Table of Contents
Advertisement
P P P
P
P
PECO
PECO
PECO
PECO
PECO
OPERATOR'S MANUAL
Briggs & Stratton 6.5HP Vanguard Engine Driven Models:
06131510 (54" Deck) - (Z915B, Z920M, Z920R, Z925M EFI, Z930R)
06131513 (60" Deck) - (Z915B, Z920M, Z925M EFI, Z930M,
Briggs & Stratton 900 Series Engine Driven Models:
06131511 (54" Deck) - (Z915B, Z920M, Z920R, Z925M EFI, Z930R)
06131514 (60" Deck) - (Z915B, Z920M, Z925M EFI, Z930M,
PTO Models:
06131512 - Z915B 54" (CV740 Kohler)
06131515 - Z915B 60" (CV740 Kohler)
06131516 - Z930R 54" (FX801V Kawasaki)
06131517 - Z930M/Z930R 60" (FX801V Kawasaki)
ASSEMBLY OPERATION MAINTENANCE
MANUAL PART#: Q0477
COLLECTION
Z930M EFI, Z930R, Z950R, Z960R)
Z930M EFI, Z930R, Z950R, Z960R)
GRASS
SYSTEM
Designed For:
Z900 Series
2013-2014
Advertisement
Table of Contents
Related Manuals for Peco 06131512
Summary of Contents for Peco 06131512
- Page 1 06131514 (60” Deck) - (Z915B, Z920M, Z925M EFI, Z930M, Z930M EFI, Z930R, Z950R, Z960R) PTO Models: 06131512 - Z915B 54” (CV740 Kohler) 06131515 - Z915B 60” (CV740 Kohler) 06131516 - Z930R 54” (FX801V Kawasaki) 06131517 - Z930M/Z930R 60” (FX801V Kawasaki)
-
Page 2: Table Of Contents
PECO GRASS COLLECTION SYSTEM TABLE OF CONTENTS SECTION PAGE SECTION PAGE Safety - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 2... -
Page 3: Safety Alert Symbol
SAFETY WARNING! NEVER operate the mower unless the discharge guard and either the deflector assembly or the vacuum collector adapter are fastened securely in place. WARNING! Do not work around the mower deck boot or the blower area until you are certain that the mower blades and the blower impeller have stopped rotating. -
Page 4: Warranty
PECO elects, without charge if the defect appears within 90 days from the date of installation of such part or before the expiration of the original warranty period, whichever is later. -
Page 5: Introduction And Description
Section I - INTRODUCTION AND DESCRIPTION 1-1 Introduction 1-2 Description We are pleased to have you as a PECO customer. Your The grass collection system is designed for turf collection system has been designed to give you a low maintenance where there is a need to collect the grass maintenance, simple, and effective way to collect the clippings as the mower cuts the turf. -
Page 6: Installation For Use
Section II - INSTALLATION FOR USE 2-1 Preparation Of Mower Upon pressing the engine pulley to the clutch, replace the completed assembly to the mower’s engine shaft to fasten. PTO Drive Models Only From the underside of the engine, disconnect the wiring Kohler CV740 harness attached to the electric clutch. -
Page 7: Frame Bracket Installation
2-2 Frame Bracket Installation Secure the rear frame bracket P#(B0867) to the left and Secure the right frame bracket P#(B0866) to the rear right frame bracket, using (4) 3/8”-16 x 1” HHCS frame of the mower, using (1) existing metric hex bolt, P#(K1191) and (4) 3/8”-16 nylon flange locknuts (2) 5/16”-18 x 1”... -
Page 8: Exhaust Diverter Installation
2-3 Exhaust Diverter Installation An exhaust diverter will need to be installed on your mower to prevent the exhaust from damaging the PTO assembly or Engine/Blower/Blade Assembly. Kohler CV740 Engines Attach (1) diverter P#(J0290) to the engine exhaust pipe. Kawasaki FX801V Engines Attach (1) exhaust diverter P#(J0293) and (1) clamp kit P#(X1025) to the engine exhaust pipe. -
Page 9: Pto Mount Plate Component Installation
2-4 PTO Mount Plate Component Installation PTO Drive Models Only Secure the PTO stop plate P#(B0736) to the left PTO mount plate P#(B0868) and right PTO mount plate P#(B0869) using (4) 1/4”-20 x 3/4” HHCS P#(K1222) Right PTO and (4) 1/4”-20 nylon flange locknuts P#(K2014). Leave Mount Plate the hardware finger tight until all of the PTO mount plate components are installed. -
Page 10: Pto Assembly Installation
2-5 PTO Assembly Installation PTO Drive Models Only Note: Remove the gearbox pulley guard in preparation Lift the PTO Assembly P#(A1950) into position as shown for the belt installation. Refer to Figure 2-5c. in Figure 2-5a, inserting the PTO pivot pin into the slots on the left and right PTO mount plates. -
Page 11: Belt Installation And Adjustment
Connect the belt A56K P#(M0239) from the engine 2-7 Belt Installation and Adjustment pulley to the lower gear box pulley (Figure 2-7d). PTO MODELS ONLY Figure 2-7d Loosen the (4) bolts P#(K1191), (2) on each side, that Connect Belt secure the gear box assembly to the PTO assembly To Both Pulleys P#(A1950) (Figure 2-7a and 2-7b). -
Page 12: Cam Assembly Adjustment
2-8 Cam Assembly Adjustment 2-10 Engine Mount Arm Assembly PTO MODELS ONLY Installation The cam assembly P#(A0422), which controls the Engine Drive Models Only blower belt tension, comes from the factory pre-adjusted. Insert the engine mount arm assembly P#(A0274) into If the belt is too tight or becomes too loose, remove the the outer engine mount tube and secure using (1) detent hair pin clip P#(K0099) from the belt tension rod... -
