Other Audio Problems - Pioneer Elite SC-89 Operating Instructions Manual

13
Symptom Remedy
No sound from surround back Check that the surround back speakers are set to LARGE or SMALL, and the surround
speakers. speakers are not set to NO (see
Check the speaker connections (see
one surround back speaker is connected, make sure it's connected to the left channel
speaker terminal.
When Dolby Surround is selected, audio is not output from the surround back speaker
when it is the only one connected (set).
No sound from front height or front Check that the front height or front wide speakers are set to LARGE or SMALL, and the
wide speakers. surround speakers are not set to NO (see
When Speaker System is set to 7.2.2ch TMd/FW and SP: TMd ON is selected with the
OUT P. button, no sound will be output from the front wide speakers. Select SP: FW ON
or SP: TMd/FW ON (see
When Speaker System is set to 7.2.2ch TMd/FH and SP: TMd ON is selected with the
OUT P. button, no sound will be output from the front height speakers. Select SP: FH ON
or SP: TMd/FH ON (see
Check the speaker connections (see
When Speaker System is set to 7.2.2ch TMd/FW and Dolby Surround is selected,
audio is not output from the front wide speakers.
No sound from subwoofer. Check that the subwoofer is connected properly, switched on and the volume turned up.
If your subwoofer has a sleep function, make sure it is switched off.
Make sure that the Subwoofer setting is YES or PLUS (see
The crossover frequency may be set too low; try setting it higher to match the characteris-
tics of your other speakers (see
If there is very little low frequency information in the source material, change your
speaker settings to Front: SMALL / Subwoofer: YES, or Front: LARGE / Subwoofer: PLUS
(see Speaker Setting
Check that the LFE channel is not set to OFF, or to a very quiet setting (see
Audio options on
Check the speaker level settings (see
No sound from the speakers. Check the AMP setting. Set it to ON when you want to output sound from all the speakers
(Setting the Audio options
No sound from one speaker. Check the speaker connection (see
Check the speaker level settings (see
Check that the speaker hasn't been set to NO (see
The channel may not be recorded in the source. By using one of the advanced effect
listening modes, you may be able to create the missing channel (see
types of playback using the listening modes
Sound is produced from analog Check that the input signal type is set to DIGITAL (see
components, but not from digital 67 ).
ones (DVD, LD, CD, etc.).
Make sure that the digital input is assigned correctly for the input jack the component is
connected to (see
Check the digital output settings on the source component.
If the source component has a digital volume control, make sure this is not turned down.
No sound is output or a noise is out- Check that your BD or DVD player is compatible with Dolby Digital/DTS discs.
put when Dolby Digital/DTS software
Check the digital output settings or the HDMI audio output settings of your BD or DVD
is played back.
player. Make sure that the DTS signal output is set to On.
If the source component has a digital volume control, make sure this is not turned down.
Speaker Setting on page 107 ).
Connecting the speakers on page 25 ). If only
Speaker Setting on page 107 ).
Switching the speaker terminals on page 85 ).
Switching the speaker terminals on page 85 ).
Connecting the speakers on page 25 ).
Speaker Setting
Speaker Setting on page 107 ).
on page 107 ).
page 81 ).
Channel Level on page 108 ).
on page 81 ).
Connecting the speakers on page 25 ).
Channel Level on page 108 ).
Speaker Setting on page 107
Enjoying various
on page 65 ).
Choosing the input signal
The Input Setup menu on page 52 ).
Symptom
No sound when using the
HOME MENU.

Other audio problems

Symptom
Speaker switching sound (clicking
sound) is heard from receiver during
playback.
Broadcast stations cannot be
selected automatically, or there is
considerable noise in radio broad-
casts.
on page 107 ).
Noise is output when scanning a
DTS CD.
When playing a DTS format LD there
is audible noise on the soundtrack.
Setting the
Can't record audio.
Subwoofer output is very low.
Everything seems to be set up cor-
rectly, but the playback sound is odd.
).
The Phase Control feature doesn't
seem to have an audible effect.
on page
Full Band Phase Control cannot be
selected.
Noise or hum can be heard even
when there is no sound being input.
117
Remedy
If the HDMI input function is selected, sound is muted until exiting the HOME MENU.
Remedy
Since ECO MODE 1 and ECO MODE 2 reduce the power consumption, the speakers
are switched in function of the number of input channels. Because of this, a speaker
switching sound (clicking sound) may be produced when the number of input channels
is switched. If this bothers you, switch to a different listening mode.
Depending on the listening mode, the front height (or front wide) and surround back
speakers may switch automatically in function of changes in the input audio. A speaker
switching sound (clicking sound) will be heard from the receiver at this time. If this sound
bothers you, we recommend to change the speaker terminal option (see
speaker terminals on page 85 ).
Fully extend the FM wire antenna, adjust the position for best reception and secure to a
wall, etc.
Use an outdoor antenna for better reception (see page 40
Adjust the position and direction of the AM antenna.
Noise may be caused by interference from other equipment, such as a fluorescent light,
motor, etc. Switch off or move the other equipment, or move the AM antenna.
This is not a malfunction of the receiver. The scan function of your player alters the digital
information, making it unreadable, resulting in noise being output. Lower the volume
when scanning.
Make sure that the input signal type is set to DIGITAL (see
page 67 ).
You can only make a digital recording from a digital source, and an analog recording
from an analog source.
For digital sources, make sure that what you're recording isn't copy protected.
To route more signal to the subwoofer, set it to PLUS or set the front speakers to SMALL
(see Speaker Setting on page 107 ).
The speakers may be out of phase. Check that the positive/negative speaker terminals on
the receiver are matched with the corresponding terminals on the speakers (see
necting the speakers on page 25 ).
If applicable, check that the lowpass filter switch on your subwoofer is off, or the lowpass
cutoff is set to the highest frequency setting. If there is a PHASE setting on your sub-
woofer, set it to 0º (or depending on the subwoofer, the setting where you think it has the
best overall effect on the sound).
Make sure the speaker distance setting is correct for all speakers (see
on page 108 ).
Perform Full Auto MCACC measurements (see Automatically conducting optimum
sound tuning (Full Auto MCACC) on page 51 ). Full Band Phase Control automatically
turns on once measurements are completed.
Check that personal computers or other digital components connected to the same
power source are not causing interference.
FAQ
Switching the
).
Choosing the input signal on
Con-
Speaker Distance