Success.

  • Page 43: Loopback Detection Commands

    DGS-1100/ME Metro Ethernet Managed Switch CLI Reference Guide LOOPBACK DETECTION COMMANDS The Loopback Detection commands in the Command Line Interface (CLI) are listed (along with the appropriate parameters) in the following table. Command Parameter enable loopdetect disable loopdetect { interval_time <value 1-32767> | lbd_recover_time <0, sec 60-1000000> | trap config loopdetect [ none | loop_detected ] | ports[ port_list <portlist>...

  • Page 44: Config Loopdetect

    DGS-1100/ME Metro Ethernet Managed Switch CLI Reference Guide on the Switch. Parameters None. Restrictions Only administrator-level users can issue this command. Example usage: To disable the loopback detection feature on the Switch: DGS-1100-24P/ME:admin#disable loopdetect Command: disable loopdetect Success. DGS-1100-24P/ME:admin# config loopdetect Purpose To configure the loop back settings on the Switch.

  • Page 45: Show Loopdetect

    DGS-1100/ME Metro Ethernet Managed Switch CLI Reference Guide To configure loop back detection with interval time 500 on the Switch: DGS-1100-24P/ME:admin#config loopdetect interval_time 500 Command: config loopdetect interval_time 500 Success. DGS-1100-24P/ME:admin# show loopdetect Purpose To display the loop back detection information on the Switch. show loopdetect [global | ports [portlist <portlist>...

  • Page 46: Network Management (Snmp) Commands

    DGS-1100/ME Metro Ethernet Managed Switch CLI Reference Guide NETWORK MANAGEMENT (SNMP) COMMANDS The Switch supports the Simple Network Management Protocol (SNMP) versions 1 and 2c. Users can specify which version of the SNMP host wants to use to get the trap from the Switch. The following table lists the security features of the three SNMP versions: SNMP Version Authentication Method...

  • Page 47: Create Snmp Community

    DGS-1100/ME Metro Ethernet Managed Switch CLI Reference Guide Command Parameter config snmp [enable | disable] coldstart_traps config snmp [enable | disable] warmstart_traps enable snmp disable snmp show snmp global state Each command is listed in detail, as follows: create snmp community Purpose To create an SNMP community string to define the relationship between the SNMP manager and an SNMP agent.

  • Page 48: Delete Snmp Community

    DGS-1100/ME Metro Ethernet Managed Switch CLI Reference Guide delete snmp community Purpose To remove a specific SNMP community string from the Switch. Syntax delete snmp community <string 16> The delete snmp community command removes a previously Description defined SNMP community string from the Switch. Parameters <string 16>...

  • Page 49: Create Snmp Host

    DGS-1100/ME Metro Ethernet Managed Switch CLI Reference Guide create snmp host Purpose To create a recipient of SNMP traps generated by the Switch’s SNMP agent. create snmp host <ipaddr> [v1 | v2c] <string 16> Syntax Description The create snmp host command creates a recipient of SNMP traps generated by the Switch’s SNMP agent.

  • Page 50: Show Snmp Host

    DGS-1100/ME Metro Ethernet Managed Switch CLI Reference Guide Success. DGS-1100-24P/ME:admin# show snmp host Purpose To display the recipient of SNMP traps generated by the Switch’s SNMP agent. show snmp host Syntax Description The show snmp host command is used to display the IP addresses and configuration information of remote SNMP managers that are designated as recipients of SNMP traps generated by the Switch’s SNMP agent.

  • Page 51: Disable Snmp Traps

    DGS-1100/ME Metro Ethernet Managed Switch CLI Reference Guide Success. DGS-1100-24P/ME:admin# disable snmp traps Purpose To disable SNMP trap support on the Switch. Syntax disable snmp traps The disable snmp traps command disables SNMP trap support on Description the Switch. Parameters None.

  • Page 52: Enable Snmp Authenticate_Traps

    DGS-1100/ME Metro Ethernet Managed Switch CLI Reference Guide DGS-1100-24P/ME:admin# enable snmp authenticate_traps Purpose To enable SNMP authentication trap support. enable snmp authenticate_traps Syntax Description The enable snmp authenticate_traps command enables SNMP authentication trap support on the Switch. Parameters None. Restrictions Only administrator-level users can issue this command.

  • Page 53: Config Snmp System_Name

    DGS-1100/ME Metro Ethernet Managed Switch CLI Reference Guide Description The config snmp system_location command enters a description of the location of the Switch. A maximum of 16 characters can be used. Parameters <string 16> - A maximum of 16 characters are allowed. Restrictions Only administrator-level users can issue this command.

  • Page 54: Config Snmp Linkup_Traps

    DGS-1100/ME Metro Ethernet Managed Switch CLI Reference Guide Example usage: To configure the Switch name as ‘10ME’: DGS-1100-24P/ME:admin#config snmp system_name 10ME Command : config snmp system_name 10ME Success. DGS-1100-24P/ME:admin# config snmp linkup_traps Purpose To configure SNMP link up trap support. Syntax config snmp linkup_traps [enable | disable] The config snmp linkup_traps command configures SNMP link up...

  • Page 55: Config Snmp Coldstart_Traps

    DGS-1100/ME Metro Ethernet Managed Switch CLI Reference Guide DGS-1100-24P/ME:admin# config snmp coldstart_traps Purpose To configure SNMP cold start trap support. config snmp coldstart_traps [enable | disable] Syntax Description The config snmp coldstart_traps command configures SNMP cold start trap support on the Switch. [enable | disable] –...

  • Page 56: Disable Snmp

    DGS-1100/ME Metro Ethernet Managed Switch CLI Reference Guide Parameters None. Restrictions Only administrator-level users can issue this command. Example usage: To enable SNMP support on the Switch: DGS-1100-24P/ME:admin#enable snmp Command : enable snmp Success. DGS-1100-24P/ME:admin# disable snmp Purpose To disable SNMP support. disable snmp Syntax Description...
  • Page 57 DGS-1100/ME Metro Ethernet Managed Switch CLI Reference Guide SNMP State : Disabled SNMP Trap : Disabled DGS-1100-24P/ME:admin#...

  • Page 58: Download/Upload Commands

    DGS-1100/ME Metro Ethernet Managed Switch CLI Reference Guide DOWNLOAD/UPLOAD COMMANDS The Download/Upload commands in the Command Line Interface (CLI) are listed (along with the appropriate parameters) in the following table. Command Parameter { firmware_fromTFTP <ipaddr> <path_filename (64)> image_id <value (1-2)> | download cfg_fromTFTP <ipaddr>...

  • Page 59: Upload

    DGS-1100/ME Metro Ethernet Managed Switch CLI Reference Guide Connecting to Server....Done. Download firmware...... Done. DGS-1100-24P/ME:admin# To download a configuration file: DGS-1100-24P/ME:admin#download cfg_fromTFTP 10.90.90.45 cfg.bin running_cfg Command : download cfg_fromTFTP 10.90.90.45 cfg.bin running_cfg Connecting to Server....Done. Download configuration....Done. DGS-1100-24P/ME:admin# upload Purpose...
  • Page 60 DGS-1100/ME Metro Ethernet Managed Switch CLI Reference Guide Upload firmware......Done. DGS-1100-24P/ME:admin# To upload a configuration file: DGS-1100-24P/ME:admin#upload cfg_toTFTP 10.90.90.45 cfg.bin include_password Command : upload cfg_toTFTP 10.90.90.45 cfg.cfg include_password Connecting to Server....Done. Upload configuration....Done. DGS-1100-24P/ME:admin#...

