Page 1
24686G-ES (rev.0) Safety and Operation Manual Manual de Seguridad y Operación HR3806 Series: DZ - Engine type: Kubota V1505-E Product codes: LHAD003 WARNING: If incorrectly used this machine can cause severe injury. Those who use and maintain this machine should be...
INTRODUCTION RANSOMES HR3806 Series: DZ SAFETY AND OPERATORS MANUAL 2.1 IMPORTANT IMPORTANT: This is a precision machine and the service obtained from it depends on the way it is operated and maintained. This SAFETY AND OPERATORS MANUAL should be regarded as part of the machine. Suppliers of both new and second-hand machines are advised to retain documentary evidence that this manual was provided with the machine.
SAFETY INSTRUCTIONS RANSOMES HR3806 Series: DZ SAFETY AND OPERATORS MANUAL • Remember that some people are deaf or This safety symbol indicates important safety blind and that children and animals can be messages in this manual. When you see this unpredictable.
RANSOMES HR3806 Series: DZ SAFETY INSTRUCTIONS SAFETY AND OPERATORS MANUAL • Do not dismantle the machine without LEAVING THE DRIVING POSITION releasing or restraining forces which can • Park the machine on level ground. cause parts to move suddenly. •...
Page 7
SAFETY INSTRUCTIONS RANSOMES HR3806 Series: DZ SAFETY AND OPERATORS MANUAL DANGER - Indicates an imminently hazardous IMPORTANT: Transport speed is for highway situation which, if not avoided, WILL result in death use only. Never select transport speed on or serious injury.
SPECIFICATIONS RANSOMES HR3806 Series: DZ SAFETY AND OPERATORS MANUAL VIBRATION LEVEL The machine was tested for whole body and hand/ arm vibration levels. The operator was seated in the normal operating position with both hands on the steering mechanism. The engine was running and the cutting device was rotating with the machine stationary.
SPECIFICATIONS RANSOMES HR3806 Series: DZ SAFETY AND OPERATORS MANUAL SLOPES DO NOT USE ON SLOPES GREATER THAN 15° The slope 15° was calculated using static stability measurements according to the requirements of EN 836. RECOMMENDED LUBRICANTS Engine oil: Should be to MIL-L-2104C or to A.P.I.
Make & Type • Nom & Type • Merk & Type • Marke und Typ • Marca e tipo • Fabrikat og type • Fabrikat & typ • Malli ja tyyppi • Marca y Tipo • Marca & Tipo ....Ransomes HR3806 Category •...
Page 12
SPECIFICATIONS RANSOMES HR3806 Series: DZ SAFETY AND OPERATORS MANUAL Conformity Assessment Procedure • Procédure de conformité•évaluation • Conformiteitsbeoordelingsprocedur • Verfahren zur Beurteilung der Konformität • Procedura di valutazione conformità • Procedure for overensstemmelsesvurdering • Procedur för utvärderande av uppfyllande • Yhdenmukaisuuden arviointiproseduuri • Procedimiento de evaluación de conformidad • Processo de avaliação de conformidade Annex VI, Part 1•...
RANSOMES HR3806 Series: DZ DECALS SAFETY AND OPERATORS MANUAL SAFETY DECALS A903491 Read Operator's Manual. A903489 Keep a Safe Distance from the Machine. A903492 Stay Clear of Hot Surfaces. A903488 Do Not Open or Remove Safety Shields While the Engine is Running.
CONTROLS RANSOMES HR3806 Series: DZ SAFETY AND OPERATORS MANUAL STARTER KEY SWITCH The starter key (A) should be turned clockwise to the 'pre-heat' (No. 2) position to heat the glowplugs when the green warning lamp goes out, on warning lamp display module, turn the starter key clockwise to the 'start' (No.
CONTROLS RANSOMES HR3806 Series: DZ SAFETY AND OPERATORS MANUAL PARKING BRAKE The parking brake (B) is engaged when the lever is moved toward the operator. The brake is fitted with a micro switch that senses brake position. The brake must be applied to start the machine, and when stopping and leaving the seat.
