Command Reference Program - Panasonic KX-P1131 Operating Instructions Manual

Using the Software
Command Reference Program
The Command Reference program allows you to access a detailed explanation of each software command on the
screen. Each displayed explanation can be printed out if required.
Note:
• You can print the Character Set Tables. On the SELECT COMMAND screen, press
©.
Then select your
desired table and press
lful!riJ.
• If 7 bit is selected for Data Length, you cannot print the command lists and character set tables.
• There is a list of Proportional Spacing Tables after the software commands lists. If you want to see a
proportional spacing table, select your desired table and press
I
Enter) .
l _ _ _
~
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ . _ _
To recall the programs, follow the steps below.
<DOS> <Windows 3.1> <Windows 95 and
1" At your C:\prompt, 1 Select
I
Run
I
from the File
Windows 98>
Cpe Cj PI 131 and press
menu.
1 Click
I
Start
I ,
point to
Enter.
"Run ... " and click.
2 Type C:IPI 13IICMDREF
2 Type C:1P1I31ICMDREF
2 Type CMDREF and press
and press
I
Enter) .
and press
I
Enter
I
CEil@.
(or click 10K
I).
(or click 10K
I).
*
If you changed the directory when installing utilities for DOS, select your changed directory and press
I
Enter
I.
i
Note:' - -. -_.. --- --." - .. - - ....... - .-. --.-_.-.... -_. -- -.-------
• If you want to run the Command Referece program using the Setup Disk, follow the steps below.
1. Insert your DOS Uti lites & Printer Driver for Windows® 3.1, 95 & 98 disk into drive A (or 8).
<DOS>
2. 0 (ype
I'
(or B:) and press
Enter.
e
(ype
Cj DOS
and press
Enter.
<Windows 3.1 >
2. 0
Select
I
Run
I
from the File
menu.
e
Type A:\DOs\CMDREF
(or
B:\DOS\CMDREF).
<Windows 95 and Windows 98>
2. 0
Click
I
Start
I ,
pOint to
"Run ... " and click.
e
Type A:\DOs\CMDREF
(or
B:\DOS\CMDREF).
@)
Click OK
(or pre'':'s'='s''''''E=nt'-:e'''r ).
@)
Click
I
OK
I
(or press [Enter)).
I
@)
(ype CiDREF and press
I Enter .
l... _
3
4
5
The first screen is an introduction to
the operation of the Command Reference
program. Please read it through and press
any key to continue. (If your display is
monochrome, press "M" key.)
Select the desired emulation and press
I
Enter) (or click 10K
I).
The commands list will be displayed.
Select the desired command and press
[ Enter) (or click
I
OK
I).
The detailed explanation of the command will be
displayed.
6
Press
(]J
to exit Command Reference.
« Panasonic KX-P1131 command reference utility (xxxxxxxxxx) »
- -SELECT EMULAnON --
EPSON
IBM
[TI/[l)
[Enter]
[E)
: Select emulabon
: Set emutaton
: Exit Command Reference
:::I
!e-
III
:::I
IC
III
:::I
Co
c:
21.
:::I
IC
-
: :T
(I)
"
>< ,
"'C
... ...
Co)
...
CJ)
i
iil
27