  • Page 61: Network Monitoring Commands

    DGS-1100/ME Metro Ethernet Managed Switch CLI Reference Guide NETWORK MONITORING COMMANDS The Network Monitoring commands in the Command Line Interface (CLI) are listed (along with the appropriate parameters) in the following table. Command Parameter show packet ports <portlist> show error ports <portlist>...

  • Page 62: Show Error Ports

    DGS-1100/ME Metro Ethernet Managed Switch CLI Reference Guide DGS-1100-24P/ME:admin#show packet ports 5 Command : show packet ports 5 Port Number : 5 Frame Type Total -------------------- ----------- RX Frames 2416 TX Frames 4126 DGS-1100-24P/ME:admin# show error ports Purpose To display the error statistics for a port or a range of ports. Syntax show error ports <portlist>...

  • Page 63: Clear Log

    DGS-1100/ME Metro Ethernet Managed Switch CLI Reference Guide Syntax clear counters {ports <porlist>} Description The clear counters command clears the counters used by the Switch to compile statistics. Parameters <portlist> – Specifies a range of ports to be cleared. Restrictions Only an administrator-level user can issue this command.

  • Page 64: Enable Syslog

    DGS-1100/ME Metro Ethernet Managed Switch CLI Reference Guide Restrictions None. Example usage: To display the Switch history log: DGS-1100-24P/ME:admin#show log index 1-2 Command : show log index 1-2 Index Time Level Description --------- ------------------- ------------- ----------------------------------------- 17:55:34 INFO(6) PORT: Giga eth5 link up 17:55:31 INFO(6) PORT: Giga eth5 link down...

  • Page 65: Show Syslog

    DGS-1100/ME Metro Ethernet Managed Switch CLI Reference Guide Command: disable syslog Success. DGS-1100-24P/ME:admin# show syslog Purpose To display the system log global setting. Syntax show syslog The show syslog command used to display the syslog protocol Description global state. Parameters None.
  • Page 66 DGS-1100/ME Metro Ethernet Managed Switch CLI Reference Guide Notice: normal but significant condition Informational: informational messages all: all-level messages informational − Specifies that informational messages are to be sent to the remote host. This corresponds to number 6 from the list above.

  • Page 67: Show Syslog Host

    DGS-1100/ME Metro Ethernet Managed Switch CLI Reference Guide local1 − Specifies that local use 1 messages are to be sent to the remote host. This corresponds to number 17 from the list above. local2 − Specifies that local use 2 messages are to be sent to the remote host.

  • Page 68: Cable Diagnostic Port

    DGS-1100/ME Metro Ethernet Managed Switch CLI Reference Guide IP Address : 10.90.90.100 Severity : All Facility : Local7 UDP port : 514 Status : Disabled DGS-1100-18/ME:admin# cable diagnostic port Purpose To determine if there are any errors on the copper cables and the position where the errors may have occurred.

  • Page 69: Forwarding Database Commands

    DGS-1100/ME Metro Ethernet Managed Switch CLI Reference Guide FORWARDING DATABASE COMMANDS The Forwarding Database commands in the Command Line Interface (CLI) are listed (along with the appropriate parameters) in the following table. Command Parameter create fdb [name <vlan_name 8> | vlanid <VIDlist 1-4094>] <macaddr> port <port> create multicast_fdb name <vlan_name 8>...

  • Page 70: Create Multicast_Fdb

    DGS-1100/ME Metro Ethernet Managed Switch CLI Reference Guide To create a unicast MAC FDB entry: DGS-1100-24P/ME:admin#create fdb vlanid 1 22-ff-ff-ff-ff-ff port Command : create fdb vlanid 1 22-ff-ff-ff-ff-ff port 2 Success. DGS-1100-24P/ME:admin# create multicast_fdb Purpose To create a static entry in the multicast MAC address forwarding table (database).

  • Page 71: Config Fdb Aging_Time

    DGS-1100/ME Metro Ethernet Managed Switch CLI Reference Guide forwarding table. <portlist> − A port or range of ports to be configured. Restrictions Only administrator-level users can issue this command. Example usage: To configure multicast MAC forwarding: DGS-1100-24P/ME:admin#config multicast_fdb name VLAN0001 ff-ff-ff- ff-ff-ff add 1-8 Command : config multicast_fdb name VLAN0001 ff-ff-ff-ff-ff-ff add 1-8 Success.

  • Page 72: Delete Fdb

    DGS-1100/ME Metro Ethernet Managed Switch CLI Reference Guide delete fdb Purpose To delete an entry in the Switch’s forwarding database. Syntax delete fdb <vlan_name 8> <macaddr> The delete fdb command deletes an entry in the Switch’s MAC Description address forwarding database. Parameters <vlan_name 8>...

  • Page 73: Show Fdb

    DGS-1100/ME Metro Ethernet Managed Switch CLI Reference Guide DGS-1100-24P/ME:admin# show fdb Purpose To display the current unicast MAC address forwarding database. Syntax show fdb {port <port> | vlan <vlan_name 8> | vlanid <vidlist 1- 4094> | mac_address <macaddr> | static | aging_time} Description The show fdb command displays the current contents of the Switch’s forwarding database.

  • Page 74: Config Multicast Filter

    DGS-1100/ME Metro Ethernet Managed Switch CLI Reference Guide config multicast filter Purpose To configure multicast filtering. Syntax config multicast filter [forward | filter] The config multicast filter command enables filtering of multicast Description addresses. Parameters forward - Forwards unregistered multicast packets. filter - Filter unregistered multicast packets.

  • Page 75: Delete Multicast_Fdb

    DGS-1100/ME Metro Ethernet Managed Switch CLI Reference Guide Description The clear fdb command clears FDB entries by ports. Parameters port <port> − The port number. all – Specifies all ports on the Switch. Restrictions Only administrator-level users can issue this command. Example usage: To clear FDB entry of port 2: DGS-1100-24P/ME:admin#clear fdb port 2...

  • Page 76: Broadcast Storm Control Commands

    DGS-1100/ME Metro Ethernet Managed Switch CLI Reference Guide BROADCAST STORM CONTROL COMMANDS The Broadcast Storm Control commands in the Command Line Interface (CLI) are listed (along with the appropriate parameters) in the following table. Command Parameter [ports<portlist> | all] [ broadcast_threshold <value 512-524288>| config traffic control multicast_threshold<value 512-524288>...

  • Page 77: Show Traffic Control

    DGS-1100/ME Metro Ethernet Managed Switch CLI Reference Guide DGS-1100-24P/ME:admin# show traffic control Purpose To display current traffic control settings. show traffic control {ports<portlist>} Syntax Description The show traffic control command displays the current storm traffic control configuration on the Switch. ports <portlist>...

  • Page 78: Qos Commands

    DGS-1100/ME Metro Ethernet Managed Switch CLI Reference Guide QOS COMMANDS The QoS commands in the Command Line Interface (CLI) are listed (along with the appropriate parameters) in the following table. Command Parameter config <portlist>{rx_rate [no_limit | limit <value 8-524288>] | tx_rate [no_limit | limit bandwidth_control <value 64-524288>]}(1) show...

  • Page 79: Show Bandwidth_Control

    DGS-1100/ME Metro Ethernet Managed Switch CLI Reference Guide Example usage: To configure bandwidth control configuration: DGS-1100-24P/ME:admin#config bandwidth_control 7-9 rx_rate limit 128 tx_rate limit 64 Command : config bandwidth_control 8-9 rx_rate limit 128 tx_rate limit 64 Success. DGS-1100-24P/ME:admin# show bandwidth_control Purpose To display bandwidth control settings on the Switch.

