Page 1
HTC-NX300 SERVICE MANUAL E Model Chinese Model Ver 1.1 2001.09 HTC-NX300 is the CD player and Tape Deck section in MHC-NX300AV. Dolby noise reduction manufactured under license Model Name Using Similar Mechanism from Dolby Laboratories Licensing Corporation. CD Mechanism Type CDM53E-K3BD37 “DOLBY”...
LINE WITH MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUB- LISHED BY SONY.
SECTION 1 SERVICING NOTES SELF-DIAGNOSIS This appliance is classified as a CLASS 1 LASER product. The CLASS 1 LASER PRODUCT MARKING is located on This unit is equipped with a self-diagnosis function. the rear exterior. The function is used for diagnosing the conditions of the circuits of the VIDEO board.
Page 4
POWER SUPPLY DURING SERVICING Connection: Connector cable (17P) of • As this set has not own power supply, it does not operate inde- attachment to power feed jig pendently. Therefore, during servicing, connect it to the Pre- Main amplifier and Tuner Unit (STR-NX300) of MHC- Relay connector jig NX300AV.
Page 5
OPTICAL PICK-UP CLEANING 1 Remove the case. (Refer to disassembly page 7) 2 four screws (BVTP M2.6) 3 Open the magnet ass’y. Note 1: In cleaning the lens, do not apply an excessive force. 4 Cleaning the As the optical pick-up is vulnerable, application of optical pick-up.
SECTION 2 GENERAL • LOCATION OF CONTROLS – Front Panel – 1 G (CD) button and indicator 2 S (CD) button and indicator 3 s (CD) button 4 DISC1 to 5 buttons and indicators 5 A (DISC1 to 5) buttons and indicators 6 RETURN button 7 NEXT button 8 PREV button...
SECTION 3 DISASSEMBLY Note: Follow the disassembly procedure in the numerical order given. CASE 1 screw (BVTP3 × 10) 3 Remove the case 2 two screws in the arrow A (case 3 TP2) direction. 2 two screws (case 3 TP2) FRONT PANEL SECTION 6 two screws (BVTP3 ×...
Page 8
CD MECHANISM DECK SECTION (CDM53E-K3BD37) 4 Remove the CD mechanism deck section (CDM53E-K3BD37) in 3 four screws the arrow A direction. (BVTP3 × 10) to fitting base (guide) ass’y, bracket (chassis) and magnet ass’y (page 10) 1 flat cable (17 core) (12 cm) (CN112) 2 connector (CN713)
Page 9
CD BASE UNIT (BU-K3BD37) 4 CD base unit (BU-K3BD37) 3 compression spring 2 compression spring (black) (silver) 1 two screws 1 two screws (PTPWH M2.6) (PTPWH M2.6) VIDEO BOARD 7 SVCD shield (U) 6 screw (BVTT3 × 5) 6 screw (BVTT3 ×...
Page 10
FITTING BASE (GUIDE) ASS’Y, BRACKET (CHASSIS) AND MAGNET ASS’Y 7 four screws (BVTP M2.6) 5 bracket (chassis) 2 four screws (BVTP M2.6) 4 two screws (BVTP M2.6) 6 connector (CN710) 8 magnet ass’y from CD mechanism deck section 4 three screws (CDM53E-K3BD37) (BVTP M2.6) (page 8)
Page 11
TRAY (SUB) 1 Rotating the pulley (LD), shift the slider (selection) in the arrow A direction. 2 Rotating the pulley (mode) in the arrow direction, adjust the tray (sub) to be removed. 3 Rotating the pulley (LD), shift the slider (selection) in the arrow B direction. 4 Rotating the pulley (mode) in the arrow direction, remove the tray (sub) to be removed.
Page 12
GEARS INSTALLATION 3 gear (gear B) portion A Adjust the gear (gear B) with the portion A as shown. 1 Slide the slider (U/D) fully in the arrow direction. 4 gear (gear A) 2 gear (U/D slider) gear slider (U/D) gear linearly (gear B) Adjust so as to be aligned with...
