Related Manuals for Sony Wega KV-HS38
Summary of Contents for Sony Wega KV-HS38
- Page 1 4-094-607-11 (1) Trinitron Color TV Operating Instructions • Before operating the unit, please read this manual thoroughly and retain it for future reference. KV-HS38 KV-HS34 KV-HS29 M91, M61 © 2003 Sony Corporation...
- Page 2 WARNING • Dangerously high voltages are present inside the TV. • TV operating voltage: 110–240 V AC (KV-HS29/HS34), 220–240 V AC (KV-HS38). • Do not plug in the power cord until you have completed making all other connections; otherwise a minimum leakage current might flow through the antenna and other terminals to ground.
- Page 3 Do not plug in too many appliances to the same Do not place any objects on the TV. power socket. Do not damage the power cord. Pull the power cord out by the plug. Do not pull the power cord itself. Even if your TV is turned off, it is still connected to the AC power source Install the TV on a stable TV stand and floor which (mains) as long as the power cord is plugged in.
- Page 4 Using Your New TV...
-
Page 5: Table Of Contents
Table of Contents WARNING Using Your New TV Getting Started ..................... 6 Step 1 Secure the TV ................6 Step 2 Connect the antenna ..............7 Step 3 Insert the batteries into the remote .......... 8 Step 4 Set up your TV automatically ..........9 Connecting optional components ............ -
Page 6: Using Your New Tv
Using Your New TV Using Your New TV Getting Started Step 1 Secure the TV To prevent the TV from falling, use the supplied screws, clamps and band to secure the TV. 20 mm 3.8 mm screws clamps band Screw the band to the TV stand and to the provided hole at the rear of your TV. -
Page 7: Step 2 Connect The Antenna
Step 2 Connect the antenna If you wish to connect a VCR, see the “Connecting a VCR” diagram on page 8. Rear of TV Antenna cable (not supplied) IEC connector (not supplied) Antenna cable (not supplied) : Signal flow CAUTION Do not connect the power cord until all other connections are complete;... -
Page 8: Step 3 Insert The Batteries Into The Remote
Getting Started (continued) Connect a VCR To play a video tape, press t (see page 17). To 8 (antenna) Antenna cable (not supplied) Rear of TV To antenna (S video input) output S video cable (not supplied) SYNC AUDIO VIDEO (MONO) VIDEO IN To S video... -
Page 9: Step 4 Set Up Your Tv Automatically
Step 4 Set up your TV automatically VIDEO DRC-MF V CENTER MENU HD/DVD PROG Press ! to turn on the TV. INITIAL SETUP The “INITIAL SETUP” LANGUAGE: ENGLISH menu appears, and you can select the on-screen language. Move up or down to select the desired language, then press PIC ROTATION... - Page 10 Getting Started (continued) If the upper and lower bars are not equally positioned to the top and INITIAL SETUP bottom of the screen, START AUTO PROGRAM move up or down to NOW? adjust them, then press The automatic channel presetting menu appears. Move up or down to INITIAL SETUP...
-
Page 11: Connecting Optional Components
Connecting optional components You can connect optional audio/video components, such as a VCR, a DTV (Digital Television) receiver, multi disc player, camcorder, video game, or stereo system. To watch and operate the connected equipment, see pages 17 and 31. Connecting a camcorder/video game equipment using the t (video input) jacks Front of TV Video game... - Page 12 Connecting optional components (continued) Connecting audio/video equipment using the T (monitor output) jacks Antenna cable (not supplied) Rear of TV antenna output Audio system SYNC (MONO) To video audio and audio inputs inputs To T (yellow) Audio cable (monitor -L (MONO) (not supplied) output) (white)
- Page 13 Connecting a DVD player to (component video input) 1 Using an audio cable, connect R and L under 1 or 2 (component video input) on your TV to the LINE OUT, AUDIO R and L output connectors on your DVD player. 2 Using a component video cable, connect Y, P , and P under...
- Page 14 Connecting optional components (continued) Connecting a DVD player to t (video input) Connect t 1, 2, or 3 (video input) / (audio/video) connectors on your TV to LINE OUT on your DVD player. To t 1, 2, or 3 To audio/video output (video input) Audio/Video cable...