  • Page 80: Show 802.1P User_Priority

    DGS-1100/ME Metro Ethernet Managed Switch CLI Reference Guide eth20 No Limit No Limit eth21 No Limit No Limit eth22 No Limit No Limit eth23 No Limit No Limit eth24 No Limit No Limit Total Entries: 24 DGS-1100-24P/ME:admin# show 802.1p user_priority Purpose To display the 802.1p user priority.

  • Page 81: Show Scheduling_Mechanism

    DGS-1100/ME Metro Ethernet Managed Switch CLI Reference Guide The Switch’s default is to empty the four hardware priority queues in order − from the highest priority hardware queue (class 3) to the lowest priority hardware queue (class 0). Each queue will transmit all of the packets in its buffer before allowing the next lower priority queue to transmit its packets.

  • Page 82: Config 802.1P Default_Priority

    DGS-1100/ME Metro Ethernet Managed Switch CLI Reference Guide eth10 Total Entries: 1 DGS-1100-24P/ME:admin# config 802.1p default_priority Purpose To specify default priority handling of untagged packets received by the Switch. Syntax config scheduling {ports <portlist>} [ Low | Medium | High | Highest] Description The configure 802.1p default_priority command allows you to...
  • Page 83 DGS-1100/ME Metro Ethernet Managed Switch CLI Reference Guide Command : show 802.1p default_priority ports 1-4 Port Default CoS ------------ ------------------ eth1 Medium eth2 Medium eth3 eth4 Total Entries: 4 DGS-1100-24P/ME:admin#...

  • Page 84: Port Mirroring Commands

    DGS-1100/ME Metro Ethernet Managed Switch CLI Reference Guide PORT MIRRORING COMMANDS The Port Mirroring commands in the Command Line Interface (CLI) are listed (along with the appropriate parameters) in the following table. Command Parameter enable mirror disable mirror config mirror target <port>...

  • Page 85: Config Mirror

    DGS-1100/ME Metro Ethernet Managed Switch CLI Reference Guide off without having to modify the port mirroring configuration. Parameters None. Restrictions Only administrator-level users can issue this command. Example usage: To disable mirroring configurations: DGS-1100-24P/ME:admin#disable mirror Command : disable mirror Success. DGS-1100-24P/ME:admin# config mirror Purpose...

  • Page 86: Show Mirror

    DGS-1100/ME Metro Ethernet Managed Switch CLI Reference Guide DGS-1100-24P/ME:admin# show mirror Purpose To show the current port mirroring configuration on the Switch. show mirror Syntax Description The show mirror command displays the current port mirroring configuration on the Switch. Parameters None.

  • Page 87: Vlan Commands

    DGS-1100/ME Metro Ethernet Managed Switch CLI Reference Guide VLAN COMMANDS The VLAN commands in the Command Line Interface (CLI) are listed (along with the appropriate parameters) in the following table. Command Parameter create vlan [name <vlan_name 8> tag<vlanid 2-4094> | vlanid <vidlist 2-4094>] delete vlan [name <vlan_name 8>...

  • Page 88: Delete Vlan

    DGS-1100/ME Metro Ethernet Managed Switch CLI Reference Guide Description The create vlan command creates a VLAN on the Switch. Parameters name <vlan_name 8> − The name of the VLAN to be created. Each VLAN name can be up to 8 characters. tag <vlanid 2-4094>...

  • Page 89: Show Vlan

    DGS-1100/ME Metro Ethernet Managed Switch CLI Reference Guide Description The config vlan command allows the user to add or delete ports to the port list of a previously configured VLAN. You can specify the additional ports as tagging, untagging, or forbidden. The default is to assign the ports as untagged.

  • Page 90: Enable Asymmetric_Vlan

    DGS-1100/ME Metro Ethernet Managed Switch CLI Reference Guide VLAN Name : VLAN0001 member Ports : 1-24 Current Tagged Ports : 1-3 Current Untagged Ports : 4-24 Static Tagged Ports : 1-3 Static Untagged Ports : 4-24 VLAN Name member Ports Current Tagged Ports Current Untagged Ports : Static Tagged Ports...

  • Page 91: Show Asymmetric_Vlan

    DGS-1100/ME Metro Ethernet Managed Switch CLI Reference Guide Parameters None. Restrictions Only administrator-level users can issue this command. Example usage: To disable asymmetric_vlan on the switch: DGS-1100-24P/ME:admin#disable asymmetric_vlan Command: disable asymmetric_vlan Success. DGS-1100-24P/ME:admin# show asymmetric_vlan Purpose To display the asymmetric VLAN status on the Switch. show asymmetric_vlan Syntax Description...

  • Page 92: Disable Management_Vlan

    DGS-1100/ME Metro Ethernet Managed Switch CLI Reference Guide Success. DGS-1100-24P/ME:admin# disable management_vlan Purpose To disable the management VLAN on the Switch. Syntax disable management_vlan disable management_vlan command disables Description management VLAN on the Switch. Parameters None. Restrictions Only administrator-level users can issue this command. Example usage: To disable management VLAN on the switch: DGS-1100-24P/ME:admin#disable management_vlan...

  • Page 93: Show Management_Vlan

    DGS-1100/ME Metro Ethernet Managed Switch CLI Reference Guide show management_vlan Purpose To display the management VLAN on the Switch. Syntax show management_vlan The show management_vlan command displays the management Description VLAN information on the Switch. Parameters None. Restrictions None. Example usage: To display the management VLAN on the switch: DGS-1100-24P/ME:admin#show management_vlan Command: show management_vlan...

  • Page 94: Show Port_Vlan

    DGS-1100/ME Metro Ethernet Managed Switch CLI Reference Guide show port_vlan Purpose To display the port PVID of VLAN on the Switch. Syntax show port_vlan {port <portlist>} The show port_vlan command displays the port PVID of VLAN on Description the Switch. Parameters None.

  • Page 95: Disable Pvid Auto_Assign

    DGS-1100/ME Metro Ethernet Managed Switch CLI Reference Guide Success. DGS-1100-24P/ME:admin# disable pvid auto_assign Purpose To disable PVID auto assign of port vlan. Syntax disable pvid auto_assign Description To disable PVID auto assign. Parameters None. Restrictions Only administrator-level users can issue this command. Example usage: To disable PVID auto_assign: DGS-1100-24P/ME:admin#disable pvid auto_assign...

  • Page 96: Basic Ip Commands

    DGS-1100/ME Metro Ethernet Managed Switch CLI Reference Guide BASIC IP COMMANDS The Basic IP commands in the Command Line Interface (CLI) are listed (along with the appropriate parameters) in the following table. Command Parameter [dhcp {retry_time <retry_time 5-120>} |ipaddress <network_address> | bootp | ipv6 config ipif system {state [enable|disable] | ipv6address <ip_address>}(1)] show ipif...

  • Page 97: Show Ipif

    DGS-1100/ME Metro Ethernet Managed Switch CLI Reference Guide show ipif Purpose To display the configuration of an IP interface on the Switch. Syntax show ipif The show ipif command displays the configuration of an IP interface Description on the Switch. Parameters None.

  • Page 98: Igmp Snooping Commands

    DGS-1100/ME Metro Ethernet Managed Switch CLI Reference Guide IGMP SNOOPING COMMANDS The Switch supports IGMPv1-, IGMPv2-, and IGMPv3 awareness (excluded IGMPv3 source-filtering) snooping. The IGMP Snooping commands in the Command Line Interface (CLI) are listed (along with the appropriate parameters) in the following table. Command Parameter enable igmp_snooping...