CONTROLS RANSOMES HR3806 Series: DZ SAFETY AND OPERATORS MANUAL HYDRAULIC LIFT LEVERS The cutting unit can be raised and lowered by control lever (A) situated on the right hand side of the operators seat and can be operated as follows:...
CONTROLS RANSOMES HR3806 Series: DZ SAFETY AND OPERATORS MANUAL 6.10 INSTRUMENT PANEL ENGINE PREHEAT INDICATOR LAMP Colour green, on when the ignition switch is turned clockwise to the pre-heat position. Once the lamp goes out the engine can be started.
CONTROLS RANSOMES HR3806 Series: DZ SAFETY AND OPERATORS MANUAL 6.11 HOURMETER Located on the left hand side of the steering tower, above the parking brake. (A) Records engine running hours. 6.12 HORN The horn is an audible alarm for the following...
OPERATION RANSOMES HR3806 Series: DZ SAFETY AND OPERATORS MANUAL 7.1 DAILY INSPECTION CAUTION The daily inspection should be performed only when the engine is off and all fluids are cold. Lower implements to the ground, engage parking brake, stop engine and remove ignition key.
OPERATION RANSOMES HR3806 Series: DZ SAFETY AND OPERATORS MANUAL OPERATOR PRESENCE AND SAFETY INTERLOCK SYSTEM The operator presence & safety interlock system prevents the engine from starting unless the parking brake is engaged, the mowing device is off and the operator is in the seat. The system also stops the engine if the operator leaves the seat with the mowing device engaged or the park brake not applied or the emergency brake valve lever is operated.
OPERATION RANSOMES HR3806 Series: DZ SAFETY AND OPERATORS MANUAL OPERATING PROCEDURE CAUTION To help prevent injury, always wear safety glasses, leather work shoes or boots, a hard hat and ear protection. Under no circumstances should the engine be started without the operator seated on the tractor.
OPERATION RANSOMES HR3806 Series: DZ SAFETY AND OPERATORS MANUAL WARNING DO NOT USE ON SLOPES GREATER THAN 15° Slow down and use extra care on hillsides. Read Section 3.7. Use caution when operating near drop off points. Never use your hands to clean cutting units. Use a brush to remove grass clippings from blades.
OPERATION RANSOMES HR3806 Series: DZ SAFETY AND OPERATORS MANUAL MOWING Lower the decks with the cutting unit lift control. Ensure speed limiter is in mow position Engage the cutting mechanism by pushing on the lower half of cutting unit switch and operating the floor mounted switch.
ADJUSTMENTS RANSOMES HR3806 Series: DZ SAFETY AND OPERATORS MANUAL SEAT (GS85/90) The seat can be adjusted for operator's weight and leg reach to provide a comfortable position for operating the machine. ADJUSTMENT FOR OPERATOR WEIGHT To Adjust: The position of the adjusting knob (A) is on the front of the seat, in the centre below the seat cushion.
ADJUSTMENTS RANSOMES HR3806 Series: DZ SAFETY AND OPERATORS MANUAL HEIGHT OF CUT ADJUSTMENT The cutting height is determined by the position of the blades in relation to the caster wheels. Changes to this height are made at (4) points and can be made in any order.
MAINTENANCE RANSOMES HR3806 Series: DZ SAFETY AND OPERATORS MANUAL 9.1 LUBRICATION AND MAINTENANCE CHART & t l i t l i & t l i t l i & t l i t l i & & & t t i...
Page 27
MAINTENANCE RANSOMES HR3806 Series: DZ SAFETY AND OPERATORS MANUAL Lubricate every 50 working hours at arrows r t i e t l r t i l l e e t l r t i F - I GB-25...
MAINTENANCE RANSOMES HR3806 Series: DZ SAFETY AND OPERATORS MANUAL DAILY CHECKS (Every 8 working hours) Oil Level. Check level of oil in sump. Remove dipstick (B) wipe and replace and check that oil is up to the maximum mark. Top up if necessary (A). It is important that this test is carried out with the engine cold and the vehicle parked on level ground.
