Color Temperature - Mitsubishi XL1X S L 2 User Manual

Color temperature

1. Select COLOR TEMP in IMAGE menu.
2. Press the $ or % button to select USER
3. Press the ENTER button.
COLOR TEMP.-USER
CONTRAST R
CONTRAST B
BRIGHTNESS R
BRIGHTNESS B
4. Press the { or } button to select the desired item.
5. Press the $ or % button to adjust the item.
6. Repeat steps 4 and 5 for more adjustments.
7. Exit the menu system by pressing the MENU but-
ton several times.
About color temperature
There are different kinds of white color. Color
temperature is a way to show the differences. The
white, which temperature is low, becomes reddish
white. When the color temperature is higher, the
white becomes more bluish. This projector sets
this color temperature by changing the numbers
of contrast blue and red.
To set the color temperature high:
Set the contrast B (Blue) number high, and the
contrast R (Red) number low.
To set the color temperature low:
Set the contrast B (Blue) number low, and the
contrast R (Red) number high.
Adjustment from personal computer
Although this projector sets proper signal systems
automatically for the image signal from personal
computers, it cannot be applied to some of personal
computers. In this case, press the AUTO POSITION
button. If the images are still not projected correctly,
use the MENU display to adjust the projected im-
ages.
opt.
SIGNAL
MEMORY CALL
A
U
HORIZ. POSITION
VERT. POSITION
FINE SYNC.
TRACKING
COMPUTER INPUT
R G B
R G B
HOLD
USER MEMORIZE
Image moved to right or left :
Adjust HORIZ. POSITION in SIGNAL menu. Press
the % button to move the image to left. Press the $
button to move the image to right.
.
0
0
0
0
XGA60
AUTO
0
0
0
0
RGB
AUTO
DELETE DEFAULT
Image moved to up or down :
Adjust VERT. POSITION in SIGNAL menu. Press
the % button to move the image to upward. Press
the $ button to move the image to down.
Image flickers / Image is out of focus :
Adjust FINE SYNC. in SIGNAL menu.
SIGNAL-USER
CLAMP POSITION 0
CLAMP WIDTH 0
HORIZ. PIXELS 0
VERT. LINES 0
VERT. SYNC. AUTO
SHUTTER(U) 0
SHUTTER(L) 0
SHUTTER(LS) 0
SHUTTER(RS) 0
Wide stripes appear :
Adjust CLAMP POSITION or CLAMP WIDTH of
each menu in SIGNAL - USER menu.
Noise appears on right or left side of image :
Adjust SHUTTER (LS), SHUTTER (RS) or HORIZ.
PIXELS of the menu in SIGNAL - USER menu.
Noise appears on top or bottom part of image :
Adjust SHUTTER (U), SHUTTER (L) or VERT.
LINES of the menu in SIGNAL - USER menu.
Top part of image curves :
Change the setting of HOLD in SIGNAL menu.
Select ON , press the ENTER buttun and adjust
BEGIN or END for image which top part is the least
curved.
Image does not move naturally :
Adjust VERT. SYNC. of the menu in SIGNAL -
USER menu. Select AUTO for normal setting.
curved. Select AUTO for normal setting.
• Do not change each menu setting in USER
menu for normal setting.
Simple adjustment method
1. Select HORIZ. POSITION in SIGNAL menu.
2. Press the$ or % button to adjust the horizontal
start position (the left side of image).
3. Select TRACKING in SIGNAL menu.
4. Press the$ or % button to adjust the horizontal
end position (the right side of image).
5. Repeat steps 1 to 4 for fine adjustment.
6. Select VERT. POSITION in SIGNAL menu.
7. Press the$ or % button to adjust the vertical
start position (the top end of image).
EN – 19