  • Page 99: Enable Igmp_Snooping

    DGS-1100/ME Metro Ethernet Managed Switch CLI Reference Guide Command Parameter show igmp_snooping [all | [vlan_name <vlan_name 8> | vlanid <vidlist 1-4094>]<ipaddr>] static_group Each command is listed in detail, as follows: enable igmp_snooping Purpose To enable IGMP snooping on the Switch. Syntax enable igmp_snooping The enable igmp_snooping command enables IGMP snooping on...

  • Page 100: Show Igmp_Snooping

    DGS-1100/ME Metro Ethernet Managed Switch CLI Reference Guide DGS-1100-24P/ME:admin# show igmp_snooping Purpose To display IGMP snooping on the Switch. Syntax show igmp_snooping [vlan_name <vlan_name 8> | vlanid<vidlist 1-4094> | all] Description The show igmp_snooping command displays IGMP snooping on the Switch. Parameters vlan_name <vlan_name 8>...

  • Page 101: Config Igmp_Snooping Querier

    DGS-1100/ME Metro Ethernet Managed Switch CLI Reference Guide Description The config igmp_snooping command configures IGMP snooping on the Switch. Parameters vlan_name <vlan_name 8> − The name of the VLAN for which IGMP snooping is to be configured. vlanid <vidlist 1-4094> − The VLAN ids for which IGMP snooping is to be configured.

  • Page 102: Create Igmp_Snooping Static_Group

    DGS-1100/ME Metro Ethernet Managed Switch CLI Reference Guide DGS-1100-24P/ME:admin# create igmp_snooping static_group Purpose To create an IGMP snooping static group on the Switch. Syntax create igmp_snooping static_group [vlan_name<vlan_name 8> | vlanid < vidlist 1-4094> ] <ipaddr> Description The create igmp_snooping static_group command creates an IGMP snooping static group on the Switch.

  • Page 103: Config Igmp_Snooping Static_Group

    DGS-1100/ME Metro Ethernet Managed Switch CLI Reference Guide config igmp_snooping static_group Purpose To configure an IGMP snooping static group on the Switch. Syntax config igmp_snooping static_group [vlan_name <vlan_name 8> | vlanid < vidlist 1-4094> ] < ipaddr > [ add | delete] <portlist> Description The config igmp_snooping static_group command is used to add or delete static member ports from a static group on the Switch.

  • Page 104: Create Igmp_Snooping Multicast_Vlan

    DGS-1100/ME Metro Ethernet Managed Switch CLI Reference Guide static group is to be deleted. The range is from 1 to 4094. <ipaddr> − The multicast group IP address. Restrictions Only administrator-level users can issue this command. Example usage: To delete the igmp snooping static group: DGS-1100-24P/ME:admin#delete igmp_snooping static_group vlanid 1 225.0.0.1 Command : delete igmp_snooping static_group vlanid 1 225.0.0.1...

  • Page 105: Delete Igmp_Snooping Multicast_Vlan

    DGS-1100/ME Metro Ethernet Managed Switch CLI Reference Guide Parameters <vlan_name 8> − The name of the VLAN for which IGMP snooping is to be configured. Up to 8 characters can be used. action [add | delete] − Specify whether to add or delete ports defined in the following parameter member ports, source ports or tag member ports to the multicast VLAN.

  • Page 106: Config Igmp_Snooping Multicast_Vlan_Group

    DGS-1100/ME Metro Ethernet Managed Switch CLI Reference Guide DGS-1100-24P/ME:admin# config igmp_snooping multicast_vlan_group Purpose To specify that IGMP snooping is to be configured for multicast vlan groups on the Switch. Syntax config igmp_snooping multicast_vlan_group <vlan_name 8> [add | delete] ipv4_range <mcast_address_range> The config igmp_snooping multicast_vlan_group command Description specifies an IGMP snooping multicast VLAN group on the Switch.

  • Page 107: Disable Igmp_Snooping Multicast_Vlan

    DGS-1100/ME Metro Ethernet Managed Switch CLI Reference Guide Success. DGS-1100-24P/ME:admin# disable igmp_snooping multicast_vlan Purpose To disable IGMP snooping multicast VLAN on the Switch. Syntax disable igmp_snooping multicast_vlan The disable igmp_snooping multicast_vlan command disables Description IGMP snooping multicast VLAN on the Switch. Parameters None.

  • Page 108: Show Igmp_Snooping Multicast_Vlan_Group

    DGS-1100/ME Metro Ethernet Managed Switch CLI Reference Guide Member(Untagged) Ports : 10-12 Tagged Member Ports Source Ports Status : Disabled Replace Source IP : 0.0.0.0 Total Entries: 1 DGS-1100-24P/ME:admin# show igmp_snooping multicast_vlan_group Purpose To show the current status of IGMP snooping multicast VLAN group on the Switch.

  • Page 109: Show Igmp_Snooping Static_Group

    DGS-1100/ME Metro Ethernet Managed Switch CLI Reference Guide groups). Parameters all – Display all the IGMP snooping group enties. vlan_name <vlan_name 8> − The name of the VLAN that IGMP snooping group configuration information will to be displayed on. Up to 8 characters can be used.
  • Page 110 DGS-1100/ME Metro Ethernet Managed Switch CLI Reference Guide -------------------- ---------------- ------------------------ 1 /VLAN0001 225.0.0.1 Total Entries: 1 DGS-1100-24P/ME:admin#...

  • Page 111: Mld Snooping Commands

    DGS-1100/ME Metro Ethernet Managed Switch CLI Reference Guide MLD SNOOPING COMMANDS The Switch supports MLDv1- and MLDv2 awareness (excluded MLDv2 source-filtering) snooping. The MLD Snooping commands in the Command Line Interface (CLI) are listed (along with the appropriate parameters) in the following table. Command Parameter enable mld_snooping...

  • Page 112: Enable Mld_Snooping

    DGS-1100/ME Metro Ethernet Managed Switch CLI Reference Guide Command Parameter static_group Each command is listed in detail, as follows: enable mld_snooping Purpose To enable MLD snooping on the Switch. enable mld snooping Syntax Description The enable mld snooping command enables MLD snooping on the Switch.

  • Page 113: Config Mld_Snooping

    DGS-1100/ME Metro Ethernet Managed Switch CLI Reference Guide config mld_snooping Purpose To configure mld snooping. Syntax config mld_snooping [vlan_name <vlan_name 8> | vlanid <vidlist 1-4094> | all] {fast_leave [enable | disable] | state [enable | disable]}(1) Description The config mld_snooping command defines mld snooping on the VLAN.

  • Page 114: Create Mld_Snooping Static_Group

    DGS-1100/ME Metro Ethernet Managed Switch CLI Reference Guide Example usage: To configure MLD snooping querier: DGS-1100-24P/ME:admin#config mld_snooping querier vlanid 1 state enable Command : config mld_snooping querier vlanid 1 state enable Success. DGS-1100-24P/ME:admin# create mld_snooping static_group Purpose To create an MLD snooping static group on the Switch. Syntax create mld_snooping static_group [vlan_name<vlan_name 8>...