Page 13
STOCKER SECTION INSTALLATION 2 portion A of tray (sub) Hook the portion A of tray (sub) 1 stocker section to the slider (selection). potion A sticking of of tray (sub) slider (selection) 3 two step screws 3 two step screws CHASSIS (MOLD B) SECTION INSTALLATION 3 three screws (BVTP M2.6)
SECTION 4 TEST MODE [LED All Lit, Key Check Mode] [VIDEO CD Color-bars Mode] Procedure: On this mode, the data of the color-bars signal as a picture signal 1. Press the button to turn the power ON. and the 1 kHz sine wave signal as a sound signal are output by the 2.
SECTION 5 SECTION 6 MECHANICAL ADJUSTMENTS ELECTRICAL ADJUSTMENTS Precaution TAPE DECK SECTION 0 dB=0.775 V 1. Clean the following parts with a denatured alcohol-moistened swab: 1. Demagnetize the record/playback head with a head demagne- record/playback heads pinch rollers tizer. erase head rubber belts 2.
Page 16
DECK B 2. Turn the adjustment screw and check output peaks. If the peaks Tape Speed Adjustment do not match for L-CH and R-CH, turn the adjustment screw so that outputs match within 1dB of peak. • Execute only if connected to the STR-NX300 Mode: Playback test tape AUDIO OUT jack...
Page 17
DECK B REC Bias Adjustment Specified value: AUDIO OUT jack PB level: 47.2 to 53.0 mV (–24.3 to –23.3 dB) Procedure: 1. Mode: Record Adjustment Location: MAIN board AUDIO IN jack – MAIN BOARD (Conductor Side) – 1) 315 Hz ...
2. RF LEVEL CHECK CD SECTION Note: oscilloscope 1. CD Block is basically designed to operate without adjustment. There- fore, check each item in order given. BD board 2. Use YEDS-18 disc (3-702-101-01) unless otherwise indicated. 3. Use an oscilloscope with more than 10 MΩ impedance. TP (RF) 4.
Connecting points: VIDEO SECTION Note: – BD BOARD (Side B) – 1. Perform measurement by connecting to the STR-NX300. Frequency Adjustment Connection: frequency counter VIDEO board TP (27 MHz) – (RF) IC102 (VC) (AGCCON) Procedure: (TEO) 1. Connect the frequency counter to TP (27 MHz) on VIDEO board.
HTC-NX300 7-2. BLOCK DIAGRAM – AUDIO/VIDEO CD Section – DIGITAL FILTER, D/A CONVERTER CN101 (1/4) IC509 MCLK 33.8MHz SYSTEM CONTROL (TO STR-NX300AV) (Page 21) MPEG VIDEO/AUDIO DECODER, DIGITAL VIDEO SIGNAL PROCESSOR VOUTL DA-DATA DATA CD. L MPEG AUDIO INPUT FILTER,...
7-5. NOTE FOR PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS • Circuit Boards Location (In addition to this, the necessary note is printed in each block) Note on Printed Wiring Board: Note on Schematic Diagram: • X : parts extracted from the component side. •...
HTC-NX300 7-6. PRINTED WIRING BOARD – BD Board – • See page 25 for Circuit Boards Location. (Page 30) • Semiconductor • Semiconductor Location Location (Side A) (Side B) Ref. No. Location Ref. No. Location IC104 IC101 IC102 Q101 IC103...
Page 27
HTC-NX300 7-7. SCHEMATIC DIAGRAM – BD Board – • See page 44 for Waveforms. • See page 44 for IC Block Diagrams. (Page 28) • Voltages and waveforms are dc with respect to ground under no-signal condition. no mark : CD PLAY The components identified by mark 0 or dotted line with mark 0 are critical for safety.
HTC-NX300 7-8. SCHEMATIC DIAGRAM – VIDEO Board (1/2) – • • See page 31 for Waveforms. See page 47 for IC Block Diagram. (Page 27) (Page (Page 29) (Page 29) (Page 29) (Page 29) • Voltages and waveforms are dc with respect to ground under no-signal conditions.
HTC-NX300 7-9. SCHEMATIC DIAGRAM – VIDEO Board (2/2) – • • See page 31 for Waveforms. See page 47 for IC Block Diagram. (Page 28) (Page 28) (Page 28) (Page 28) • Voltages and waveforms are dc with respect to ground under no-signal conditions.
HTC-NX300 7-11. PRINTED WIRING BOARDS – CD MOTOR/SENSOR Section – • See page 25 for Circuit Boards Location. TO OUT SW BOARD TO IN SW BOARD TO CONNECTOR BOARD TO SENSOR BOARD (Page 37) TO CLAMP TO INT/ MOTOR COUNT SW...