- Page 15 Connecting a DTV (digital television) receiver to 1 or 2 (component video input) jacks Rear of TV Component video cable 1 or 2 (not supplied) (Component video input) To component video output Digital TV receiver SYNC To audio output Audio cable (not supplied) L (white) R (red)
-
Page 16: Watching The Tv
Watching the TV VIDEO This section explains various functions and operations used while watching the TV. Most operations can be done using DRC-MF the remote. V CENTER HD/DVD HD/DVD Number buttons JUMP JUMP PROG PROG +/– PROG OPTION RESET 2 +/– 1 indicator Press ! to turn on the TV. - Page 17 To select a TV program quickly (1) Press and hold PROG +/–. (2) Release PROG +/– when the desired program number appears. Note • When you select a TV program quickly, the picture may be disrupted. This does not indicate a malfunction. Additional tasks Press Turn off temporarily...
-
Page 18: Setting The Sleep Timer
Watching the TV (continued) Setting the Wake Up timer Press until the desired WAKE UP TIMER:10M period of time appears. After 10 minutes The Wake Up timer starts immediately after you have set it. WAKE UP TIMER:OFF WAKE UP TIMER:12H00M No Wake Up Timer After 12 hours Select the TV channel or video mode you want to wake up to. -
Page 19: Advanced Operations
Advanced Operations Selecting the picture and sound modes JUMP You can select picture and sound modes PROG and adjust the setting to your preference in the “PERSONAL” option. OPTION RESET Selecting the picture mode Press repeatedly until the desired picture mode DYNAMIC STANDARD is selected. -
Page 20: Viewing Higher Quality Pictures
“GAME MODE” or “TWIN” mode is turned “ON”. The mode is not also available for HD (high-definition) or progressive input signal, or the picture recorded on a “Memory Stick”. The DRC-MF logo ( ) and “DRC-MF” are trademarks of Sony Corporation. Advanced Operations... -
Page 21: Time
Watching two VIDEO programs at the same time DRC-MF V CENTER — “TWIN” With the TWIN pictures feature, you can display a different TV program beside the main picture. HD/DVD JUMP Displaying TWIN pictures Press To return to the normal screen Press The left picture is displayed in full screen. - Page 22 Watching two programs at the same time (continued) Additional tasks Press/Move change a TV program in the right Move up or down (TWIN PROG + or –). picture swap the left and right pictures Press swap sound between the left and Press right pictures.
- Page 23 Selecting a TV program using TWIN You can select your desired TV program directly from the right picture by using (TWIN PROG +/–). Move up or down (TWIN PROG +/–). The TWIN pictures appear on the screen. Move up or down (TWIN PROG +/–) until the desired program appears on the right screen.
-
Page 24: Displaying Multiple Programs
Displaying VIDEO multiple programs DRC-MF PROG V CENTER — “PROGRAM INDEX” INDEX The PROGRAM INDEX feature displays all of the preset TV programs on twelve sub screens for direct selection. HD/DVD JUMP PROG PROG +/– OPTION RESET Press PROG INDEX. Sub screens The first twelve preset programs appear one by... - Page 25 To select the desired program directly from the sub screens 1 Move up, down, left or right to move the frame to the screen of the program you want to watch. 2 Press 3 Press again. • Pressing the number buttons directly displays the program. To return to the normal screen Press PROG INDEX again, or: 1 Select “PROGRAM INDEX”...
-
Page 26: Listening With Surround Sound
Listening with surround sound The surround feature enables you to JUMP enjoy the sound effects of a concert hall or movie theater. PROG OPTION RESET Press repeatedly until you receive the desired SURROUND: TruSurround surround sound. SURROUND: SIMULATED SURROUND: OFF Select listen to the surround sound that spreads out to the rear of a room. -
Page 27: Programs
Enjoying stereo or bilingual VIDEO programs DRC-MF V CENTER You can enjoy stereo sound or bilingual programs of NICAM and A2 (German) stereo systems. When you receive the channel with HD/DVD them, the indicator on the front panel of the TV lights up red. Press A/B repeatedly until you receive the sound you want. - Page 28 Enjoying stereo or bilingual programs (continued) When receiving an A2 (German) program Broadcasting On-screen display (Selected sound) A2 (German) stereo STEREO MONO (Regular sound) (Stereo sound) A2 (German) bilingual MAIN (Main sound) (Sub sound) Receiving area for NICAM and A2 (German) programs System Receiving area NICAM...
