Table of Contents
Advertisement
HCD-J300
QQ
3 7 63 1515 0
5. USING THE CONTINUOUSLY RECORDED DISC
* This disc is used in focus bias adjustment and error rate check.
The following describes how to create a continuous recording
disc.
1. Insert a disc (blank disc) commercially available.
2. Press the
. "R"
or
> "R"
(C35).
3. Press the
ENTER/YES "R"
MID".
Display "CREC 1(0300)" and start to recording.
4. Complete recording within 5 minutes.
5. Press the
button and stop recording .
MENU/NO "R"
6. Press the Z (MD) button and remove the disc.
The above has been how to create a continuous recorded data for
the focus bias adjustment and error rate check.
Note: Be careful not to apply vibration during continuous recording.
6. CHECKS PRIOR TO REPAIRS
These checks are performed before replacing parts according to
"approximate specifications" to determine the faulty locations. For
details, refer to "Checks Prior to Parts Replacement and Adjustments
in MD" (see page 26).
6-1. Temperature Compensation Offset Check
When performing adjustments, set the internal temperature and room
temperature to 22 to 28ºC.
Procedure:
1. Press the
or
. "R"
> "R"
CHECK" (C12).
TE
2. Press the
ENTER/YES "R"
button.
L 13942296513
3. "T=@@(##) [OK]" should be displayed. If "T=@@ (##) [NG]"
is displayed, it means that the results are bad.
(@@ indicates the current value set, and ## indicates the value
written in the non-volatile memory.)
6-2. Laser Power Check
Before starting adjustment;
The laser power adjustment value changes depending upon the types
of the optical pick-up (KMS-260B or KMS-260E).
Check the type of the optical pick-up before starting adjustment.
(See the illustrations "The method of ideutifying the optical pick-
up" on page 36)
Before checking, check the Iop value of the optical pick-up.
(Refer to 8. Recording and Displaying the Iop Information (see page
35)
Connection:
Optical pick-up
objective lens
www
BD board
CN105 pin 1 (I+3V)
CN105 pin 2 (IOP)
.
32
http://www.xiaoyu163.com
button and display "CREC 1MODE"
button again to display "CREC 1
button to display "TEMP
laser
power meter
digital voltmeter
+
x
ao
y
–
i
http://www.xiaoyu163.com
8
Procedure:
1. Set the laser power meter on the objective lens of the optical
pick-up. (When it cannot be set properly, press the m
or M
button to move the optical pick-up.)
"R"
Connect the digital volt meter to CN105 pin 1 (I+3V) and
CN105 pin 2 (IOP).
2. Then, press the
."R"
"LDPWR CHECK" (C13).
3. Press the
ENTER/YES "R"
0.9mW$ ". Check that the reading of the laser power meter
becomes specified value.
SPECIFIED VALUE
4. Press the
ENTER/YES "R"
8.4mW$ ". Check that the reading the laser power meter and
digital volt meter satisfy the specified value.
Specified Value:
Laser power meter reading :
KMS-260B
6.8 to 7.2 mW
KMS-260E
7.0 to 7.5 mW
Digital voltmeter reading : Optical pick-up displayed value ± 10%
(Optical pick-up label)
KMS260B
20101
Q Q
H0576
3
6 7
1 3
lOP=57.6 mA in this case
lOP (mA) = Digital voltmeter reading (mV)/1 ( Ω )
5. Press the
MENU/NO "R"
(C13) and stop the laser emission.
(The
MENU/NO "R"
laser emission.)
Note: After step 4, each time the
display will be switched to "LD 0.7W$
"LD WP
$
Checking Location: BD board (see page 39)
6-3. Iop Compare
The current Iop value at laser power 8.4 mW output and reference
Iop value (set at shipment) written in the nonvolatile memory are
compared, and the rate of increase/decrease will be displayed in
percentage.
Note: Perform this function with the optical pick-up set at room tempera-
ture.
Procedure:
1. Press the
."R"
or
(C27).
2. Press the
ENTER/YES "R"
3. When measurements complete, the display changes to "± xx%
yy".
u163
xx is the percentage of increase/decrease, and OK or NG is
displayed at yy to indicate whether the percentage of increase/
.
decrease is within the allowable range.
4. Press the
MENU/NO "R"
2 9
9 4
2 8
or
>"R"
button and display
button once and display "LD
KMS-260B
0.85 to 0.91 mW
KMS-260E
0.90 to 0.96 mW
button once more and display " LD
For details of the method for
checking this value, refer to
"8. Recording and Displaying
1 5
the Iop Information"
0 5
8
2 9
9 4
button and display "LDPWR CHECK"
button is effective at all times to stop the
ENTER/YES "R"
button is pressed, the
"and "LD 7.5mW$
". Nothing needs to be performed here.
> "R"
button to display "Iop Compare"
button and start measurements.
m
co
button to end.
9 9
button
"R"
2 8
9 9
"
Hide quick links:
Advertisement
Table of Contents
