Wall Outlet Cable (No Cable Box); Antenna With A Single Lead; Antennas With Separate Uhf And Vhf Leads; Standard Cable Box, Satellite Receiver, Or Other Device With S-Video - Mitsubishi Electric WD-60735 Owner's Manual

20
3. TV Connections

Wall Outlet Cable (no cable box)

It is very important to connect the incoming cable for
your primary viewing source to ANT 1.
1.
Connect the primary incoming coaxial lead cable to
ANT 1 on the TV back panel.
2.
For an optional secondary antenna source, connect
an antenna (or cable) to ANT 2.
3D
GLASSES
EMITTER
ANT 2 / AUX
ANT 1 / MAIN
AVR
AUDIO HDMI
OUTPUT
VIDEO: 480i/480p/720p/1080i/1080p
DVI/PC INPUT R AUDIO L VIDEO AUDIO: PCM STEREO
R AUDIO L
PC: VGA, W-VGA, SVGA, W-SVGA,
L IR- NetCommand R XGA, W-ZGA, SXGA, 720p/ 1080p
Output / External
Controller Input HDMI
ANT 2 / AUX ANT 2 / AUX Pb Pr
ANT 1 / MAIN ANT 1 / MAIN Y
R 1 2
Y/ VIDEO Pb Pr
S-VIDEO
R AUDIO L (480i / 480p / 720p / 1080i)
DIGITAL INPUT 3
AUDIO
OUTPUT
Figure 4. Wall Outlet Cable

Antenna with a Single Lead

A.
For an antenna with flat twin leads
Required: 300-ohm-to-75-ohm transformer.
A1. For an antenna with flat twin leads, connect the
300-ohm twin leads to the 300-ohm-to-75-ohm
transformer.
A2. Push the 75-ohm side of the transformer onto
ANT 1 on the TV back panel.
B.
For cable or antenna with coaxial lead
Connect the coaxial lead directly to ANT 1 on the
TV back panel.
3D
GLASSES
EMITTER
AVR
HDMI
AUDIO
OUTPUT VIDEO: 480i/480p/720p/1080i/1080p
DVI/PC INPUT R AUDIO L VIDEO AUDIO: PCM STEREO
R AUDIO L
PC: VGA, W-VGA, SVGA, W-SVGA,
IR- XGA, W-XGA, SXGA, 720p/ 1080p
L NetCommand R
Output / External
Controller Input HDMI
ANT 2 / AUX
Y Pb Pr
ANT 1 / MAIN ANT 1 / MAIN R 1 2 3
Y/ VIDEO Pb Pr
S-VIDEO
DIGITAL R AUDIO L (480i / 480p / 720p / 1080i) INPUT 3
AUDIO
OUTPUT
ANT 1 / MAIN
Figure 5. Connecting a Single Antenna Lead
Antennas with Separate UHF and
VHF Leads
Required: UHF/VHF combiner
1.
Connect the UHF and VHF antenna leads to the
UHF/VHF combiner.
2.
Push the combiner onto ANT 1 on the TV back
panel.
3
3D
GLASSES
EMITTER
AVR
AUDIO
OUTPUT
DVI/PC INPUT R AUDIO L VIDEO
R AUDIO L
L
ANT 2 / AUX Pr
Y Pb
ANT 1 / MAIN R
Y/ VIDEO Pb Pr
R AUDIO L S-VIDEO
DIGITAL (480i / 480p / 720p / 1080i)
AUDIO
OUTPUT
ANT 1 / MAIN
Figure 6. Connecting separate UHF and VHF Antennas
Mitsubishi strongly recommends you avoid using
antennas with flat twin leads. Flat twin lead
antenna wires are subject to interference which
may adversely affect the performance of the TV.
We recommend using coaxial antenna cable.
Standard Cable Box, Satellite Receiver,
or Other Device with S-Video
Required: S-Video cable and left/right analog stereo
audio cables.
1.
Connect the cable from the outside cable or satel-
lite service to CABLE IN or SATELLITE IN on the
cable box or satellite receiver.
2.
Connect an S-Video cable from
the cable box or satellite receiver back panel to
INPUT 3 S-VIDEO on the TV back panel.
3.
Connect left (white) and right (red) audio cables
from AUDIO OUT on the cable box or satellite
receiver to INPUT 3 AUDIO L and R on the TV back
panel.
Note: Refer to the cable box or satellite receiver
Owner's Guide for cable or dish antenna con-
nections to the receiver.
3D
GLASSES R AUDIO L
EMITTER
HDMI
VIDEO: 480i/480p/720p/1080i/1080p
AUDIO: PCM STEREO
PC: VGA, W-VGA, SVGA, W-SVGA,
IR- NetCommand R XGA, W-XGA, SXGA, 720p/ 1080p
Output / External
Controller Input HDMI
1 2 3
DVI/PC
R
L
AVR
AUDIO
ANT 2 / AUX
OUTPUT
INPUT 3 ANT 1 / MAIN R
R
DIGITAL
AUDIO
OUTPUT
Figure 7. Connecting a device with S-Video
Required: Two-way RF splitter, two coaxial cables, right
and left analog audio cables, either S-video or compos-
ite video cable.
1.
S-VIDEO OUT on 2.
3.
4.
5.
S-VIDEO
INPUT 3
HDMI
VIDEO: 480i/480p/720p/1080i/1080p
INPUT R R AUDIO AUDIO L L VIDEO AUDIO: PCM STEREO
AUDIO L
PC: VGA, W-VGA, SVGA, W-SVGA,
IR- NetCommand R XGA, W-ZGA, SXGA, 720p/ 1080p
Output / External
Controller Input HDMI
Y Pb Pr
1 2 3
Y/ VIDEO Pb Pr
AUDIO L (480i / 480p / 720p / 1080i) S-VIDEO S-VIDEO
INPUT 3 INPUT 3
Figure 8. Connecting a VCR to an Antenna or Wall
Outlet Cable
3. TV Connections
VCR to an Antenna or
Wall Outlet Cable
Connect the incoming cable or antenna to IN on the
RF splitter.
Connect one coaxial cable from OUT on the RF
splitter to ANTENNA IN on the VCR back panel.
OUT on the RF
Connect one coaxial cable from
splitter to ANT 1 on the TV back panel.
Connect either an S-Video or composite video
cable from VIDEO OUT on the VCR back panel to a
VIDEO composite or S-VIDEO jack on the TV back
panel. Connect only one type of video cable;
S-Video is recommended, if available.
To use the TV speakers with the VCR, connect left
(white) and right (red) audio cables from AUDIO OUT
on the VCR to the associated AUDIO L and R jacks
on the TV back panel. If your VCR is mono (non-
stereo), connect only the white (left) cable.
3D
GLASSES
ANT 1 / MAIN
EMITTER
S-VIDEO
INPUT 3
AVR
AUDIO HDMI
OUTPUT DVI/PC INPUT VIDEO: 480i/480p/720p/1080i/1080p
R R AUDIO AUDIO L L VIDEO VIDEO AUDIO: PCM STEREO
R AUDIO L
PC: VGA, W-VGA, SVGA, W-SVGA,
L IR- NetCommand R XGA, W-ZGA, SXGA, 720p/ 1080p
Output / External
Controller Input HDMI
ANT 2 / AUX Pr
Y Pb
ANT 1 / MAIN ANT 1 / MAIN R 1 2 3
Y/ VIDEO Pb Pr
AUDIO L S-VIDEO S-VIDEO
DIGITAL R (480i / 480p / 720p / 1080i) INPUT 3 INPUT 3
AUDIO
OUTPUT
R AUDIO L
VIDEO
21