Advertisement
INTRODUCTION
Introduction
Thank you for your purchase of the Thunder Tiger 3D Sukuoi EP. You can make t
easily do any aerobatics and 3D maneuvers, includes Knife Edge, Hovering, Torque Rolls, Corbra...etc.
Made of Anti-Impact EPP material that reduce the crash damage. Very good for those who are interested in
learning 3D-aerobatics or experienced 3D pilots who are looking for a relaxed practicing plane that can be
used both outdoor and indoor.
The
3D Sukuoi EP
is designed for intermediate pilot minded. Before beginning the assembly read
the instructions thoroughly to give an understanding of the sequence of steps and a general awareness of
the recommended assembly procedures. Check the entire contents of your kit against the parts drawing
and photos to make sure that no parts are missing or damaged. This will also help you to become familiar
with each component of your plane. If you find that any of the parts are either missing or damaged, please
contact Thunder Tiger Distributors for Customer Service.
TABLE OF CONTENTS
Introduction.........................................................................................................................2
Parts Drawings........................................................................................................................3
Wing.....................................................................................................................................4
Tail........................................................................................................................................5
Motor...................................................................................................................................6
Landing Gear..........................................................................................................................7
Setup....................................................................................................................................8-10
.............................................................................................................................11
OTHER ITEMS REQUIRED FOR ASSEMBLY
A checklist is provided as below which will make shopping for these items easier.
Brushless Motor: Recommend
OBL29/09-07A motor ( No.2354)
C o n t r o l l e r : A C E B L C 1 2 A
(No. 8026) is a perfect controller
that
controlling
OBL
efficiently.
Battery:
Recommend
the use
of a ACE Power Lipo battery
3S1P 1100mAh(No.2804).
Extension Wire: 2 pieces of
extension wire in length of 9".
Propeller: There is 12" prop. in
the kit, yet it is only for test flight.
Recommended APC 10x4.7 SF
propeller for high performance 3D
aerobatics.
his
proven 3D fun flyer
Radio: A 4-channel radio with
3 micro servos and mini receiver
are required.
motor
Adhesives: You will need the
thick instant (cyanoacrylate)
adhesives.
TOOLS AND SUPPLIES NEEDED
Paper Towel
Hobby Knife
Ruler
Pen, Pencil or Marker
Phillips&Flat Head Screw Drivers
Scissors
Nose Plier
Drill Bit 5/64" (2mm)
2
Open the box and check that you have all the parts as shown below.
AS6647 Fuselage
Velcro A (1)
Velcro B (1)
Firewall (1)
AS6648 Main Wing
Wing (1)
Aileron (L/1,R/1)
1.5 CFK Rod 230 (2)
1.5 CFK Rod 98 (2)
AS6649 Tail
Horizontal Tail (1)
2 CFK Rod 340 (1)
1.5 CFK Rod 180 (2)
AS6650 Pushrod
No.2354 OBL 29/09-07A
Clevis (4)
Pushrod (4)
Cross Mount (1)
AS6651 Landing Gear
Mount (2)
Landing Gear (2)
Adaptor (1)
Wheel Colar (2)
PARTS DRAWINGS
Fuselage (1)
Tail Gear (1)
2.3x12mm Wood Screw (1)
Glue (1)
Hinge (8)
1.5 CFK Rod 390 (2)
AS6653 11x8 SF Propeller
5 11X8 Propeller (1)
Vertical Fin (1)
AS6652 Control Horn
FRP Control Horn (4)
Reinforced Plate (1)
Hinge (4)
2x5mm Screw (3)
3x6mm Wood Screw (4)
3x6mm Sink Screw (4)
AS6336 Wheel
Prop Nut (1)
Superlite Wheel (2)
Outrunner Brushless Motor 29/27-07A (1)
3
Advertisement