  • Page 115: Config Mld_Snooping Static_Group

    DGS-1100/ME Metro Ethernet Managed Switch CLI Reference Guide DGS-1100-24P/ME:admin# config mld_snooping static_group Purpose To configure an MLD snooping static group on the Switch. config mld_snooping static_group [vlan_name <vlan_name 8> Syntax | vlanid < vidlist 1-4094> ] < ipv6addr > [ add | delete] <portlist> Description The config mld_snooping static_group command is used to add or delete static member ports in a static group on the Switch.

  • Page 116: Create Mld_Snooping Multicast_Vlan

    DGS-1100/ME Metro Ethernet Managed Switch CLI Reference Guide vlanid <1-4094> − The ID of the VLAN on which the MLD snooping static group will be deleted. The range is from 1 to 4094. <ipv6addr> − The multicast group IPv6 address. Restrictions Only administrator-level users can issue this command.

  • Page 117: Delete Mld_Snooping Multicast_Vlan

    DGS-1100/ME Metro Ethernet Managed Switch CLI Reference Guide Parameters <vlan_name 8> − The name of the VLAN for which MLD snooping is to be configured. Up to 8 characters can be used. action [add | delete] − Specify whether to add or delete ports defined in the following parameter member ports, source ports or tag member ports to the multicast VLAN.

  • Page 118: Config Mld_Snooping Multicast_Vlan_Group

    DGS-1100/ME Metro Ethernet Managed Switch CLI Reference Guide DGS-1100-24P/ME:admin# config mld_snooping multicast_vlan_group Purpose To specify that MLD snooping is to be configured for multicast vlan groups on the Switch. Syntax config mld_snooping multicast_vlan_group <vlan_name 8> [add | delete] ipv6_range <mcast_range 80> The config mld_snooping multicast_vlan_group command Description...

  • Page 119: Disable Mld_Snooping Multicast_Vlan

    DGS-1100/ME Metro Ethernet Managed Switch CLI Reference Guide Success. DGS-1100-24P/ME:admin# disable mld_snooping multicast_vlan Purpose To disable MLD snooping multicast VLAN on the Switch. Syntax disable mld_snooping multicast_vlan The disable mld_snooping multicast_vlan command disables Description MLD snooping multicast VLAN on the Switch. Parameters None.

  • Page 120: Show Mld_Snooping Multicast_Vlan_Group

    DGS-1100/ME Metro Ethernet Managed Switch CLI Reference Guide Tagged Member Ports Source Ports Status : Disabled Replace Source IP : :: Total Entries: 1 DGS-1100-24P/ME:admin# show mld_snooping multicast_vlan_group Purpose To show the current status of MLD snooping multicast VLAN group on the Switch.

  • Page 121: Show Mld_Snooping Group

    DGS-1100/ME Metro Ethernet Managed Switch CLI Reference Guide Restrictions None. Example usage: To display MLD snooping on the Switch: DGS-1100-24P/ME:admin#show mld_snooping vlan_name VLAN0001 Command : show mld_snooping vlan_name VLAN0001 MLD Snooping Global State : Disabled VLAN Name : VLAN0001 Query Interval : 125 Max Response Time : 10...

  • Page 122: Show Mld_Snooping Static_Group

    DGS-1100/ME Metro Ethernet Managed Switch CLI Reference Guide ipaddress<ipv6addr> − Specifies the MLD Snooping group IPv6 address to be displayed. Restrictions None. Example usage: To show mld snooping group: DGS-1100-24P/ME:admin#show mld_snooping group all Command : show mld_snooping group all Total Entries: 0 DGS-1100-24P/ME:admin# show mld_snooping static_group Purpose...

  • Page 123: Time And Sntp Commands

    DGS-1100/ME Metro Ethernet Managed Switch CLI Reference Guide TIME AND SNTP COMMANDS The Time and SNTP commands in the Command Line Interface (CLI) are listed (along with the appropriate parameters) in the following table. Command Parameter config sntp {ipaddress<ipaddr> | poll_interval <sec 30-99999>}(1) show sntp enable sntp disable sntp...

  • Page 124: Show Sntp

    DGS-1100/ME Metro Ethernet Managed Switch CLI Reference Guide Example usage: To configure SNTP settings: DGS-1100-24P/ME:admin#config sntp ipaddress 10.1.1.1 poll_interval 60 Command : config sntp ipaddress 10.1.1.1 poll_interval 60 Success. DGS-1100-24P/ME:admin# show sntp Purpose To display the SNTP information. Syntax show sntp Description The show sntp command displays SNTP settings information, including the source IP address, time source and poll interval.

  • Page 125: Enable Sntp

    DGS-1100/ME Metro Ethernet Managed Switch CLI Reference Guide enable sntp Purpose To enable SNTP server support. Syntax enable sntp The enable sntp command enables SNTP server support. SNTP Description service must be separately configured (see config sntp). Enabling and configuring SNTP support will override any manually configured system time settings.

  • Page 126: Config Time

    DGS-1100/ME Metro Ethernet Managed Switch CLI Reference Guide config time Purpose To manually configure system time and date settings. Syntax config time <date ddmthyyyy> <time hh:mm:ss> The config time date command configures the system time and Description date settings. These will be overridden if SNTP is configured and enabled.

  • Page 127: Config Dst

    DGS-1100/ME Metro Ethernet Managed Switch CLI Reference Guide Example usage: To configure time zone settings: DGS-1100-24P/ME:admin#config time_zone operator + hour 2 minute 30 Command : config time_zone operator + hour 2 minute 30 Success. DGS-1100-24P/ME:admin# config dst Purpose To configure time adjustments to allow for the use of Daylight Saving Time (DST).

  • Page 128: Show Time

    DGS-1100/ME Metro Ethernet Managed Switch CLI Reference Guide Example usage: To configure daylight savings time on the Switch to run from the 2 April at 3 PM until the 2 October at 3:30 PM and add 30 minutes at the onset of DST: DGS-1100-24P/ME:admin#config dst annual s_date 2 s_mth 4 s_time 15:00 e_date 2 e_mth 10 e_time 15:30 offset 30 Command : config dst annual s_date 2 s_mth 4 s_time 15:00 e_date 2 e_mth...

  • Page 129: Power Saving Commands

    DGS-1100/ME Metro Ethernet Managed Switch CLI Reference Guide POWER SAVING COMMANDS The Power Saving commands in the Command Line Interface (CLI) are listed (along with the appropriate parameters) in the following table. Command Parameter [ [link_detection_scheduled | port_shutdown_scheduled | hiberantion_scheduled | config power_saving global [enable | disable] | time_profile dim-led_scheduled | administrative_dim-led ]...

  • Page 130: Config Power_Saving Port

    DGS-1100/ME Metro Ethernet Managed Switch CLI Reference Guide Example usage: To configure the power saving mode on the switch: DGS-1100-24:admin#config power_saving global link_detection_scheduled enable Command: config power_saving global link_detection_scheduled enable Success. DGS-1100-24:admin# config power_saving port Purpose To configure the power saving on the switch. Syntax config power_saving port [port_list <portlist>| all ] [ time_range <range_name 8>...
  • Page 131 DGS-1100/ME Metro Ethernet Managed Switch CLI Reference Guide To display power saving information on the switch: DGS-1100-24:admin# show power_saving global Command: show power_saving global Link Detection State : Disabled Scheduled Port-shutdown Power Saving : Disabled Scheduled Hibernation Power Saving : Disabled Scheduled Dim-LED Power Saving : Disabled Administrative Dim-LED...

  • Page 132: Lldp Commands

    DGS-1100/ME Metro Ethernet Managed Switch CLI Reference Guide LLDP COMMANDS The LLDP commands in the Command Line Interface (CLI) are listed (along with the appropriate parameters) in the following table. Command Parameter enable lldp disable lldp show lldp show lldp remote_ports config lldp notification [enable | disable] Each command is listed in detail, as follows:...

