Adjusting The Level; Setting The Source Volume Level; Adjusting The Crossover Settings (X-Over); Selecting The Cut-Off Frequency (Frequency) - Alpine CDE-193BT Operating Instructions Manual

Adjusting the Level

Setting contents:
−7 to +7 (Initial setting: ±0)
Notes
• BAND2 and BAND8 are the same as the Bass and Treble controls.
Their Level adjustment can also be controlled by pressing YSETUP
and selecting Bass Level or Treble Level. Refer to "Adjusting Subwoofer
Level/Bass Level/Treble Level/Balance (Between Left and Right)/Fader
(Between Front and Rear)/Defeat" on page 16.
• Settings exceeding the frequency of adjacent bands are not available.
• While adjusting the 9BAND P-EQ, you should consider the frequency
response of the connected speakers.
• The 9-Band, Parametric EQ is used to customize the EQ PRESETS
settings.

Setting the Source Volume Level

The output level of each source is individually adjustable. For example, if
the TUNER level sounds lower than CD, its output can be adjusted
without affecting the other sources.
 Setting item: SOURCE VOL
 Further setting items: TUNER / DISC
BT AUDIO / AUX
Setting contents:
−14 dB ~ +14 dB (Initial setting: ±0)
* Only for CDE-193BT.
Adjusting the Crossover Settings
(X-OVER)
Before performing the following procedures, refer to "About the
Crossover" on page 22.
 Setting item: X-OVER
1
Turn the Rotary encoder to select the channel, and then
press ENTER.
 2WAY System
FRONT (HPF)  REAR (HPF)  SUBW LPF
 3WAY System
LOW (LPF)  MID LOW (HPF)  MID HIGH (LPF) 
HIGH (HPF)
2
Turn the Rotary encoder to select the desired item, and
then press ENTER.

Selecting the Cut-Off Frequency (FREQUENCY)

 2WAY System
Setting contents:
20 / 25 / 31.5 / 40 / 50 / 63 / 80 (Initial setting) / 100 / 125 /
160 / 200 (Hz)
 3WAY System
Setting contents:
*
LOW/MID LOW :
20 / 25 / 31.5 / 40 / 50 / 63 / 80 / 100 / 125 / 160 / 200 / 250 / 315 /
400 / 500 (Initial setting) / 630 / 800 (Hz)
*
MID HIGH :
20 / 25 / 31.5 / 40 / 50 / 63 / 80 / 100 / 125 / 160 / 200 / 250 / 315 /
400 / 500 / 630 / 800 / 1 k / 1.2 k / 1.6 k / 2 k / 2.5 k / 3.2 k / 4 k /
5 k (Initial setting) / 6.3 k / 8 k / 10 k / 12.5 k / 16 k / 20 k (Hz)
18
-EN
*
/ USB / iPod /
HIGH:
1 k / 1.2 k / 1.6 k / 2 k /2.5 k / 3.2 k / 4 k / 5 k (Initial setting) / 6.3 k /
8 k / 10 k / 12.5 k / 16 k / 20 k (Hz)
* The cut-off Frequency setting result for MID LOW cannot be
adjusted greater than MID HIGH.

Adjusting the Slope (SLOPE)

Setting contents:
* *
FLAT / 6 / 12 / 18 / 24 (dB/oct.)
* Not available when "MID HIGH" is selected in 3WAY System.
Note
• The initial setting for 2WAY is FLAT. 3WAY is 12.

Adjusting the Level (LEVEL)

Setting contents:
−12 to 0 (dB) (Initial setting: 0)
3
Repeat steps 1 to 2 to make adjustment to the other
channels.
Notes
• The level setting results for MID LOW and MID HIGH in 3WAY
system are linkage.
• The adjustable cross-over range might be different between Alpine
TuneIt App and the unit.

Turning Subwoofer ON/OFF

When the subwoofer is on, you can adjust the subwoofer output level
(refer to "Adjusting Subwoofer Level/Bass Level/Treble Level/Balance
(Between Left and Right)/Fader (Between Front and Rear)/Defeat" on
page 16).
 Setting item: SUBWOOFER
Setting contents:
SUBW ON (Initial setting) / SUBW OFF
SUBW ON:
The subwoofer signal is output from the Subwoofer RCA
Connectors (refer to "Connections" on page 48).
SUBW OFF:
No subwoofer signal is output from the Subwoofer RCA
Connectors (refer to "Connections" on page 48).

Setting the Subwoofer Phase

The subwoofer output phase is toggeled between SUBWOOFER
NORMAL (0°) or SUBWOOFER REVERSE (180°). Depending on the
installation location of your subwoofer, one of these settings may sound
better than the other.
 Setting item: SUBW PHASE
Setting contents:
NORMAL (Initial setting) / REVERSE

Setting the Subwoofer System

When the subwoofer is on, you can select either SUBW SYS 1 or SUBW
SYS 2 for the desired subwoofer effect.
 Setting item: SUBW SYS
Setting contents:
SUBW SYS 1 / SUBW SYS 2 (Initial setting)
SUBW SYS 1:
Subwoofer level changes according to the main volume setting.