How To Use; Using The Remote Control - Sharper Image EVSI-UH201BK Instruction Manual And Warranty Information

How to Use

To reduce the risk of electric shock, this appliance is equipped with a
polarized plug (one blade is wider than the other). This plug will only fit in a
polarized outlet. If it still does not fit, contact a qualified electrician to install
the proper outlet. Do not change the plug in any way.
Power ON/OFF Button
Plug unit in to a 120 volt AC electrical outlet. Press the POWER ON/OFF
to turn unit on. Press the POWER ON/OFF
ATTENTION: When the water in the water tank is almost empty the power to the
unit will shut off to indicate to the user to refill water.
Mist Adjustment Setting
Mist adjust to three levels: 1, 2, 3. To increase the mist output, press the MIST
OUTPUT adjustment button. The mist level will be displayed on the LED display.
When changing the mist level using the remote control, press the MIST level button
once to display the current mist setting. Press it again quickly to advance the mist
setting. The mist level will return to level 1 if advanced past level 3.
Mist Temperature Setting
When the humidifier is powered ON, it will operate on the default setting, Cool Mist. To
change the Mist Temperature from Cool Mist to Warm Mist, press the WARM MIST
button. The mist temperature will change to Warm Mist, and WARM MIST button
will blink red while the mist is warming. When the mist has warmed, the light in the
WARM MIST button with remain steady. To change the Mist Temperature back to Cool
Mist, press the WARM MIST button again. The mist temperature will change to Cool
Mist, and the light in the WARM MIST button will turn off.
Programmable Humidistat
This unit has a Programmable Humidistat that can be set in 5% increments from
35% - 65% humidity, then Off. To program the humidity level, press the HUMIDITY
SET button. The humidity level will increase by 5% every time the button is pressed,
and will show on the LED display screen. Keep pressing the HUMIDITY SET button
until the desired humidity level setting is reached. The LED display will show the
set humidity level for 5 seconds, then will default back to display the current room
humidity. To cancel programmed humidity setting, keep pressing the HUMIDITY
SET until "- -" is read on the LED display.
NOTE: When the set humidity level is reached, the humidifier will turn off. When
the humidity level in the room drops below the set humidity level, the unit will
automatically turn on.
button
button again to turn unit off.
8
Night Light
Press the NIGHT LIGHT
button to turn on the Tank light. The light around the mist
knob will illuminate. Press the NIGHT LIGHT button again to turn the night light off.
Timer
The timer will cycle in 1HR increments from 1 – 12 Hours, then Off. Press the TIMER
button to activate the timer. The timer setting indicator on the LED display will read "01".
To select the desired timer setting, keep pressing the TIMER button until the desired
timer setting is lit on the timer setting indicator. The LED display will show the timer
setting for 3 seconds, then will default back to display the current room humidity. To
turn the timer Off, press the TIMER button until "00" is read on the LED Display.

Using the Remote Control

BEFORE FIRST USE, REMOVE PLASTIC PULL TAB FROM BATTERY COMPARTMENT.
Battery Installation
One CR2032 3V battery is included with the remote control. To change the battery, remove
the battery door at the back of the remote by squeezing the tab and pulling the door away
from the back of the remote. Please insert the battery into the remote with the positive side
up as shown on the drawer.
NOTE: Always keep the battery and remote control out of the reach of children.
BATTERY NOTE
• If the unit is not going to be used for a long period of time, remove batteries to
prevent damage due to possible battery leakage.
• Clean the battery contacts and also those of the device prior to battery installation.
• Remove used batteries promptly.
• Dispose of properly in accordance with all state, province, and country regulations.
• Do not dispose of batteries in fire. Batteries may explode or leak.
• Use only the size and type of batteries specified.
• When installing batteries, observe proper polarity +/-. Improper installation of batteries
may cause damage.
Bottom of Remote
Night Light
Power ON/OFF
ON/OFF
NIGHT LIGHT
Warm Mist
Mist Level
L M H WM MIST
Timer
Humidistat
TIMER HUMI. SET
SHARPER IMAGE
®
9