  • Page 133: Show Lldp

    DGS-1100/ME Metro Ethernet Managed Switch CLI Reference Guide Restrictions Only administrator-level users can issue this command. Example usage: To disable LLDP on the switch: DGS-1100-24P/ME:admin#disable lldp Command: disable lldp Success. DGS-1100-24P/ME:admin# show lldp Purpose To display the Link Layer Discovery Protocol (LLDP) on the switch. Syntax show lldp The show lldp displays the LLDP configuration on the switch.

  • Page 134: Config Lldp

    DGS-1100/ME Metro Ethernet Managed Switch CLI Reference Guide DGS-1100-24P/ME:admin#show lldp remote_ports Command : show lldp remote_ports Remote Entities Count : 1 Entity 1 Chassis Id Subtype : 4 Chassis Id : ec22804008df Port Id Subtype Port Id : eth07 Port Description DGS-1100-24P/ME:admin# config lldp Purpose...

  • Page 135: Traffic Segmentation Commands

    DGS-1100/ME Metro Ethernet Managed Switch CLI Reference Guide TRAFFIC SEGMENTATION COMMANDS The Traffic Segmentation commands in the Command Line Interface (CLI) are listed (along with the appropriate parameters) in the following table. Command Parameter config <portlist> forward_list [all | ports <portlist>] traffic_segmentation show {ports <portlist>}...
  • Page 136 DGS-1100/ME Metro Ethernet Managed Switch CLI Reference Guide Syntax show traffic_segmentation {ports <portlist>} Description The show traffic_segmentation command displays the current traffic segmentation configuration on the Switch. Parameters ports <portlist> – A port or a port channel for which the current traffic segmentation configuration on the Switch will be displayed.

  • Page 137: Safeguard Commands

    DGS-1100/ME Metro Ethernet Managed Switch CLI Reference Guide SAFEGUARD COMMANDS The Safeguard commands in the Command Line Interface (CLI) are listed (along with the appropriate parameters) in the following table. Command Parameter config state [enable | disable] safeguard_engine show safeguard_engine Each command is listed in detail, as follows: config safeguard_engine Purpose...
  • Page 138 DGS-1100/ME Metro Ethernet Managed Switch CLI Reference Guide Example usage: To show the safeguard engine status on the switch: DGS-1100-24P/ME:admin#show safeguard_engine Command: show safeguard_engine Safeguard Engine State : Enabled DGS-1100-24P/ME:admin#...

  • Page 139: Spanning Tree Protocol Commands

    DGS-1100/ME Metro Ethernet Managed Switch CLI Reference Guide SPANNING TREE PROTOCOL COMMANDS The Spanning Tree Protocol commands in the Command Line Interface (CLI) are listed (along with the appropriate parameters) in the following table. Command Parameter config stp ports <portlist> edge [true | false | auto] show stp ports {portlist <portlist>} config stp trap...

  • Page 140: Show Stp Ports

    DGS-1100/ME Metro Ethernet Managed Switch CLI Reference Guide Example usage: To configure STP ports settings DGS-1100-24P/ME:admin#config stp ports 5-10 edge true Command : config stp ports 5-10 edge true Success. DGS-1100-24P/ME:admin# show stp ports Purpose To display the edge state of each port. Syntax show stp ports {portlist <portlist>} The show stp ports command displays the edge mode of each...

  • Page 141: Config Stp Version

    DGS-1100/ME Metro Ethernet Managed Switch CLI Reference Guide Example usage: To configure STP trap settings DGS-1100-24P/ME:admin#config stp trap new_root enable Command : config stp trap new_root enable Success. DGS-1100-24P/ME:admin# config stp version Purpose To set the STP version used by the switch. Syntax config stp version [rstp | stp] The config stp version command sets the STP version used by the...

  • Page 142: Disable Stp

    DGS-1100/ME Metro Ethernet Managed Switch CLI Reference Guide Example usage: To enable STP support DGS-1100-24P/ME:admin#enable stp Command : enable stp Success. DGS-1100-24P/ME:admin# disable stp Purpose To enable STP support of the switch. Syntax disable stp The disable stp command enables STP support of the switch. Description Parameters None.
  • Page 143 DGS-1100/ME Metro Ethernet Managed Switch CLI Reference Guide Example usage: To display STP settings DGS-1100-24P/ME:admin#show stp Command : show stp STP Bridge Global Settings --------------------------- STP Status : Disabled STP Version : RSTP New Root Trap : Enabled Topology Change Trap : Disabled Root Bridge Information --------------------------- Root Bridge...

  • Page 144: Zone Defense Commands

    DGS-1100/ME Metro Ethernet Managed Switch CLI Reference Guide ZONE DEFENSE COMMANDS The Zone Defense commands in the Command Line Interface (CLI) are listed (along with the appropriate parameters) in the following table. Command Parameter enable zone_defense disable zone_defense show zone_defense Each command is listed in detail, as follows: enable zone_defense Purpose...

  • Page 145: Show Zone_Defense

    DGS-1100/ME Metro Ethernet Managed Switch CLI Reference Guide Example usage: To disable zone defense support DGS-1100-24P/ME:admin#disable zone_defense Command : disable zone_defense Success. DGS-1100-24P/ME:admin# show zone_defense Purpose To display zone defense setting of the switch. Syntax disable zone_defense The disable zone_defense command displays zone defense setting Description of the switch.

  • Page 146: D-Link Discovery Protocol Commands

    DGS-1100/ME Metro Ethernet Managed Switch CLI Reference Guide D-LINK DISCOVERY PROTOCOL COMMANDS The D-link Discovery Protocol (DDP) commands in the Command Line Interface (CLI) are listed (along with the appropriate parameters) in the following table. Command Parameter enable ddp disable ddp...

  • Page 147: Config Ddp Report_Time

    DGS-1100/ME Metro Ethernet Managed Switch CLI Reference Guide Example usage: To disable DDP support DGS-1100-24P/ME:admin#disable ddp Command : disable ddp Success. DGS-1100-24P/ME:admin# config ddp report_time Purpose To set the interval between two consecutive DDP report messages. Syntax config ddp report_time [30 | 60 | 90 | 120 | never] The config ddp report_time command configures report period of Description the switch.
  • Page 148 DGS-1100/ME Metro Ethernet Managed Switch CLI Reference Guide Example usage: To display DDP settings DGS-1100-24P/ME:admin#show ddp Command : show ddp DDP status : Enabled DDP report timer : 60 DGS-1100-24P/ME:admin#...

  • Page 149: Poe Commands

    DGS-1100/ME Metro Ethernet Managed Switch CLI Reference Guide POE COMMANDS The PoE commands in the Command Line Interface (CLI) are listed (along with the appropriate parameters) in the following table. Command Parameter config poe system trap_state [enable | disable] [all | portlist <portlist>]{ state [enable | disable] | time_range [ name <range_name 8> config poe ports | clear] | priority [critical | high | low] | power_limit [ auto | class_1| class_2 | class_3| class_4| user_define <value m - n>]}(1)

  • Page 150: Config Poe Ports

    DGS-1100/ME Metro Ethernet Managed Switch CLI Reference Guide config poe ports Purpose To configure PoE system-wise function and port settings. Syntax config poe ports [all | portlist <portlist>] { state [enable | disable] | time_range [ name <range_name 8> | clear] | priority [critical | high | low] | power_limit [ auto | class_1| class_2 | class_3| class_4| user_define <value m - n>]}(1) Description...