Page 29
MAINTENANCE RANSOMES HR3806 Series: DZ SAFETY AND OPERATORS MANUAL Cooling System. Check Bug Screen (F) Radiator & Oil cooler are all free from dust /debris and there is an uninterrupted air flow to the engine. The screen should be fitted with the mesh facing the front of the machine.
GUARANTEE / SALES & SERVICE RANSOMES HR3806 Series: DZ SAFETY AND OPERATORS MANUAL GUARANTEE We GUARANTEE that should any defect in workmanship or material occur in the goods within TWO YEARS or two thousand hours (on models equipped with hour meters), or whichever occurs first.
Page 31
INDICE RANSOMES HR3806 Serie: DZ MANUAL DE SEGURIDAD Y OPERACION INDICE PAGINA INTRODUCCION IMPORTANTE ......................2 IDENTIFICACION DEL PRODUCTO ................2 INSTRUCCIONES DE SEGURIDAD INSTRUCCIONES DE OPERACION ................3 SEÑALES DE SEGURIDAD ..................3 ENCENDIDO DEL MOTOR ..................3 CONDUCCION DE LA MAQUINA ................3 TRANSPORTE ......................
INTRODUCCION RANSOMES HR3806 Serie: DZ MANUAL DE SEGURIDAD Y OPERACION IMPORTANTE IMPORTANTE: Esta máquina es de precisión y el servicio obtenido depende de la forma como se opere y mantenga. Este MANUAL DE SEGURIDAD Y OPERACION deberá formar parte de la máquina. Los proveedores de máquinas nuevas y de segunda mano deberán guardar la evidencia documentaria de que este manual se ha...
INSTRUCCIONES DE SEGURIDAD RANSOMES HR3806 Serie: DZ MANUAL DE SEGURIDAD Y OPERACION • Se deberán observar en todo momento las normas del código de circulación por Este símbolo de seguridad indica la inclusión de carretera, tanto si se circula por una como si mensajes importantes de seguridad en este manual.
RANSOMES HR3806 Serie: DZ INSTRUCCIONES DE SEGURIDAD MANUAL DE SEGURIDAD Y OPERACION ABANDONO DE LA POSICION DE • Lea todas las instrucciones de CONDUCCION mantenimiento pertinentes. • Sólo se deberán utilizar las piezas de • Aparque la máquina en terreno llano.
Page 35
INSTRUCCIONES DE SEGURIDAD RANSOMES HR3806 Serie: DZ MANUAL DE SEGURIDAD Y OPERACION • Si es necesario vaciar el depósito de • NO FUME cuando se realice un servicio en combustible, esto se deberá hacer al aire las baterías y mantenga alejadas las llamas libre.
RANSOMES HR3806 Serie: DZ ESPECIFICACIONES MANUAL DE SEGURIDAD Y OPERACION ESPECIFICACIONES DEL MOTOR DIMENSIONES Tipo: Kubota 28KW a 3000 rpm, Anchura de corte: Motor diesel de 4 cilindros 1,52 metros vertical en línea, 4 recorridos, 1,60 metros refrigerado por agua, 1498 cc 1,80 metros con encendido eléctrico de 12V.
ESPECIFICACIONES RANSOMES HR3806 Serie: DZ MANUAL DE SEGURIDAD Y OPERACION NIVEL DE VIBRACION La máquina ha sido probada en cuanto a niveles de vibración en todo el cuerpo, mano y brazo. El operario estaba sentado en la posición normal de operación con ambas manos sobre el mecanismo...
ESPECIFICACIONES RANSOMES HR3806 Serie: DZ MANUAL DE SEGURIDAD Y OPERACION 4.5 PENDIENTES NO UTILIZAR EN PENDIENTES MAYORES DE 15º La pendiente de 15º se ha calculado usando medidas de estabilidad estática conforme a la normativa EN 836. LUBRICANTES RECOMENDADOS Aceite para...