HTC-NX300 • Voltages are dc with respect to ground under no-signal conditions. no mark : CD PLAY 7-12. SCHEMATIC DIAGRAM – CD MOTOR/SENSOR Section – • See page 46 for IC Block Diagram. (Page 39) (Page 39)
HTC-NX300 7-14. SCHEMATIC DIAGRAM – AUDIO Board – • See page 46 for IC Block Diagram. PB EQ AMP (PLAYBACK) (DECK A) PB LEVEL (L) (DECK A) PB LEVEL (R) (DECK A) PB EQ AMP (DECK B) PB LEVEL (L) (DECK B) A +7.5V...
HTC-NX300 7-15. PRINTED WIRING BOARD – LEAF SW Board – • See page 25 for Circuit Boards Location. DECK B DECK A PLUNGER PLUNGER (DECK B PLAY) (DECK B 120/70) (DECK A PLAY) (DECK B HALF) (DECK A REC) (DECK A 120/70)
HTC-NX300 7-18. SCHEMATIC DIAGRAM – MAIN Board (1/2) – (Page 41) (Page 41) (Page 41) (Page 41) (Page 41) (Page 39) (Page 35) (Page 36) (Page 39) • Voltages are dc with respect to ground under no-signal conditions. no mark : CD PLAY...
HTC-NX300 7-21. SCHEMATIC DIAGRAM – POWER Board – (Page 38) (Page 38) (Page 38) (Page 38) (Page 38) • Voltages are dc with respect to ground under no-signal conditions. no mark : CD PLAY...
HTC-NX300 7-23. SCHEMATIC DIAGRAM – PANEL Section – (Page 39) (Page 39) (Page 39) • Voltages are dc with respect to ground under no-signal conditions. no mark : CD PLAY...
Page 47
– VIDEO Baord – IC509 PCM1727E-2/T2 384fs CLOCK MANAGER • DUAL PLL DGND PGND POWER SUPPLY SCKO1 SCKO2 MCKO LRCK AUDIO SCKO3 DATA INPUT DATA INTERFACE MODE CONTROL RSTB ZERO OPEN 8 TIME OVER SAMPLING DIGITAL FILTER • FUNCTION CONTROL 14 VOUTL MULTI LEVEL MULTI LEVEL...
7-24. IC PIN FUNCTION DESCRIPTION • MAIN BOARD IC101 M30622MA-A30FP (SYSTEM CONTROLER) Pin No. Pin Name Description CD DATA Serial data output terminal Not used (open) CD CLK Serial data transfer clock signal output terminal Not used (open) Serial data latch pulse output terminal Not used (open) Reset signal output to the CD mechanism controller (IC505) on the CD block XRST “L”: reset...
Page 49
Pin No. Pin Name Description XHOLD Not used (pull down) LED A CDPL LED drive signal output of the G (CD) indicator (D211) “L”: LED on LED A RECP LED drive signal output terminal Not used (open) LED R RECP LED drive signal output of the REC PAUSE/START indicator (D217) “H”: LED on LED SYNC...
Page 50
Pin No. Pin Name Description CAPM-CNT2 Capstan motor (M1) drive signal output terminal “H” active *3 CAPM-CNT1 Capstan motor (M1) drive signal output terminal “H” active *3 High/normal speed selection signal output of the capstan motor (M1) CAP-M-H/L “L”: normal speed, “H”: high speed Whether a music is present or not from the HA12215F (IC301) is detected an automatic music AMS-IN sensor “L”: music is present, “H”: music is not present...
Page 51
• VIDEO BOARD IC505 M30624MGA-A17FP (CD MECHANISM CONTROLLER) Pin No. Pin Name Description SENSE Internal status (SENSE) signal input from the CXD3008Q (IC101) SENSE CLK Sense serial data reading clock signal output to the CXD3008Q (IC101) DSP DATA Serial data output to the CXD3008Q (IC101) DSP LATCH Serial data latch pulse output to the CXD3008Q (IC101) DSP CLK...