  • Page 151: Show Poe System

    DGS-1100/ME Metro Ethernet Managed Switch CLI Reference Guide Example usage: To configure the PoE port: DGS-1100-24P/ME:admin#config poe ports portlist 1-4 state enable priority high Command : config poe ports portlist 1-4 state enable priority high Success. DGS-1100-24P/ME:admin# show poe system Purpose This command is used to display the settings and actual values of the whole PoE system.
  • Page 152 DGS-1100/ME Metro Ethernet Managed Switch CLI Reference Guide Example usage: To show PoE port information: DGS-1100-24P/ME:admin#show poe ports port_list 2-4 Command : show poe ports port_list 2-4 Port Status Class Max (W) Used (W) State Priority Power Limit Time Profile ====================================================== Searching Auto Disabled...

  • Page 153: Surveillance Vlan Commands

    DGS-1100/ME Metro Ethernet Managed Switch CLI Reference Guide SURVEILLANCE VLAN COMMANDS The surveillance vlan commands in the Command Line Interface (CLI) are listed (along with the appropriate parameters) in the following table. Command Parameter enable [ name <vlan_name 8> | vlanid <vlanid 1-4094>] surveillance_vlan disable surveillance_vlan...

  • Page 154: Disable Surveillance_Vlan

    DGS-1100/ME Metro Ethernet Managed Switch CLI Reference Guide Example usage: To enable surveillance vlan with vlanid 3: DGS-1100-24P/ME:admin#enable surveillance_vlan vlanid 3 Command : enable surveillance_vlan vlanid 3 Success. DGS-1100-24P/ME:admin# disable surveillance_vlan Purpose Disables the global Surveillance VLAN function. Syntax disable surveillance_vlan Description To disable the Surveillance VLAN function on a switch.

  • Page 155: Config Surveillance_Vlan Aging_Time

    DGS-1100/ME Metro Ethernet Managed Switch CLI Reference Guide Example usage: To set the surveillance priority 5: DGS-1100-24P/ME:admin#config surveillance_vlan priority 5 Command : config surveillance_vlan priority 5 Success. DGS-1100-24P/ME:admin# config surveillance_vlan aging_time Purpose Configures Surveillance VLAN aging time. Syntax config surveillance_vlan aging_time <min 1-65535> Description To set the aging time of the Surveillance VLAN.

  • Page 156: Config Surveillance_Vlan Oui

    OUI. The user can further define user-defined OUI if needed. A user- defined OUI cannot be the same as any of the pre-defined OUI. The following are the pre-defined surveillance traffic’s OUI: Vendor Mnemonic name F0:7D:68:0x:xx:xx D-Link D-Link IP camera 28:10:7B:00:00:00 D-Link Network camera, Video server, NVR 28:10:7B:2F:FF:FF B0:C5:54:00:00:00~ D-Link...

  • Page 157: Show Surveillance_Vlan Global

    DGS-1100/ME Metro Ethernet Managed Switch CLI Reference Guide show surveillance_vlan global Purpose Shows the Surveillance VLAN global information Syntax show surveillance_vlan global Description This command is used to show the Surveillance VLAN information. Parameters None. Restrictions None. Example usage: To show surveillance vlan global information: DGS-1100-24P/ME:admin#show surveillance_vlan global Command : show surveillance_vlan global Surveillance VLAN State : Disabled...

  • Page 158: Show Surveillance_Vlan Device

    DGS-1100-24P/ME:admin#show surveillance_vlan oui Command : show surveillance_vlan oui OUI Address Mask Component Type Description -------------------------- --------------------- ------------------------------ ----------- 28-10-7b-00-00-00 ff-ff-ff-f0-00-00 D-Link Device ***DD*** 28-10-7b-10-00-00 ff-ff-ff-f0-00-00 D-Link Device ***DD*** 28-10-7b-20-00-00 ff-ff-ff-f0-00-00 D-Link Device ***DD*** b0-c5-54-00-00-00 ff-ff-ff-f0-00-00 D-Link Device ***DD*** b0-c5-54-10-00-00 ff-ff-ff-f0-00-00 D-Link Device...
  • Page 159 DGS-1100/ME Metro Ethernet Managed Switch CLI Reference Guide Example usage: To show surveillance vlan device information: DGS-1100-24P/ME:admin#show surveillance_vlan device all Command: show surveillance_vlan device all Ports Device Address Component Type Start Time -------- ------------------------------ --------------------------------------------- ----------------- -------- C0-A0-BB-75-33-EB Other IP Surveillance Device 1/1/2000 00:01:01 DGS-1100-24P/ME:admin#...

  • Page 160: Voice Vlan Commands

    DGS-1100/ME Metro Ethernet Managed Switch CLI Reference Guide VOICE VLAN COMMANDS The voice vlan commands in the Command Line Interface (CLI) are listed (along with the appropriate parameters) in the following table. Command Parameter enable voice_vlan [ name <vlan_name 8> | vlanid <vlanid 1-4094>] disable voice_vlan config voice_vlan <0-7>...

  • Page 161: Disable Voice_Vlan

    DGS-1100/ME Metro Ethernet Managed Switch CLI Reference Guide Example usage: To enable voice vlan with vlanid 3: DGS-1100-24P/ME:admin#enable voice_vlan vlanid 3 Command : enable voice_vlan vlanid 3 Success. DGS-1100-24P/ME:admin# disable voice_vlan Purpose Disables the global Voice VLAN function. Syntax disable voice_vlan Description To disable the Voice VLAN function on a switch.

  • Page 162: Config Voice_Vlan Aging_Time

    DGS-1100/ME Metro Ethernet Managed Switch CLI Reference Guide Example usage: To set the surveillance priority 5: DGS-1100-24P/ME:admin#config voice_vlan priority 5 Command : config voice_vlan priority 5 Success. DGS-1100-24P/ME:admin# config voice_vlan aging_time Purpose Configures Voice VLAN aging time. Syntax config voice_vlan aging_time <min 1-65535> Description To set the aging time of the Voice VLAN.

  • Page 163: Config Voice_Vlan Oui

    DGS-1100/ME Metro Ethernet Managed Switch CLI Reference Guide config voice_vlan oui Purpose Configures the user-defined OUI of a Voice device(s) to be associated with the Voice VLAN. Syntax config voice_vlan oui [add | delete] mac <mac_address> mask < addr_mask> {description <desc 8> } To configure user-defined voice traffic OUIs.
  • Page 164 DGS-1100/ME Metro Ethernet Managed Switch CLI Reference Guide all - All ports are specified. state[enable | disable] – To enable/disable Voice VLAN function on the ports specified.The default state is disabled. mode - Specify the port voice VLAN mode to manual. When the switch receives LLDP-MED packets, it checks the VLAN ID, tagged flag and priority flag.The switch should follow the tagged flag and priority setting.

  • Page 165: Show Voice_Vlan Global

    DGS-1100/ME Metro Ethernet Managed Switch CLI Reference Guide show voice_vlan global Purpose Shows the Surveillance VLAN global information Syntax show surveillance_vlan global Description This command is used to show the Surveillance VLAN information. Parameters None. Restrictions None. Example usage: To show voice vlan global information: DGS-1100-24P/ME:admin#show voice_vlan global Command : show voice_vlan global Voice VLAN State : Enabled...