Make & Type • Nom & Type • Merk & Type • Marke und Typ • Marca e tipo • Fabrikat og type • Fabrikat & typ • Malli ja tyyppi • Marca y Tipo • Marca & Tipo ....Ransomes HR3806 Category •...
Page 40
ESPECIFICACIONES RANSOMES HR3806 Serie: DZ MANUAL DE SEGURIDAD Y OPERACION Conformity Assessment Procedure • Procédure de conformité•évaluation • Conformiteitsbeoordelingsprocedur • Verfahren zur Beurteilung der Konformität • Procedura di valutazione conformità • Procedure for overensstemmelsesvurdering • Procedur för utvärderande av uppfyllande • Yhdenmukaisuuden arviointiproseduuri • Procedimiento de evaluación de conformidad • Processo de avaliação de conformidade Annex VI, Part 1•...
RANSOMES HR3806 Serie: DZ ADHESIVOS MANUAL DE SEGURIDAD Y OPERACION ADHESIVOS DE SEGURIDAD A903491 Lea el Manual del Operador. A903489 Manténgase a una distancia segura de la máquina. A903492 Manténgase alejado de superficies calientes. A903488 No abra ni quite protectores de seguridad con el motor funcionando.
CONTROLES RANSOMES HR3806 Serie: DZ MANUAL DE SEGURIDAD Y OPERACION LLAVE DEL MOTOR DE ARRANQUE La llave del motor de arranque (A) se debe girar a la derecha a la posición “pre heat” (pre calentamiento) (Nº2) para calentar las bujías incandescentes, cuando se apaga la luz de advertencia en el módulo de la...
CONTROLES RANSOMES HR3806 Serie: DZ MANUAL DE SEGURIDAD Y OPERACION FRENO DE ESTACIONAMIENTO El freno de estacionamiento (B) se engrana cuando la palanca se mueve hacia el operador. El freno lleva un micro interruptor que detecta la posición del freno. Se debe poner el freno para arrancar la máquina, al parar...
CONTROLES RANSOMES HR3806 Serie: DZ MANUAL DE SEGURIDAD Y OPERACION PALANCAS DE ELEVACION HIDRAULICA La unidad de corte puede levantarse y bajarse con la palanca de control (A) situada a la derecha del asiento del operador y puede activarse del...
CONTROLES RANSOMES HR3806 Serie: DZ MANUAL DE SEGURIDAD Y OPERACION 6.10 PANEL DE INSTRUMENTOS LUZ INDICADORA DE PRECALENTAMIENTO DEL MOTOR Color verde, se enciende cuando se gira la llave de contacto a la derecha a la posición de pre calentamiento.
CONTROLES RANSOMES HR3806 Serie: DZ MANUAL DE SEGURIDAD Y OPERACION 6.11 CONTADOR HORARIO Situado a la izquierda de la columna de dirección, encima del freno de estacionamiento (A). Registra las horas de funcionamiento del motor. 6.12 CLAXON El claxon es una alarma sonora para las siguientes situaciones: a) El claxon (A) suena contínuamente: esto indica...
OPERACION RANSOMES HR3806 Serie: DZ MANUAL DE SEGURIDAD Y OPERACION INSPECCION DIARIA PRECAUCION La inspección diaria sólo debe realizarse con el motor apagado y con todos los líquidos fríos. Baje las unidades al suelo, ponga el freno de estacionamiento, apague el motor y quite la llave de encendido.
OPERACION RANSOMES HR3806 Serie: DZ MANUAL DE SEGURIDAD Y OPERACION SISTEMA DE CONTROL DE PRESENCIA DEL OPERARIO E INTERBLOQUEO DE SEGURIDAD Este sistema impide poner en marcha el motor a menos que se haya soltado la lengüeta de punto muerto y se haya apagado el dispositivo de segado. También para el motor si el operario abandona el asiento con el dispositivo de segado encendido o la lengüeta de punto muerto pisada.
