Advertisement
4.
Apply sealant (not supplied) to the bottom of the vertical pipe and around the bolt
holes to prevent water or other contaminants from entering the mount.
5.
Screw the mount kit to the parapet/flat roof mount.
6.
Connect the cables to the camera (see
a Micro SD card, install it before connecting the cables.
Feed cables
through the
mount kit
Note
Check that the eyelet cable connection is secure and carrying all of the load of the
camera after making all cable connections.
7.
Attach the camera to the mount kit, and then tighten the security screw on the top of
the camera.
Note
Optional: Use the lubricant on the dome cover's rubber ring to make it easier to
re-attach to the housing and seal the PTZ dome cover and housing without water
coming in. Be careful to not get any lubricant on the dome as it may interfere with
viewing PTZ images.
Cable Connections
Before connecting the cables, take a minute to familiarize yourself with the camera's back
plate connectors, switches, and buttons, as shown in the figures and table below.
HDZ Indoor Dome Cameras
B
E
F
C
A
G
D
A
RJ45 connector
b
B
Alarm input/output
b
C
Power
c
D
Micro SD memory card slot
a. Press the factory reset button to restore the factory default settings to the camera.
b.Alarm, power, and audio connections are made with removable connectors.
c. It is recommend that you use a high quality micro SD card (up to 64 GB; microSDXC 64 GB
support tested with SanDisk SDXC 64 GB) that has a class 10 minimum write speed (8 GB
MLC/16 GB MLC or TLC/32 GB TLC). Insert the card before finishing camera installation.
The card must be formatted using the Honeywell Web GUI before it can be used for
recording.
Cable
Connections, below). If you are using
Screw the mount kit onto
the parapet mount
Tightly fix the screw at the
top of the camera after
connecting the three parts
Attach the
camera body to
the mount kit
HDZ Outdoor Dome Cameras
B
E
F
C
D
A
G
a
E
Factory reset button
b
F
Audio input/output
G
Eyelet for attaching security cable
Connecting Audio
Refer to the following figure and table when making audio connections to your camera.
Pin
Definition
1
Line out
2
GND
3
Line in
1 2 3
Connecting Alarm Inputs/Outputs
Refer to the following figure and table when making alarm connections to your camera:
1 2 3 4 5 6 7 8 9 10 11 12
Pin
Definition
Pin
1
Alarm Out NO 1
5
2
Alarm Out NC 1
6
3
Alarm Out COM 1
7
4
GND
8
Connecting the Network Cable
To power the camera, either PoE or a 24 V AC power connection can be used. If using
PoE, either a switch or PoE injector meeting the PoE+ standard (30 W) or High Power
over PoE (60 W), depending on the model, must be employed (see table below).
HDZ Camera Model
HDZ22HD(X), HDZ30(X), HDZ30HD
HDZ22HDE(X), HDZ30HDE, HDZ36E(X)
Connect an Ethernet cable to the RJ45 connector on the back plate of the camera (see
figure above). The Ethernet cable should not be longer than 328 ft (100 m). After you have
connected the cable, check the status of the LED indicators on the RJ45 connector. (If the
LEDs are not lit, re-check the connection.)
•
The green LED indicates a network connection.
•
The orange LED indicates network activity.
Note
You may need to use a crossover cable if you are connecting the camera directly
to a PC.
Connecting Power
Refer to the following figure and table when connecting power to your camera through
the main power adapter.
Note
Please use the minimum power adapter for:
HDZ30(X): 24 V AC, ~1.0 A MAX / PoE+, 21.0 W
HDZ36E(X): 24 V AC, ~3.3 A MAX / PoE++, 57.0 W
1
2
3
HDZ22HD(X), HDZ30HD: 24 V AC, ~1.3 A MAX /
PoE+, 25.5 W
Pin
Definition
HDZ22HDE(X), HDZ30HDE: 24 V AC, ~3.3 A MAX /
1
24 V AC
PoE++, 60.0 W
2
FG
3
24 V AC
Important Note:
Regarding PoE Operation of models HDZ22HDE(X), HDZ36E(X) and
HDZ30HDE
A high power PoE injector capable of supplying at least 60 W is required for proper
operation of outdoor camera model HDZ22HDE(X), HDZ36E(X) and HDZ30HDE as PoE
to IEEE802.3af or IEEE802.3at will not support these models.
Inputs (×4)
5 V, 4700 ohms, pull up
Outputs (×2)
Relay output, 120 V AC/
30 V DC, 3 A MAX
Note
Use alarm outputs for SELV
circuits only.
Definition
Pin
Definition
Alarm Out NO 2
9
Alarm In 4
Alarm Out NC 2
10
Alarm In 3
Alarm Out COM 2
11
Alarm In 2
GND
12
Alarm In 1
PoE Requirement
PoE+ (30 W)
PoE++ (60 W)
Advertisement