Page 52
Pin No. Pin Name Description 42, 43 Not used (open) BUS XRD Bus read signal output to the MPEG video/audio decoder (IC506) Vertical synchronized signal input Not used (open) BUS XWR Bus write signal output to the MPEG video/audio decoder (IC506) 8830-CS Chip select signal output to the MPEG video/audio decoder (IC506) AUDIO MUTE...
Page 53
• VIDEO BOARD IC506 CL8830-PD0 (MPEG VIDEO/AUDIO DECODER, VIDEO SIGNAL PROCESSOR) Pin No. Pin Name Description PIO0 Programmable I/O terminal Not used (open) Two-way data bus with the D-RAM (IC507) and CD mechanism controller (IC505) 2 to 4 MD0 to MD2 Data input from the program ROM (IC508) —...
Page 54
Pin No. Pin Name Description — Ground terminal Two-way data bus with the D-RAM (IC507) and CD mechanism controller (IC505) Data input from the program ROM (IC508) — Power supply terminal (+3.3V) MD15 Two-way data bus with the D-RAM (IC507) —...
Page 55
Pin No. Pin Name Description MA2, MA4, MA3 110 to 112 Address signal output to the D-RAM (IC507) and program ROM (IC508) — Power supply terminal (+3.3V) MA12 Address signal output to the D-RAM (IC507) and program ROM (IC508) — Ground terminal MA13 Address signal output to the D-RAM (IC507) and program ROM (IC508)
Page 56
Pin No. Pin Name Description — Power supply terminal (+3.3V) DA-XCLK Main reference clock signal (16.9344 MHz=384fs) from the D/A converter (IC509) — Ground terminal DAI-DATA Digital audio data input from the D/A converter (IC509) DAI-LRCK Digital audio L/R sampling clock signal (44.1 kHz) input from the D/A converter (IC509) DAI-BCK Digital audio bit clock signal (2.8224 MHz) input from the D/A converter (IC509) PIO9...
SECTION 8 EXPLODED VIEWS NOTE: • -XX and -X mean standardized parts, so they • Items marked “*” are not stocked since they The components identified by mark 0 or dotted line with mark may have some difference from the original are seldom required for routine service.
Page 60
(4) CD MECHANISM DECK SECTION-2 (CDM53E-K3BD37) not supplied not supplied S707 not supplied M701 supplied BU-K3BD37 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 4-985-672-01 SCREW (+PTPWH M2.6), FLOATING * 226 1-671-507-11 CLAMP MOTOR BOARD 4-220-933-01 INSULATOR 4-211-221-01 GEAR (LD MOVABLE) 4-211-212-51 TRAY (SUB) 4-211-217-01 GEAR (SELECTION)
Page 61
Ver 1.1 (5) CD BASE UNIT SECTION (BU-K3BD37) not supplied not supplied M101 M102 The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified. Ref. No. Part No. Description Remark Ref.
Page 62
(6) TAPE MECHANISM DECK SECTION-1 (TCM-230AWR2) HP101 HRPE101 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 3-376-464-11 SCREW (+PTT 2.6X6), GROUND POINT * 409 A-2007-731-A AUDIO BOARD, COMPLETE 3-036-914-01 RIVET 3-016-573-03 LEVER (EJECT PREVENTION R) 3-016-574-11 SPRING (HEAD), TENSION 3-032-810-02 SPRING (R), TORSION X-3374-156-4 PINCH LEVER (REV) ASSY 3-016-572-01 LEVER (EJECT PREVENTION L)
SECTION 9 AUDIO ELECTRICAL PARTS LIST NOTE: • Due to standardization, replacements in the • Items marked “*” are not stocked since they The components identified by mark 0 or dotted line with mark are seldom required for routine service. parts list may be different from the parts speci- 0 are critical for safety.
Page 73
VIDEO Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark JW526 1-216-295-00 SHORT R521 1-216-073-00 METAL CHIP 1/10W JW527 1-216-295-00 SHORT R522 1-216-025-00 RES-CHIP 1/10W JW538 1-216-295-00 SHORT JW539 1-216-295-00 SHORT R524 1-216-025-00 RES-CHIP 1/10W JW541 1-216-295-00 SHORT R525 1-216-057-00 METAL CHIP 2.2K...
HTC-NX300 REVISION HISTORY Clicking the version allows you to jump to the revised page. Also, clicking the version at the upper right on the revised page allows you to jump to the next revised page. Ver. Date Description of Revision 2001.09...