Speakers Set - Yamaha RX-V1200 Service Manual

RX-V1200/RX-V1200RDS/HTR-5490/RX-V2200

8. SPEAKERS SET

The input signal is automatically identified in the order of dts → DOLBY DIGITAL → AAC→ PCM → Analog.
There are seven sub-menu items as follows. The signals output from the DSP block are the same as 1. YSS938: YSS
0dB.
MAIN: SMALL 0dB
LFE: BASS:MAIN
REAR L/R: MUTE
The analog switch settings for each sub-menu are as shown in the table below.
Sub-menu
1 MAIN: SMALL 0dB
2 MAIN: LARGE -10dB
3 CENTER: NONE
4 LFE/BASS: MAIN
5 FRONT MIX: 5CH
6 REAR CENTER: MUTE
7 REAR L/R: MUTE
LARGE: This mode is used with a speaker with high bass reproduction performance (a large unit). Full bandwidth
signals are output.
SMALL: This mode is used with a speaker with low bass reproduction performance (a small unit). The signals of 90Hz
or less are mixed into the channel specified by LFE/BASS.
NONE: This mode is used with no center speaker. The center content is reduced by 3dB and distributed to MAIN L/R.
Reference data (PRE OUT)
INPUT: DVD ANALOG (Both ch)
VOLUME: -10 dB
Sub-menu
1 MAIN: SMALL 0dB
2 MAIN: LARGE -10dB
3 CENTER: NONE
4 LFE/BASS: MAIN
5 FRONT MIX: 5CH
6 REAR CENTER: MUTE
7 REAR L/R: MUTE
29
MAIN: LARGE -10dB
Front Mix: 5ch
CENTER SP REAR SP MAIN SP MAIN LEVEL LFE/BASS
LARGE LARGE SMALL
LARGE LARGE LARGE
NONE LARGE LARGE
SMALL SMALL LARGE
LARGE LARGE LARGE
LARGE LARGE LARGE
LARGE LARGE LARGE
Condition MAIN L/R CENTER REAR C
1kHz/90Hz, -20 dBV -5.5/-8.5 dBV -5.5 dBV
1kHz, -20 dBV -15.5 dBV -5.5 dBV
1kHz, -20 dBV -9.0 dBV
50Hz, -20 dBV -4.0 dBV -8.5 dBV (90Hz) -5.5 dBV
1kHz, -20 dBV -11.5 dBV -5.5 dBV
1kHz, -20 dBV -5.5 dBV
1kHz, -20 dBV -5.5 dBV
CENTER: NONE
REAR CENTER: MUTE
0dB SWFR
-10dB BOTH
0dB BOTH
0dB MAIN
0dB BOTH
0dB BOTH
0dB BOTH
SWFR
-5.5 dBV -2.5 dBV
-5.5 dBV -2.5 dBV
- ∞
-5.5 dBV -2.5 dBV
- ∞
-5.5 dBV -2.5 dBV
- ∞
-5.5 dBV -2.5 dBV
-5.5 dBV -5.5 dBV -2.5 dBV
RL/RR
-5.5 dBV
-5.5 dBV
-5.5 dBV
-8.5 dBV (90Hz)
-5.5 dBV
-5.5 dBV
- ∞