  • Page 166: Show Voice_Vlan Voice_Device

    DGS-1100/ME Metro Ethernet Managed Switch CLI Reference Guide To show voice vlan oui information: DGS-1100-24P/ME:admin#show voice_vlan oui Command: show voice_vlan oui OUI Address Mask Description -------------------------- ---------------------- ------------------ 00-01-e3-00-00-00 ff-ff-ff-00-00-00 Siemens 00-03-6b-00-00-00 ff-ff-ff-00-00-00 Cisco 00-09-6e-00-00-00 ff-ff-ff-00-00-00 Avaya 00-0f-e2-00-00-00 ff-ff-ff-00-00-00 Hua-3COM 00-60-b9-00-00-00 ff-ff-ff-00-00-00 NEC/Phil...

  • Page 167: Show Voice_Vlan Ports

    DGS-1100/ME Metro Ethernet Managed Switch CLI Reference Guide show voice_vlan ports Purpose Shows the Voice VLAN ports information. Syntax show voice_vlan ports [list <portlist> | all] Description This command is used to show the Voice VLAN ports information. Parameters list <portlist> - A range of port to display. all - All ports are specified.

  • Page 168: Dos Attack Prevention Commands

    DGS-1100/ME Metro Ethernet Managed Switch CLI Reference Guide DOS ATTACK PREVENTION COMMANDS The DoS commands in the Command Line Interface (CLI) are listed (along with the appropriate parameters) in the following table. Command Parameter [dos_type {land_attack state [ enable | disable ] | blat_attack state [ enable | disable ] | tcp_null_scan state [ enable | disable ] | tcp_xmascan state [ enable | config dos_prevention disable ] | tcp_synfin state [ enable | disable ] | tcp_syn_srcport_less_1024 state...

  • Page 169: Show Dos_Prevention

    DGS-1100/ME Metro Ethernet Managed Switch CLI Reference Guide Example usage: To configure DoS attack prevention on the switch: DGS-1100-24P/ME:admin#config dos_prevention dos_type land_attack state enable Command : config dos_prevention dos_type land_attack state enable Success. DGS-1100-24P/ME:admin# show dos_prevention Purpose To show the DoS prevention information on the switch. Syntax show dos_prevention {land_attack | blat_attack | tcp_null_scan | tcp_xmascan | tcp_synfin | tcp_syn_srcport_less_1024 |...

  • Page 170: Link Aggregation Commands

    DGS-1100/ME Metro Ethernet Managed Switch CLI Reference Guide LINK AGGREGATION COMMANDS The Link Aggregation commands in the Command Line Interface (CLI) are listed (along with the appropriate parameters) in the following table. Command Parameter create link_aggregation group_id <value> {type [lacp | static]} delete link_aggregation group_id <value>...

  • Page 171: Delete Link_Aggregation

    DGS-1100/ME Metro Ethernet Managed Switch CLI Reference Guide Example usage: To create a link aggregation group: DGS-1100-24P/ME:admin# create link_aggregation group_id 1 Command : create link_aggregation group_id 1 Success. DGS-1100-24P/ME:admin# delete link_aggregation Purpose To delete a previously configured link aggregation group. Syntax delete link_aggregation group_id <value>...

  • Page 172: Show Link_Aggregation

    DGS-1100/ME Metro Ethernet Managed Switch CLI Reference Guide Example usage: To define a load-sharing group of ports, group-id 2 with group members ports 1-5: DGS-1100-24P/ME:admin#config link_aggregation group_id 2 ports 1-5 Command : config link_aggregation group_id 2 ports 1-5 Success. DGS-1100-24P/ME:admin# show link_aggregation Purpose To display the current link aggregation configuration on the Switch.

  • Page 173: Lacp Commands

    DGS-1100/ME Metro Ethernet Managed Switch CLI Reference Guide LACP COMMANDS The LACP commands in the Command Line Interface (CLI) are listed (along with the appropriate parameters) in the following table. Command Parameter show lacp {ports <portlist>} config lacp_ports <portlist> mode [active | passive] Each command is listed in detail, as follows: show lacp Purpose...

  • Page 174: Config Lacp_Ports

    DGS-1100/ME Metro Ethernet Managed Switch CLI Reference Guide config lacp_ports Purpose To configure settings for LACP compliant ports. Syntax config lacp_ports <portlist> mode [active | passive] The config lacp_ports command is used to configure ports that Description have been previously designated as LACP ports. Parameters <portlist>...

  • Page 175: Eee

    DGS-1100/ME Metro Ethernet Managed Switch CLI Reference Guide The EEE commands in the Command Line Interface (CLI) are listed (along with the appropriate parameters) in the following table. Command Parameter config eee [portlist <portlist> | all] state [enable | disable] show eee {portlist <portlist>} Each command is listed in detail, as follows:...

  • Page 176: Show Eee

    DGS-1100/ME Metro Ethernet Managed Switch CLI Reference Guide show eee Purpose Used to show the eee function state on special port(s). Syntax show eee {portlist <portlist>} Description The show eee command is used to display the eee function state on the special port(s) Parameters portlist <portlist>...

  • Page 177: Appendix A - Ethernet Technology Sample Commands

    DGS-1100/ME Metro Ethernet Managed Switch CLI Reference Guide APPENDIX A - ETHERNET TECHNOLOGY SAMPLE COMMANDS This chapter will describe the features of the D-Link Switch and provide some background information about Ethernet/Fast Ethernet/Gigabit Ethernet switching technology. Gigabit Ethernet Technology Gigabit Ethernet is an extension of IEEE 802.3 Ethernet utilizing the same packet structure, format, and support for CSMA/CD protocol, full duplex, and management objects, but with a tenfold increase in theoretical throughput of over 100- Mbps Fast Ethernet and a hundredfold increase over 10-Mbps Ethernet.
  • Page 178 DGS-1100/ME Metro Ethernet Managed Switch CLI Reference Guide The switch acts as a high-speed selective bridge between the individual segments. The switch, without interfering with any other segments, automatically forwards traffic that needs to go from one segment to another. By doing this the total network capacity is multiplied, while still maintaining the same network cabling and adapter cards.

  • Page 179: Appendix B - Technical Specifications

    DGS-1100/ME: AC input, 100~240 VAC, - DGS-1100-16/ME: 32Gbps 50/60Hz, internal universal power supply Acoustic Value: - DGS-1100-18/ME: 36Gbps - DGS-1100-16/ME, 18/ME, 24/ME, 26/ME: - DGS-1100-24/ME: 48Gbps 0dB(A) (Fan-less) - DGS-1100-26/ME : 52 Gbps - DGS-1100-24P/ME: 44.5 dB(A) - DGS-1100-24P/ME : 48Gbps Operation Temperature 0~50°C...

  • Page 180: L2 Multicasting

    Bandwidth Control Security Storm Control DoS Attack Prevention D-Link Safeguard Management Telnet or D-Link Network Assistant Configuration backup / restoration via Telnet interface (CLI) Firmware backup & upgrade via Telnet interface (CLI) Reset, Reboot system Factory reset by pressing reset button...

  • Page 181: Appendix C - Rack Mount Instructions

    DGS-1100/ME Metro Ethernet Managed Switch CLI Reference Guide APPENDIX C – RACK MOUNT INSTRUCTIONS Safety Instructions - Rack Mount Instructions - The following or similar rack-mount instructions are included with the installation instructions: A) Elevated Operating Ambient - If installed in a closed or multi-unit rack assembly, the operating ambient temperature of the rack environment may be greater than room ambient.

This manual is also suitable for:

Dgs-1100-24/meDgs-1100-26/meDgs-1100-18/meDgs-1100-24p/me

Table of Contents