OPERACION RANSOMES HR3806 Serie: DZ MANUAL DE SEGURIDAD Y OPERACION PROCEDIMIENTO DE OPERACION PRECAUCION Lleve siempre gafas de seguridad, zapatos o botas de trabajo fabricados de cuero, un casco y protectores de oidos para no lesionarse. El motor no debe arrancarse bajo ninguna circunstancia si el operario no está sentado en el tractor.
OPERACION RANSOMES HR3806 Serie: DZ MANUAL DE SEGURIDAD Y OPERACION ADVERTENCIA NO UTILIZAR EN PENDIENTES MAYORES DE 15° Desacelere y despliegue mayor precaución al trabajar en cuestas. Lea la Sección 3.7. Tenga precaución cuando trabaje cerca de zonas en las que se bajen pasajeros.
OPERACION RANSOMES HR3806 Serie: DZ MANUAL DE SEGURIDAD Y OPERACION SEGADO Bajar las cubiertas con el control de elevación de la unidad de corte. Comprobar que el limitador de velocidad está en la posición de segado. Engranar el mecanismo de corte...
AJUSTES RANSOMES HR3806 Serie: DZ MANUAL DE SEGURIDAD Y OPERACION ASIENTO (GS85/90) El asiento se puede ajustar al peso y longitud de pierna del operario para ofrecer una posición cómoda para la operación de la máquina. 1 AJUSTE AL PESO DEL OPERARIO Para ajustar: La posición del botón de ajuste (A) está...
AJUSTES RANSOMES HR3806 Serie: DZ MANUAL DE SEGURIDAD Y OPERACION AJUSTE DE LA ALTURA DE CORTE La altura de corte se determina por la posición de las cuchillas en relación con las ruedas direccionales. Los cambios a esta altura se realizan en 4 puntos y en cualquier orden.
MANTENIMIENTO RANSOMES HR3806 Serie: DZ MANUAL DE SEGURIDAD Y OPERACION 9.1 CUADRO DE LUBRICACION Y MANTENIMIENTO e t i t l i f e t i ó i a l i e t i q í l á r c i l ó...
Page 55
MANTENIMIENTO RANSOMES HR3806 Serie: DZ MANUAL DE SEGURIDAD Y OPERACION Lubricar cada 50 horas de funcionamiento en los lugares indicados por las flechas r t i l r t l r t i l l l e l l e...
MANTENIMIENTO RANSOMES HR3806 Serie: DZ MANUAL DE SEGURIDAD Y OPERACION REVISIONES DIARIAS (Cada 8 horas de funcionamiento) Nivel de aceite Revisar el nivel de aceite en el cárter. Sacar la varilla (B) limpiar e introducir de nuevo y revisar si el aceite está...
Page 57
MANTENIMIENTO RANSOMES HR3806 Serie: DZ MANUAL DE SEGURIDAD Y OPERACION Sistema de refrigeración Asegurarse de que la pantalla protectora (F) y el refrigerador del radiador y de aceite estén limpios de polvo/suciedad y de que haya un flujo ininterrumpido de aire al motor. La pantalla debe montarse con la malla mirando a la parte delantera de la máquina.
GARANTIA / VENTAS Y SERVICIO RANSOMES HR3806 Serie: DZ MANUAL DE SEGURIDAD Y OPERACION GARANTIA GARANTIZAMOS que en el supuesto de que surgiera algún defecto de mano de obra o material en la mercancía dentro del plazo de DOS AÑOS o 2000 horas de funcionamiento (en modelos equipados con contadores horarios), o lo que antes suceda, siendo una excepción a esta...
Page 60
World Class Quality, Performance and Support Equipment from Ransomes Jacobsen Limited is built to exacting standards ensured by ISO 9001 registration at all our manufacturing locations. A worldwide dealer network and factory-trained technicians backed by Ransomes Jacobsen Parts Xpress provide reliable, high-quality product support.