-
Page 29: Viewing Teletext
Viewing Teletext VIDEO Some TV stations broadcast an information service called Teletext DRC-MF which allows you to receive various V CENTER information, such as stock market reports and news. HD/DVD Number buttons JUMP (red, green, PROG yellow, blue) PROG +/– OPTION RESET Displaying Teletext... - Page 30 Viewing Teletext (continued) Additional Teletext tasks Do this Press display a Teletext page on the TV Each time you press , the screen changes as picture follows: Teletext t Teletext and TV t TV. Press check the contents of a Teletext service An overview of the Teletext contents, including page numbers, appears on the screen.
-
Page 31: Operating Optional Components
Operating VIDEO optional VIDEO I/1 components DRC-MF V CENTER You can use the supplied remote to operate Sony video equipment such as Beta, 8 mm, VHS or DVD. HD/DVD Number buttons 1-7 JUMP Number button 0 PROG OPTION RESET OPTION... -
Page 32: Operating Video Equipment
Operating optional components (continued) Note • If the equipment does not have a certain function, the corresponding button on the remote will not operate. Operating video equipment Press VIDEO @/1, or while keeping OPTION pressed, press (N) or move (X), down (x), left (.) or right (>) (see the chart below). VIDEO OPTION OPTION... - Page 33 Operating an MDP using the remote Press/Move turn on/off VIDEO I /1 play N while keeping OPTION pressed. stop x while keeping OPTION pressed. pause X while keeping OPTION pressed. Press again to resume normal playback. search the picture forward or >...
-
Page 34: Using A "Memory Stick
“Memory Stick” compatible products. Supported image types This TV’s “Memory Stick” viewer can display only still images that have been recorded on “Memory Stick” media by Sony brand digital still and video cameras. Note •... - Page 35 – Images recorded on digital still cameras and digital video cameras that are not Sony brand – Images recorded using products that are not DCF compliant, including the Sony DCR-TRV900/TRV900E and DSR-PD100/ PD100A/100P/100AP digital video cameras – Images stored on a “Memory Stick” that has a capacity that exceeds 128MB –...
- Page 36 Notes on using a “Memory Stick” • To prevent data loss, make backup of data frequently. In no event will Sony be liable for any loss of data. • Unauthorized recording may be contrary to the provisions of copyright law.
- Page 37 To remove a “Memory Stick” 1 Check that the “Memory Stick” indicator is off. (When the light is on, this indicates that the TV is reading data from the “Memory Stick”). 2 Push the “Memory Stick” gently into the slot, and then release it. The “Memory Stick”...
- Page 38 Using a “Memory Stick” (continued) Displaying the “Memory Stick” menu VIDEO DRC-MF MEMORY STICK V CENTER HD/DVD Insert a “Memory Stick” into the “Memory Stick” slot on the front of the TV (see page 36). Press MEMORY STICK. Memory Stick The “Memory Stick”...
- Page 39 Displaying index pictures You can display twelve thumbnail pictures stored in a “Memory Stick” at one time. You can also select one of them to display in full screen. After displaying the “Memory Stick” menu, move up or Yellow cursor indicates the currently down to select “Index”, then selected picture.
- Page 40 Using a “Memory Stick” (continued) To display one of the index pictures in full screen Move up, down, left or right to move the yellow cursor to the still picture you want to display, then press To return to the “Memory Stick Index” screen, press again.
- Page 41 To end the slide show While the slide show is running, press The screen returns to the “Memory Stick” menu. To change the interval of the slide show You can select the timing to advance pictures among “5 sec.” (factory setting), “10 sec.”, “1 min.”, “5 min.” and “15 min.” 1 After displaying the “Memory Stick”...
- Page 42 Using a “Memory Stick” (continued) To run a slide show one time You can set the slide show not to repeat automatically. 1 After displaying the “Memory Stick” menu, move up or down to select “Setup”, then press 2 Move up or down to select “Slideshow - Repeat”, then press Memory Stick Setup Back...
- Page 43 Rotating a still picture You can rotate a still picture stored in a “Memory Stick” in 90° steps. After displaying the Memory Stick Setup “Memory Stick” menu, Back move up or down to Slideshow - Interval: 5 sec. select “Setup”, then Slideshow - Repeat: On press File Information: On...