Page 13: Lower Mount Tube Installation
2-12 Lower Mount Tube Installation 2-13 Upper Frame Assembly Installation Secure the (2) lower mount tubes P#(B0640) to the rear frame bracket using (2) 5/16”-18 u-bolts P#(K1098) and Position the upper frame assembly P#(A1058) above the (4) 5/16”-18 nylon flange locknuts P#(K2516) PER lower mount tubes as shown in Figure 2-13. -
Page 14: Top Assembly To Upper Frame Assembly Installation
2-14 Top Assembly To Upper Frame 2-16 Inlet Installation Assembly Installation Position the top assembly P#(A1158) above the upper Slide the inlet P#(V0025) into the hole on the bagger top frame assembly as shown in Figure 2-14. Fasten the top until the inlet locks into place. -
Page 15: Blower Cone Installation
2-17 Blower Cone Installation 2-18 Boot To Mower Deck Installation 54” Deck Thread (1) 5/16”-18 jam nut P#(K0120) onto each end of Secure the boot plate P#(B0001) to the aluminum boot (2) 5/16”-18 x 2-1/2” HHCS P#(K0125) as shown in P#(E1103) using (2) 3/8”-16 x 1”... -
Page 16: Hose Clamp Preparation
Step 3: Using a flat file or disc grinder, remove sharp 2-19 Hose Clamp Preparation edges from clamp cut in Step 2. Refer to Figure 2-19d. CAUTION Figure 2-19d Note: To prevent injury, wear safety gear when cutting or grinding hose clamps. Remove Sharp Edge From Hose Clamp The hose clamps P#(J1000), provided with your... -
Page 17: Length Of Hose Adjustment
2-20 Length Of Hose Adjustment 2-22 Lower Hose To Blower Cone Installation The hoses in steps 2-21 and 2-22 must be cut to fit your machine. Follow steps 2-21 and 2-22. Do not cut the Slide a pre-assembled hose clamp P#(J1000) over both hoses until you have tried to fit them on your machine. -
Page 18: Impeller Blade Removal And Replacement
2-24 Impeller Blade Removal/Replacement Tips on removing impeller blade; To gain impeller blade (#1) access, first remove the blower cone (#2) from the blower housing, located on 1 - Try carefully hitting the base of the impeller blade (#1), between each vein (#12), with a rubber mallet to the PTO assembly P#(A1821), by removing two blower loosen the taper-lock bushing hold. -
Page 19: Weight Kit Installation
2-25 Weight Kit Installation A custom front counterweight kit must be installed on NOTE: It is recommended that (2) people install the your mower before operating the collection system. If weight bar. Using a floor jack or similar device, position equipped, remove the existing weight from the front the weight bar P#(B0035) under the weight bracket as mower frame. -
Page 20: Throttle Cable Kit Installation
2-26 Throttle Cable Installation NOTE: Engine Driven Models Only Figure 2-26c To install the throttle cable kit to the ROPS (roll over protection system), place the 3/8” U-Bolt P#(K0136) onto the ROPS with the threads facing the front of the mower. -
Page 21: Installation And Removal Of Collection Bags
2-27 Installation/Removal Of Figure 2-27c Collection Bags Plastic Top IMPORTANT! To prevent bag wear, install (2) red plastic end caps P#(J0274), as shown in Figure 2-27a, on each bag ring before installing bags. Figure 2-27a Bag Ring Red Plastic End Caps Fasten Draw -Latch Here &... -
Page 22: Exploded Views And Parts List
Exploded Parts View A1158 Top Assembly Item # Doc # Title V0022 PRO 3 BAGGER TOP B0676 Hinge Stop Pl. K0114 BLACK PLASTIC RIVET C0069 DUST GUARD BRACE K1030 1/4"-20 x 1-1/4" CARRIAGE BOLT J4009 SHORT RUBBER STRAP W/ S HOOK K0037 1/4"... - Page 23 Exploded Parts View A1950 PTO Assembly...
- Page 24 PTO Parts List A1950 PTO Assembly Item Document Title Quantity Number Number A0429 GEAR BOX ASSEMBLY K0348 3/8"-16 x 2" ALL THREAD HHCS K0047 3/8" FLAT WASHER 1.00 OD x .446 ID x .075 T K0353 1/4"-20 x 1/2" HHSTS K1159 5/16"-18 x 2"...
-
Page 33: Operating Instructions
* Remember that horsepower requirements will vary with SECTION III the mowing conditions such as type and height of turf grass, moisture content, amount of leaves, whether the OPERATING INSTRUCTIONS terrain is flat or hilly, etc. 3-1 General Safety 3-3 Disengagement Of The Blower Only qualified people familiar with this operator’s manual PTO MODELS and the mower’s operator’s manual should operate this... -
Page 34: Lubrication
5-1 Parts And Service Information 7. Check for wear or deterioration of the upper or lower PECO collection system owners should record the name hoses. If there are any portions of the hose that have and telephone number of their Service Center. Your... -
Page 35: Safety Decals
SAFETY DECALS To promote safe operation, PECO supplies safety decals on all products manufactured. Damage can occur to safety decals either through shipment, use or reconditioning. Contact your local Service Center for replacement decals. Part #: R1051 Warning: Hearing Protection Label... - Page 37 NOTES:...
- Page 38 P P P PECO PECO PECO PECO PECO 100 AIRPORT ROAD ARDEN, NORTH CAROLINA 28704 (800) 438-5823 OR (828) 684-1234 FAX: (828) 684-0858 EMAIL: peco@lawnvac.com WEBSITE: www.lawnvac.com...