-
Page 44: Selecting The Picture And Sound
Adjusting Your Setup (MENU) Introducing the menu system The MENU button lets you open a menu and change the settings of your TV. The following is an overview of the menu system. Return icon Name of the current PICTURE icon menu S E T UP LANGUAGE :... - Page 45 Level 3/Level 4/Function Level 1 Level 2/Level 3 Display still pictures stored in a “Memory Stick”. “MEMORY “MEMORY STICK STICK” MENU” You can also display this menu by pressing MEMORY STICK on the remote. Display multiple still pictures. “Index” Display still pictures in sequence. “Slideshow”...
- Page 46 Introducing the menu system (continued) How to use the menu Press MENU to VIDEO PICTURE display the menu. DRC-MF: DRC1250 PICTURE MODE: DYNAMIC 3D-NR: ON WIDE MODE: OFF DRC-MF GAME MODE: OFF V CENTER Move the button MU L T I P I C T URE joystick ( ) up, TWIN: OFF...
-
Page 47: Changing The "Picture" Setting
Changing the “PICTURE” setting VIDEO The “PICTURE” menu allows you to: DRC-MF adjust the picture setting, view higher V CENTER quality pictures, reduce picture noise, MENU and adjust the picture setting that is suitable for viewing video games. You can also change the size of the picture on HD/DVD the screen when you receive wide mode (16:9) picture signals. - Page 48 Changing the “PICTURE” setting (continued) Select change the size of the picture when receiving wide-mode (16:9) “WIDE MODE” picture signal. Move up or down to select “ON”, then press You can also change to wide-mode picture size by using the button.
- Page 49 Adjusting the “ADJUST” options under “PICTURE MODE” Move up or down to select the desired item (e.g., “COLOR”), then press COLOR Adjust the value according to the following table, then press Move down or left to Move up or right to “PICTURE”...
-
Page 50: Changing The "Sound" Setting
Changing the “SOUND” setting The “SOUND” menu allows you to VIDEO adjust the sound setting and adjust the volume automatically. You can also listen to the sound with surround effect. DRC-MF V CENTER MENU HD/DVD Press MENU. PICTURE DRC-MF: DRC1250 PICTURE MODE: DYNAMIC 3D-NR: ON WIDE MODE: OFF... -
Page 51: Pages 19 And
• For details on the options under the “SOUND MODE” and “SURROUND” modes, see pages 19 and 26, respectively. To return to the normal screen Press MENU. Adjusting the “ADJUST” options under “SOUND MODE” Move up or down to select the desired item (e.g., “BALANCE”), then press BALANCE... -
Page 52: Changing The "Memory Stick" Setting
Changing the “MEMORY STICK” setting VIDEO The “MEMORY STICK” menu allows you to view still pictures recorded by a DRC-MF digital camera and stored in a “Memory V CENTER Stick”. MENU Insert a “Memory Stick” into the “Memory Stick” slot. For details on a “Memory Stick”, see pages 34 to 43. -
Page 53: Setting
Changing the “MULTI PICTURE” VIDEO setting PROG INDEX DRC-MF The “MULTI PICTURE” menu allows V CENTER you to use the TWIN pictures, or PROGRAM INDEX feature. MENU HD/DVD Press MENU. PICTURE DRC-MF: DRC1250 PICTURE MODE: DYNAMIC 3D-NR: ON WIDE MODE: OFF GAME MODE: OFF Move up or down to... -
Page 54: Enjoying Stereo Or Bilingual Changing The "Setup" Setting
Changing the “SETUP” setting VIDEO The “SETUP” menu allows you to adjust the setup of your TV. For example, you DRC-MF can change the menu language, preset V CENTER channels, etc. MENU HD/DVD Number buttons JUMP Press MENU. PICTURE DRC-MF: DRC1250 PICTURE MODE: DYNAMIC 3D-NR: ON WIDE MODE: OFF... - Page 55 Select “PIC POSITION” adjust the position of the picture if it is not aligned with the TV screen. PIC POSITION PIC ROTATION PIC V-POSITION See “Adjusting the alignment of the picture” on page 56. preset channels. “CH PRESET” CH PRESET AUTO PROGRAM MANUAL PROGRAM TV SYS : B/G...
- Page 56 Changing the “SETUP” setting (continued) Adjusting the alignment of the picture The picture may be out of alignment with the TV screen due to the influence of the earth’s magnetic field. You can adjust the position of the picture if it is not aligned. After selecting “PIC POSITION”, move up or...
- Page 57 Presetting channels manually After selecting “CH MANUAL PROGRAM PRESET”, move up or PROG : TV SYS : B/G down to select “MANUAL SENS : HIGH PROGRAM”, then press VHF LOW FINE : AUTO Select the program number to which you MANUAL PROGRAM want to preset a channel.
-
Page 58: Fine" Tuning Feature
Changing the “SETUP” setting (continued) If you are not satisfied with the picture and sound quality, you may be able to improve them by using the MANUAL PROGRAM “FINE” tuning feature. AUTO PROG : 10 MANUAL TV SYS : I (1) Move up or down SENS : HIGH... - Page 59 Skipping unwanted or unused channels (“SKIP”) After performing automatic channel presetting, you can erase unwanted or unused channels. After selecting PROGRAM SETUP “PROGRAM SETUP”, PROG : make sure “PROG” is SKIP : OFF CHILD LOCK : OFF selected, then press Move up or down PROGRAM SETUP...
- Page 60 Changing the “SETUP” setting (continued) Blocking channels (“CHILD LOCK”) After selecting PROGRAM SETUP “PROGRAM SETUP”, PROG : SKIP : OFF make sure “PROG” is CHILD LOCK : OFF selected, then press Move up or down to PROGRAM SETUP select the desired channel PROG : SKIP : OFF (e.g.
-
Page 61: Troubleshooting
Additional Information Troubleshooting If you have any problem while viewing your TV, please check the following troubleshooting guide. If the problem persists, contact your Sony dealer. Possible cause Solutions Symptom Page • Check the antenna cable and Snowy picture • The connection is... - Page 62 – • The antenna direction • Adjust the antenna direction. Contact needs adjustment. a Sony dealer for advice. – • Use of a booster is • Turn off or disconnect the booster if inappropriate. it is in use.
- Page 63 • Adjust the antenna direction. Contact a – • The antenna direction needs adjustment. Sony dealer for advice. The sound switches between stereo and • Press A/B until a better sound is heard. • The broadcast signal monaural has a transmission frequently.
- Page 64 Troubleshooting (continued) Page Possible cause Solutions Symptom • Some shooting Cannot play games which shooting games. involve pointing a light beam at the TV screen with an electronic gun or rifle cannot be used with your TV. For detail, see the instruction manual supplied with the video game...
-
Page 65: Self-Diagnosis Function
Count the number of times the 1 indicator flashes. Press ! (main power) to turn off your TV. Inform your nearest Sony service center about the number of times the 1 indicator flashed. Be sure to note the model name and serial number located on the rear of your TV. -
Page 66: Identifying Parts And Controls
Identifying parts and controls Front and inside the drop-down panel Front panel Inside the drop-down panel L(MONO) AUTO PROG MENU ENTER PROG Button/connector Function Page “Memory Stick” slot Insert a “Memory Stick“ into this slot. “Memory Stick” Flashes when the data is being indicator read from a “Memory Stick”. - Page 67 Rear SYNC (MONO) Connector Function Page Connect to S video output of video equipment. Connect to video/audio outputs of video equipment. Connect to video/audio inputs of audio/video equipment. Connect to component video outputs on a DVD player. Connect to component video outputs on a DVD player.
-
Page 68: Remote Control
Identifying parts and controls (continued) Remote control The names/symbols of buttons on the remote are indicated in different colors to represent the available functions. Button function Label color VIDEO White For general TV operations Green For Teletext operations Yellow For TWIN picture operations DRC-MF Pink For optional components operations... - Page 69 Button Function Page VIDEO ?/1 •Power. •Use with the number buttons to set up the remote. DRC-MF Select DRC-MF mode. VIDEO •Select stereo/bilingual mode. 27 •Enlarge the Teletext display. 30 PROG INDEX Display all preset TV DRC-MF programs. V CENTER •Select, adjust and confirm selected items in the menu.
- Page 70 Additional Information...
- Page 71 Additional Information...
-
Page 72: Specifications
898 × 678 × 581 994 × 755 × 623 Dimensions (w/h/d, mm) Mass (kg) Design and specifications are subject to change without notice. Sony Thai Co., Ltd. 2126 Kromadit Building, New Petchburi Road, Bangkapi, Huaykwang, Bangkok 10320 http://www.sony.net/ Additional Information...